MOUNT PRO H22002 Single Monitor Arm Instruction Manual
- June 16, 2024
- MOUNT PRO
Table of Contents
MOUNT PRO H22002 Single Monitor Arm
WARNING!
- If you have any confusion or are not quite sure about the installation, please do not hesitate to ask for our help via Amazon.
- Before assembly, please check and make sure all necessary accessories are included and undamaged.
- Improper installation, such as use of the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
- The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF THE REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
INFORMATION
PACKAGE CONTENTS
Install the Base
OPTION A: For Clamp Mounting
- Firstly detach Brace (E1) from C-Clamp (E) with 4mm Allen Key (L).
- Mount Brace (E1) to the bottom of Base (A) by tightening Bolts (J) with 4mm Allen Key (L).
- Apply Pads (1) to the base bottom to avoid desk scratches.
- Attach the C-Clamp (E) to the Brace (E1).
- Then tighten the Bolts (E4) with 4mm Allen Key (L).
- Attach the Support Plate (F) to the bolts of C-Clamp (E).
- Secure the stand to the desktop by tightening Bolts (E3).
- Finally, attach the Decorative Cover (H) to the base.
OPTION B: For Grommet Mounting
- Mount Grommet Plate (G) to Base (A) bottom with Bolts (J) and tighten by 4mm Allen Key (M).
- Apply Pad (1) to the base bottom to avoid desk scratches.
- Detach two Bolts (E3) from C-Clamp (E) by using 4mm Allen Key (M).
- Run two Bolts (E3) through the Support Plate (F) and Grommet Hole on the desktop, then tighten the Bolts (E3) with 6mm Allen Key (M).
Install the Arms
Install the Lower Arm (B) and the Upper Arm (C) to the Base (A). Secure the arm by tightening the set screws using 3mm Allen Key (K).
If Necessary
If the metal sheets on the plastic sleeve are losing, you can use a spare
metal sheet (N) for Installation as shown in the diagram.
Attach Monitor
OPTION A: Flat Back Monitor
Attach the VESA Plate (D) to the back of the monitor and secure it with Screws
(M-A or M-B or M-C) and Washers (M-D) using 4mm Allen Key (L).
- Please make sure you don’t tighten the screws excessively or it may cause your monitor damage.
OPTION B: For Recessed / Curved Back Monitor
- Attach the VESA Plate (D) to the back of the monitor and secure it with Screws (M-A or M-B or M-C), Washers (M-D) and Spacers (M-E) using 4mm Allen Key (L).
- Put 4 spacers between the VESA plate and the monitor.
- Install 4 long screws through the VESA plate, and spacers to monitor via mounting holes.
- Please make sure you don’t tighten the screws excessively or it may cause your monitor damage.
Hang Monitor
Note: If you want to remove the monitor, pull the lock plate back and lift the monitor to separate the monitor from the arm.
Tilt Adjustment
Problem
If the monitor faces down.
Solution
- Slightly loosen two preassembled bolts.
- Adjust monitor to your desired tilt angle.
- Retighten both bolts to secure the monitor in place.
Adjust Gas Spring Tension
- For the intended functioning of the mount, you may need to adjust the tension of Arm (C) under your monitor weight by 6mm Allen Key (M).
Note 1:
Be sure to keep the arm in a horizontal position during adjustment.
Or else it would be difficult to adjust the mount or damage the mount.
CAUTION
Situation 1: Arm falls down
The Upper Arm with the monitor falls and fails to stay where intended.
Solution
Turn the inside screw counterclockwise(“+” direction) to increase gas spring
tension until the arm can stay as intended.
Situation 2: Arm rises up
The Upper Arm with the monitor rises and fails to stay where intended.
Solution
Turn the inside screw clockwise(*-“direction) to decrease gas spring tension
until the arm can stay as intended.
Note 2: For how many circles the screw should be turned, please refer to the table below.
Route Cables along the Arm
- Remove the cable cover from the lower arm as shown in the diagram.
- Run cables through the cable cover, then insert and slide the cover down for reattachment.
Adjust as Desired
90° Rotation
This function works better for monitors with the centre of gravity.
Note: To ensure stability, the tightness of the rotating axis has been
preset, so it would be kind of difficult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the two sides of
it with both hands and rotate vigorously. If that doesn’t work out, please do
not hesitate to ask for our help via Amazon.
Product Dimensions
CAUTION AND MAINTENANCE
- Don’t allow children to climb, stand, hang, or play on any part of the monitor or stand.
- This product is intended for indoor use only. Using this product outdoors may lead to product damage or personal injury.
- Check if the bracket is secure and safe to use at regular intervals (at least every three months).
If you have any questions, please feel free to contact our customer service via Amazon.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>