MOUNT PRO SG06-21 Premium Single Monitor Stand Instruction Manual
- June 17, 2024
- MOUNT PRO
Table of Contents
MOUNT PRO SG06-21 Premium Single Monitor Stand
Premium Single Monitor Stand Instruction
MOUNT-PRO-SG06-21-Premium-Single-Monitor-Stand-product
SAFETY INSTRUCTIONS
BEFORE ASSEMBLY
- Layout all components and hardware. Check all parts are included and undamaged.
- Should anybody intends to install or use this monitor arm, please read and understand this manual carefully.
WARNING
- This product contains small items that could be a choking hazard if swallowed.
- KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
- Improper installation, such as using the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
- If you do not understand these instructions or have any doubt about the safety instructions, assembly or use of this product, please contact our customer service.
Part List
VESA SCREWS
ASSEMBLY STEPS
STEP 1: Mounting the Base
- OPTION A: Clamp Installation
- Secure the stand to the desktop by tightening the Clamp with the Allen key (6).
- OPTION B: Grommet Installation
- Insert the long bolt (5) through the plate (4) and the hole on the tabletop, and then use the Allen key (6) to tighten.
STEP 2: Arm Installation
- Turn the head to the straight by hand before assembling the arm.
- Insert the arm into the base and adjust the screw with the Allen key (7) to fix the lower arm.
STEP 3 : Attach Monitor
-
OPTION A: Flat Back Monitor
Attach the VESA plate (3) to the back of the monitor and secure it by using a 5mm Allen Key (6) to tighten screws along with washers.
Warning Do not tighten the screws excessively or your monitor might be damaged. -
OPTION B: Curved / Recessed Back Monitor
Attach the VESA plate (3) to the back of the monitor and secure it by using a 5mm Allen Key (6) to tighten screws along with washers and spacers.
WARNING Do not tighten the screws excessively or your monitor might be damaged.
STEP 4: Hang Monitor and Adjust Monitor Tilting Angle
-
Slide the monitors onto the head of the arm.
Important Notice:
The pressure of the gas spring is initially set to an intermediate value. So when the monitor hangs, make sure to hold it with both hands and don’t let it drop suddenly. -
If the tilt adjustment mechanism is too tight or too loose, please adjust the screw as shown below.
-
STEP 5: Adjust Gas Spring Tension
For proper functioning of this mount, depending on the different weights of the monitor you might need to adjust the tension in the upper arm (1).-
Situation 1: Arm falls down
Upper Arm with monitor falls and fails to stay where intended. -
Situation 2: Arm rises up / can’t be pressed down
The Upper Arm with the monitor rises up automatically or can’t be pressed down and fails to stay where intended.
-
STEP 6: Cable Management
-
Remove Cable Cover
Remove two keys first, then remove the cover. -
Attach Cable Cover
Insert the cover first, then install the two keys.
Adjust as Desired
Adjust monitor position and rotation
Note : To ensure stability, the tightness of the rotating axis has been
presented, so it would be kind of difficult to rotate the VESA plate.
Suggestion : Please attach the monitor first, then hold the two sides of
it with both hands and rotate vigorously. If that doesn’t work out, please do
not hesitate to ask for our help.
WARNING:
For your safety, do not move the standoff your desk!
Product Dimensions
CAUTION AND MAINTENANCE
- Never allow children to climb, stand, hang, or play on any part of the monitor or stand.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>