MOUNT PRO ZDT10 Single Screen Vertical Single Monitor Stand Instruction Manual

MOUNT PRO ZDT10 Single Screen Vertical Single Monitor Stand

Product Information

Specifications

• Weight Capacity: 33 lbs (15 kg)
• VESA Mounting Patterns: 75x75mm, 100x100mm
• Rotation: 360 degrees
• Tilt: 35mm/1.38 inches
• Swivel: 360mm/14.17 inches
• Maximum Height: 641mm/25.24 inches
• Minimum Height: 361mm/14.21 inches

Product Usage Instructions

Step 1: Before Assembly

Before assembling or using this product, please contact our customer service if you have any questions.

Step 2: Supplied Parts and Hardware

The following parts and hardware are included:

• Support Pillar (Upper)
• Base Plate Component
• Support Pillar (Lower)
• Connecting Plate
• Hardware (Product)
• Bolt M6 x 30mm
• Washer
• Handle Bolt Plastic Cover
• Wire Clip
• Foot Pad
• Allen Key
• Bolt 4mm / 5mm M6 x 10mm

Step 3: Support Pillar Installation

1. Connect two Support Pillars (23 & 34) using the Connecting Plate 5 and Bolts (H).
2. Tighten the bolts using the 4mm Allen Key (H).

Step 4: Apply Foot Pads to the Base

1. Hold the Support Pillar 4 with one hand and remove the plastic film from the Foot Pads (F).
2. Attach the Foot Pads (F) near the four corners of the Base 1 bottom.

Step 5: Attaching the Base and Support Pillar

1. Place the Base 1 on the table.
2. Place Washers (B) and Bolts (A) on the base, ensuring that the clip holes of Support Pillar 4 are facing toward the backside of the base.
3. Put the Plastic Cover (D) and Support Pillar 4 under the base.
4. Tighten the bolts (A) using the 4mm Allen Key (G).

Step 6: Attaching the Plate Component to the Monitor

Select the appropriate screw length for your monitor.

1. Thread screws by hand into the threaded holes on the back of your monitor.
2. Select which screw diameter fits your monitor.

For Flat Back Monitor:

• Use shorter screws MA, MC, and ME. If the MA screw is too long, use a H5mm spacer to fix it.

For Recessed/Curved Back Monitor:

• Use longer screws MB, MD, MF.

Step 7: Attaching the Monitor to the Support Pillar

1. Choose the appropriate position for your monitors and hang them onto the Support Pillar.
2. Make sure the ARROW mark on the plate component is pointing upwards.
3. When attaching the plate to the flat screen, be careful not to over-tighten screws and ensure that screws do not bottom out in the mounting holes.

Step 8: Cable Management

Attach Wire Clips (E) into the holes of the Support Pillar to manage cables.

FAQ

Q: What is the weight capacity of this product?

• A : The weight capacity is 33 lbs (15 kg).

Q: What are the compatible VESA mounting patterns?

• A : The compatible VESA mounting patterns are 75x75mm and 100x100mm.

Q: How much rotation does this product allow?

• A : This product allows 360 degrees of rotation.

Q: How much tilt does this product allow?

• A : This product allows a tilt of 35mm/1.38 inches.

Q: Can I use this product with a curved back monitor?

• A : Yes, you can use this product with a curved back monitor. Use the longer screws provided.

Q: How do I manage cables with this product?

• A : Attach the Wire Clips (E) into the holes of the Support Pillar to manage cables.
• If you have any questions, please feel free to contact Customer Service via Amazon before returning.

Safety Caution

BEFORE ASSEMBLY

• Layout all components and hardware. Check all parts are included and undamaged.
• Should anybody intend to install or use this monitor stand, please read and understand this manual carefully.
• If you do not understand these instructions or have any doubt about the safety instructions, assembly, or use of this product, please contact our customer service.

WARNING

• This product contains small items that could be a choking hazard if swallowed.
• KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
• Improper installation, such as using the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury.
• We would not be liable for any damage or injury caused by improper mounting or inappropriate use.

CAUTION AND MAINTENANCE

• Never allow children to climb, stand, hang, or play on any part of the monitor or stand.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).

Installation Tools (Not Included)

Supplied Parts and Hardware

NOTE: Not all hardware included will be used.

Product Dimensions

STEP 2: Support Pillar Installation

• Connect two Support Pillars ( & ) by using the Connecting Plate and Bolts (H).
• Use the 4mm Allen key (H) to tighten the bolts.
• Put Base on the table; put Washers (B) and Bolts (A) on the base; keep clip holes of 4Support Pillar toward backside then put Plastic Cover (D) and Support Pillar under the base. Then tighten the bolts (A) with the 4mm allen key (G).

STEP 3: Apply Foot Pads to the Base

• Hold the Support Pillar with one hand and tear off a plastic film of the Foot Pads (F), then attach Foot Pads (F) near the four corners of the Base bottom.

STEP 3: Attach the Plate Component to Monitor

Select Monitor Screw Length

• Thread screws by hand into the threaded holes on the back of your monitor and then select which screw diameter fits your monitor.
• When attaching a plate to the flat screen, be careful not to over-tighten screws and be sure that screws do not bottom out in the mounting holes.

Attach the Plate Component

• (a) For Flat Back Monitor
• (b) For Recessed / Curved Back Monitor

STEP 4: Attach Monitor with Plate Component to Pillar

1. Choose the appropriate position for your monitors, and hang the monitors onto the Support Pillar.

STEP 5: Cable Management

• Attach Wire Clips (E) into the holes of the Support Pillar. Manage cables with the Wire Clips (E).

STEP 6: Adjustments (If necessary)

Tilt Adjustment

1. Slightly loosen the tilting bolt with the Allen Key(G).
2. Hold the monitor with both hands and adjust the monitor to your desired tilt angle.
3. Retighten the tilting bolt to secure the monitor in place.

Note: When tilted, if the monitor sags or does not stay, and if the above method is useless, please feel free to contact our customer service.

STEP 6: Adjustments (If necessary)

Leveling Adjustment

Swivel Adjustment

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>