MOUNT PRO APH-53-6-13 Dual Monitor and Laptop Mount Instruction Manual
- June 15, 2024
- MOUNT PRO
Table of Contents
Dual Monitor and Laptop Mount
Instruction Manual
APH-53-6-13 Dual Monitor and Laptop Mount
**|
---|---
75x75mm
100x100mm**| (2~9kg)x3
(4.4~19.8lbs)x3
If you have any questions, please feel free to contact our customer service via Amazon.
WARNING!
If you have any confusions or are not quite sure about the installation,
please do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are
included and undamaged. Improper installation, such as use the product for
monitors over its load capacity or for any purpose not explicitly specified,
may cause damage or serious injury. We would not be liable for any damage or
injury caused by improper mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed.
Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION
IS REQUIRED.
PACKAGE CONTENTS
DO NOT EXCEED WEIGHT CAPACITY.
(2~9kg)x3
(4.4~19.8lbs)x3
NOTE : Not all hardware included will be used.
ASSEMBLY STEPS
STEP 1: Apply Pads To The Base Bottom
Paste the Pad (F1) onto the Base (F)
STEP 2: Clamp Installation Or Grommet Base Installation
OPTION A: Clamp Installation
Align the screw hole on the Base (F), then lock the Screw (B3) with a 5mm
Allen Key (K).
Put the Clip Plate (B-1) on the Bolt Y (B2)
Fix the bracket on the table by tightening the Clamp (B), then fix the Decorative Cover (C) to the Base (F).
OPTION B: Grommet Base Installation
Ensure the desktop has a hole between 0.39”~2.36” (10mm~60mm) in diameter to
use this option.
Use 5mm Allen Key(K) to detach Bolts(B3)and Bolt Y(B2) from Clamp(B).
Use Bolt Y (B2) through the screw hole on Bracket (B1) to fix the base (F) and the table board together. Then fix the Decorative Cover (C) to the Base (F).
STEP 3 : Arm Installation
1: Install Wire Clip (F2) and Swivel Arm (A) to the pole. Lock the bolt on
Swivel Arm (A) with supplied 6mm Allen key (L).
2-1: Install Wire Clip (G1) to Middle Arm (G).
2-2: Install Plastic Parts (I) to Middle Arm (G).
2-3: Install Middle Arm (G) to the pole, then Lock the bolt on Middle Arm (G)
with supplied 6mm Allen key (L). STEP 4 : Front-panel Installation
Install Laptop Tray (E) to the Middle Arm (G), Apply pads (E1) to the Laptop
Tray (E) to avoid laptop scratches.
- Install the top two screws first
- And then you attach the Laptop Tray (E) to the Middle Arm (G)
- Finally install the next two screws and tighten all screws
STEP 5 : Attach Monitor
OPTION A: Flat Back Monitor
Attach the VESA plate (D) to the back of monitor and secure it by using a 5mm
Allen Key (K) to tighten screws (M-A) along with washers (M-C).
Do not tighten the screws excessively or your monitor might be damaged.
OPTION B: Curved Back Monitor
Attach the VESA plate (D) to the back of monitor and secure it by using a 5mm
Allen Key (K) to tighten screws (M-A) along with washers (M-C) and Spacer
(M-D).
Do not tighten the screws excessively or your monitor might be damaged.
NOTE : Hand tighten screws to avoid over tightening.
STEP 6 : Hang Monitor
Slide the monitor onto the head of Swivel Arm (A). Install the Security Bolt
(H).
Make sure the security bolt is tightened before you rotate the monitor.
Important Notice:
The pressure of the gas spring is initially set at the lowest value.
So when the monitor is hung on, make sure you hold it with both hands and DO
NOT let it go down suddenly.
STEP 7 : Tilt Adjustment
- Slightly loosen the tilting bolt.
- Adjust monitor and laptop tray to your desired tilt angle.
- Retighten tilting bolt to secure the monitor and front-panel in place.
STEP 8 : Gap Spring Tension Adjustment
For intended functioning of the mount, you may need to adjust the tension of Arm (A) in accordance with your monitor weight by 6 mm Allen Key (L).
Note1:
Be sure to keep the arm in horizontal position during adjustment.
Or else it would be difficult to adjust the mount ordamage the mount.
Situation 1: Arm falls down
Upper Arm with monitor falls down and fails to stay where intended.
Solution:
Turn the inside screw counterclockwise(“+”direction) to increase gas spring
tension until the arm can stay as intended.
Situation 2: Arm rises up
Upper Arm with monitor rises up and fails to stay where intended.
Solution:
Turn the inside screw clockwise(“-”direction) to decrease gas spring tension
until the arm can stay as intended.
Note2: For how many circles the screw should be turned, please refer to the table below.
| Monitor Weight | 2kg | 3kg | 4kg | 5kg | 6kg | 7kg | 8kg | 9kg |
|---|---|---|---|---|---|---|---|---|
| Circles(AT LEAST) | min | 2 | 4 | 6 | 8 | 10 | 12 | 15 |
STEP 9 : Cable Management
Run cables through the cable cover as shown in diagram.
Adjust as Desired
Adjust monitor position and rotation.
Note : To ensure stability, the tightness of the rotating axis has been
preset, so it would be kind of difficult to rotate the VESA plate.
Suggestion : Please attach the monitor first, then hold the two sides of
it with both hands, and rotate vigorously. If that doesn’t work out, please do
not hesitate to ask for our help.
Product Dimensions
Unit Conversion
1 CM≈0.39 inch
CAUTION AND MAINTENANCE:
- Don’t allow children to climb, stand, hang, or play on any part of monitor or stand.
- This product is intended for indoor use only. Using this product outdoors may lead to product damage or personal injury.
- Check if that the bracket is secure and safe to use at regular intervals (at least every three months).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>