MOUNT PRO B0B7W2VJY5 Single Monitor Wall Mount Arm Instruction Manual
- June 15, 2024
- MOUNT PRO
Table of Contents
MOUNT PRO B0B7W2VJY5 Single Monitor Wall Mount Arm
Product Information
Specifications:
- Product Model: CX02-01-C_US1.0
- Product Dimensions:
- Width: 0.79″ / 20mm
- Height: 0.39″ / 10mm
- Wall Plate: 4.8″ / 122mm
- Adjustable Arm Length: 7.6″ to 11″ / 192mm to 280mm
- Monitor Plate Width: 2.1″ / 53mm
- Monitor Plate Height: 2.95″ / 75mm
- Monitor Plate Depth: 3.94″ / 100mm
- Maximum Extension: 4.4″ / 112mm
- Minimum Distance to Wall: 1.2″ / 31mm
- Total Height: 7.3″ / 185mm
- Total Width: 12.2″ / 310mm
- Load Capacity: 4.4 lbs to 19.8 lbs (2 kg to 9 kg)
Product Usage Instructions
Installation:
- Please read the installation instructions carefully before proceeding.
- Ensure that you have the necessary tools and equipment for installation.
- This product is designed for use in wood stud or solid concrete walls only. DO NOT install into drywall alone.
- Before starting the installation, verify that your wall is capable of supporting five times the weight of the monitor and mount combined.
- Incorrect installation may result in product damage, property damage, or personal injury. We shall bear no responsibility for any such damage or injury resulting from incorrect installation, assembly, or misuse.
Safety Caution:
- Read the safety instructions carefully before installation.
- If you do not understand the instructions or have doubts about the safety of the installation, assembly, or use of this product, please contact us.
- This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; please contact our customer service team. Never use damaged parts!
Must Check Before Getting Started:
- Verify your monitor specifications:
- Width (W)
- Height (H)
- Load Capacity: 4.4 lbs to 19.8 lbs (2 kg to 9 kg)
- WARNING: DO NOT exceed the maximum weight indicated.
- Verify your wall construction:
- This product is suitable for use in wood stud or solid concrete walls.
- Ensure that your wall is capable of supporting five times the weight of the monitor and mount combined.
Frequently Asked Questions (FAQ)
Can I install this product on a drywall?
No, this product is designed for use in wood stud or solid concrete walls
only. DO NOT install into drywall alone.
What happens if I exceed the maximum weight capacity?
Exceeding the maximum weight capacity can result in product damage,
property damage, or personal injury. It is important to always adhere to the
specified weight limits.
Can I use damaged parts during assembly?
No, never use damaged parts during assembly. This product contains small
items that could be a choking hazard if swallowed. If any parts are missing or
damaged, please contact our customer service team for assistance.
If you have any questions, please feel free to contact Customer Service via Amazon before returning.
Safety Caution
Please read this instruction carefully before installation. If you do not
understand these instructions or have doubts about the safety of the
installation, assembly or use of this product, please contact us.
- This product is designed for use in wood stud or solid concrete wall.
- DO NOT install into drywall alone.
- The wall must be capable of supporting five times the weight of the monitor and mount combined.
- Incorrect installation may result in product damage/property damage or body injury.
We shall bear no responsibility for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.
WARNING : This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; please contact our customer service team. Never use damaged parts!
Must Check Before Getting Started
Verify Your Wall Construction:
CAUTION:
Avoid potential personal injuries and property damage! Drywall covering the
wall must not exceed 5/8 in (16 mm).
Minimum wood stud size:
- nominal 2 x 4 in (51 x 102 mm)
- actual 1 ½ x 3 ½ in. (38 x 89 mm).
CAUTION:
Avoid potential personal injuries and property damage!Mount the wall plate
assembly directly onto the concrete surface (no surface covering).
CAUTION : DO NOT install into drywall alone.
ATTENTION : Tension adjustment should be done only after monitor installation
WARNING :
Gas Spring Arm is under pressure and should be handled with care. Failure to
follow the instructions may result in damage to the mount and/or personal
injury.
Product Dimensions
Supplied Parts and Hardware
NOTE : Not all parts and hardware included will be used.
Extra Tools You Need (Not Supplied)
INSTALLATION INSTRUCTIONS
Attach a VESA Plate to Monitor
-
Select Correct Monitor Screw Length
Which Situation Needs Spacers?
If the screw is too long or the surface is uneven, please choose the appropriate screws and spacers for your monitor.
-
Do not tighten the screws excessively or tighten them by using the Electrodrill, or your monitor might be damaged.
2-A Attach Arm to Wall
OPTION A:
Wood Stud Installation
-
Locate your studs. Verify and mark the center of the stud by finding the stud edges using awl and stud finder.
-
Position the mounting template at your desired height and line up the holes with your stud center line. Level the mounting template and mark the pilot hole location
-
Drill pilot holes using a Ф3/16 in (Ф4.5mm) diameter drill bit.
IMPORTANT:
Do not drill holes into where water pipes or electrical wires are located. Be sure to drill into the center of the stud.
-
Install wall plate using lag bolts with Socket Wrench, NO Electrodrill. No anchors when installed onto the wood studs.
CAUTION: To avoid potential personal injury or property damage:
All 3 lag bolts MUST BE firmly tightened to prevent unwanted movement of the
wall plate assembly. Ensure the wall plate assembly is securely fastened to
the wall before continuing on to the next step.
2-B Attach Arm to Wall
OPTION B:
Solid Concrete Wall Installation
-
Level the mounting template and mark the pilot hole locations.
-
Drill pilot holes using a Ф3/8 in (Ф10mm) diameter drill bit.
IMPORTANT: Do not drill holes into where water pipes or electrical wires are located, or mortar between blocks. -
Use the hammer to knock anchors into the concrete wall. Be sure the anchors are seated flush with the concrete surface. Install wall plate using lag bolts and anchors with Socket Wrench, NO Electrodrill
Hang Monitor
- Remove the pre-assembled security bolt (A0) from the arm (A).
- Slide the monitor onto the head of arm (A), then install the security bolt (A0).
- Make sure the security bolt (A0) is installed before you rotate the monitor.
Adjustments (If necessary)
Tilt Adjustment
- Loosen the tilting bolt.
- Adjust monitor to your desired tilt angle.
- Retighten the tilting bolt to fix the intended angle.
Tension Adjustment
The gas spring is pre-set to minimum tension (4.4 lbs). For intended functioning of the mount, you may need to adjust the tension of Arm in accordance with your monitor weight by 6mm Allen key (W-B).
Note:
Be sure to keep the arm in a horizontal position during adjustment. Or else it
would be difficult to adjust the mount or damage the mount
-
Situation 1: Arm falls down
Upper Arm with monitor falls down and fails to stay where intended.
Solution:
Turn the inside screw counterclockwise (“+”direction) to increase gas spring tension until the arm can stay as intended. -
Situation 2: Arm rises up or can’t press down
Upper Arm with monitor rises up and fails to stay where intended.
Solution:
Turn the inside screw clockwise (“-”direction) to decrease gas spring tension until the arm can stay as intended
**Cable Management
**
-
Upper Arm
Remove the cable cover from upper arm.
Run cables through the cable cover, then insert the cable cover to upper arm. -
Lower Arm
Remove the bottom plastic cover from lower arm as shown in the diagram.
Run cables through the cable cover, then insert and slide the cover down for reattachment -
Adjust monitor position and rotation
Note : To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate.
Suggestion : Please attach the monitor first, then hold the sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>