MOUNT PRO PR1001 Single Monitor Desk Mount Instruction Manual

June 17, 2024
MOUNT PRO

MOUNT PRO PR1001 Single Monitor Desk Mount

MOUNT-PRO-PR1001-Single-Monitor-Desk-Mount-PRODUCT

If you have any questions, please feel free to contact Customer Service via Amazon before returning.

Product Dimensions

MOUNT-PRO-PR1001-Single-Monitor-Desk-Mount-FIG-1

WARNING!

NOTE: Not all hardware included will be used.

BEFORE ASSEMBLY

  • Layout all components and hardware. Check all parts are included and undamaged.
  • Should anybody intends to install or use this mount, please read and understand this manual carefully.
  • If you do not understand these instructions or have any doubt about the safety instructions, assembly or use of this product, please contact our customer service.

WARNING

  • This product contains small items that could be a choking hazard if swallowed.
  • KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
  • Improper installation, such as using the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use

CAUTION AND MAINTENANCE

  • Never allow children to climb, stand, hang, or play on any part of monitor or stand.
  • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
  • Check that the bracket is secure and safe to use at regular intervals (at least every three months).

PACKAGE CONTENTS

MOUNT-PRO-PR1001-Single-Monitor-Desk-Mount-FIG-2

ASSEMBLY STEPS

STEP 1: Pads Installation

  • Apply pads (E) to the base bottom to avoid desk scratches.MOUNT-PRO-PR1001-Single-Monitor-Desk-Mount-FIG-3

STEP 2: Base Installation

OPTION A: Clamp Installation
Remove the plastic sleeve (C1) and plastic cover (C2) from Base (C3). Mount Clamp (D) to the bottom of Base (C3) by tightening bolts (K) with 5mm Allen Key (I).MOUNT-PRO-PR1001-Single-Monitor-Desk-Mount-
FIG-4

  • Adjust the Clamp thickness clearance to fit your desk.
  • Secure the stand to the desktop by tightening the clamp (D). Fix the plastic sleeve (C1) and plastic cover (C2) to Base (C3).

MOUNT-PRO-PR1001-Single-Monitor-Desk-Mount-FIG-5

STEP 2: (Continued)

OPTION B: Grommet Base Installation
If existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount. Firstly detach Bracket (D1) from Clamp (D).MOUNT-PRO-PR1001-Single-Monitor-Desk-Mount-
FIG-6

  • Then remove the plastic sleeve (C1) and plastic cover (C2) from Base (C3). Run Carriage Bolt(G) through Base (C).MOUNT-PRO-PR1001-Single-Monitor-Desk-Mount-FIG-7
  • By tightening Wingnut (F) after making Bracket (D1) through Carriage Bolt (G) and stacking above Wingnut (F), Base (C3) would be fixed to your desk securely. Install the plastic sleeve (C1) and plastic cover (C2) to Base (C3) finally.MOUNT-PRO-PR1001-Single-Monitor-Desk-Mount-FIG-5

Arm Installation

Install the lower arm (B) to the base (C). Attach the upper arm (A) with a plastic sleeve (L) to the lower arm. Secure the arm by tightening the inside screw using 3mm Allen key (H).MOUNT-PRO-PR1001-Single-Monitor-Desk-Mount-
FIG-9

Monitor Installation

If provided M-A/M-B screws do not fit your monitor, please contact us to get suitable screws.

MOUNT-PRO-PR1001-Single-Monitor-Desk-Mount-FIG-10 MOUNT-PRO-PR1001-Single-Monitor-Desk-Mount-FIG-11

Tilt Adjustment

Problem: Monitor tilts down.MOUNT-PRO-PR1001-Single-Monitor-Desk-Mount-
FIG-12

Solution

  1. Loosen the tilting bolt.
  2. Hold the bottom of the monitor with one hand and adjust to determine your desired tilt angle.
  3. Retighten the tilting bolt to fix the intended angle.MOUNT-PRO-PR1001-Single-Monitor-Desk-Mount-FIG-12

Tension Adjustment

The gas spring is pre-set for a load-bearing range of 8.8 lbs -13.2 lbs. For the intended functioning of the mount, you will need to adjust the tension of the Upper Arm (A) by your monitor weight by 6mm Allen Key (J).MOUNT-PRO-
PR1001-Single-Monitor-Desk-Mount-FIG-13

Note: Be sure to keep the arm in a horizontal position during adjustment. Or else it would be difficult to adjust the mount or damage the mount.MOUNT-
PRO-PR1001-Single-Monitor-Desk-Mount-FIG-16

Situation 1: Arm falls down
The Upper Arm with the monitor falls and fails to stay where intended.

Solution
Turn the inside screw counterclockwise (“+” direction) to increase gas spring tension until the arm can stay as intended.

Situation 2: Arm rises up or can’t press down Upper Arm with monitor rises up and fails to stay where intended.

Solution
Turn the inside screw clockwise (“-” direction) to decrease gas spring tension until the arm can stay as intended.

Cable Management

MOUNT-PRO-PR1001-Single-Monitor-Desk-Mount-FIG-17

Adjust as Desired

  • Adjust monitor position and rotation. MOUNT-PRO-PR1001-Single-Monitor-Desk-Mount-FIG-18

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals