MOUNT PRO PR6005D-MA01N-12-US1.0 Premium Single Monitor Stand Instruction Manual

: June 15, 2024
: MOUNT PRO

MOUNT PRO PR6005D-MA01N-12-US1.0 Premium Single Monitor Stand Instruction

Manual

WARNING!

If you have any confusion or are not quite sure about the installation, please do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are included and undamaged. Imprope installation, such as using the product for monitors over its load capacity or for any purpose not explicitly specied, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF
CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

ASSEMBLY STEPS

STEP 1: Clamp Installation OR Grommet Base Installation

OPTION A: Clamp Installation

Mount Bracket (D) to Base (C) with Bolts (L). Bolts could be tightened by the 4mm Allen Key (P).
Apply pads (M) to the Bolts (L) to avoid desk scratches.

Similarly, attach Clamp (G) to Bracket (D) with Bolts (L) and 4mm Allen Key (P)

Adjust the Clamp width to t with desk. Secure stand to desktop by tightening Clamp (G) or by Allen key (Q).
Attach Base Support Cover (E) to Bracket (D).

STEP 1: (Continued)

OPTION B: Grommet Base Installation
Place Carriage Bolt (H) through the center of Grommet Base (I).
Mount Grommet Base to Base (C) bottom with Bolts (L) and tighten by 4mm Allen Key (P).
Apply pads (M) to the Bolts (L) to avoid desk scratches.

Run Carriage Bolt (H) through Grommet Hole on desktop. Attach Support Plate (J) and Wingnut (K).
At last, tighten Wingnut (K).

STEP 2: Arm Installation

Install the lower arm (B) and the upper arm (A) to the base (C). Secure the arm by tightening the inside screw using a 3mm Allen Key (O).

STEP 3 : Attach Monitor

OPTION A: Flat Back Monito 05 Monitor
MonitorMonitor MonitorNo No!
Attach the VESA plate (F) to the back of monitor and secure it by using a 6 mm Allen Key (Q) to tighten screws (M-A ) .
Do not tighten the screws excessively or your monitor might be damaged

OPTION B: Curved Back Monitor

OPTION A: Flat Back Monitor

Attach the VESA plate (F) to the back of monitor andsecure it by using a 6 mm Allen Key (Q) to tightenscrews (M-A ) .
Do not tighten the screws excessively or your monitor might be damaged.
Attach the VESA plate (F) to the back of monitor and secure it by using a 6 mm Allen Key (Q) to tighten screws (M-B) along with spacers (M-C).
Do not tighten the screws excessively or your monitor might be damaged.

STEP 4: Hang Monitor

Slide the monitor onto the head of swivel arm, install the security bolt (N). Make sure the security bolt is installed before you rotate the monitor.

Important Notice:

The pressure of the gas spring is initially set at the lowest value. So whennthe monitor is hung on, make sure you hold it with both hands and DO NOT let it go down suddenly.

Guideline to adjust monitor tilting angle

Problem:

If monitor faces downSolution:

Loosen the tilting bolt.
Hold the bottom of monitor with one hand and adjust to determine your desired tilt angle.
Retighten the tilting bol towards “＋” to x the angle

STEP 5: Adjust Tension

For proper functioning of this mount, depending on dierent weight of monitor you might need to adjust tension in upper arm (A) using 6 mm Allen Key (Q).

Note2:

As for how many circles the screw should be turned, the table below is for reference.

STEP 6: Cable Management

Remove Cable Cover

Remove bottom plastic covers from arm as shown in diagram. Do not need to take much eort to pull the ends of the cable cover away from the arm

Attach Cable Cover

Run cables from monitor through bottom of arm. Reattach plastic covers as shown in diagram

Adjust as Desired 09

Allen key(Q,O) can be stored in Base Support Cover(E) for next time using

Note:

When tilted, if the monitor sags or does not stay, please fasten the tilting bolt on the mount until the monitor can be held at any angle as needed.

Tilt
Swivel
Rotation
Height

Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of dicult to rotate the VESA plate.
Suggestion: Please attach the monitor rst, then hold the two sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.

Product Dimensions

CAUTION AND MAINTENANCE:

Never allow children to climb, stand, hang, or play on any part of monitor or stand.
This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
Check that the bracket is secure and safe to use at regular intervals (at least every three months).