DYNOJET PC6-20062 Power Commander 6 Installation Guide
- June 4, 2024
- Dynojet
Table of Contents
POWER COMMANDER 6
Install guide for PC6-20062
Model coverage: 2020 Suzuki Katana
PARTS LIST
1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS
2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION.
THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map| (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You
can switch on the fl y between these two
base maps when you hook up a switch to the MAP inputs. You can use any
open/close type switch. The polarity of
the wires is not important.
---|---
Shifter| (Input 1 or 2) Used for clutch-less full-throttle upshifts. Insert
the wires from the Dynojet quick shifter into either
Input 1 or Input 2. The polarity of the wires is not important. Set to Input 2
by default.
Speed| If your application has a speed sensor then you can tap into the signal
side of the sensor and run a wire into this
input. This will allow you to calculate gear position in the Control Center
Software. Once gear position is setup
you can alter your map based on gear position and setup gear-dependent kill
times when using a quick-shifter.
Analog| This input is for a 0-5v signal such as engine temp, boost, etc. Once
this input is established you can alter your
fuel curve based on this input in the Power Core software.
Launch| You can connect a wire to either Input 1 or Input 2 and then the other
end to a switch. This switch when engaged
(continuity) will only allow the RPM to be raised to a certain limit (set in
the software). When released, you will
have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 first remove the rubber plug on the backside of the
unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tightens the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
INSTALLING THE POWER COMMANDER 6
-
Remove the seats. Remove the panels around the fuel tank and remove the fuel tank.
-
Lay the PC6 in the tail section on the right-hand side of the battery.
-
Route the PC6 harness around the battery and down the left side of the motorcycle towards the engine.
-
Attach the ground wire of the PC6 to the negative side of the battery.
-
Unplug the stock wiring harness from each injector.
-
Plug the PC6 in line with the stock injectors and wiring harness.
ORANGE wires go to cylinder #1 (LEFT)
YELLOW wires go to cylinder #2
GREEN wires go to cylinder #3
BLUE wires go to cylinder #4
-
Locate the Throttle Position Sensor on the right-hand side of the throttle bodies. Unplug the lower of the 2 connectors.
-
Connect the PC6 in line with the stock TPS and wiring harness.
There are 2 sensors in this location, make sure you are on the lower of the 2. -
Reinstall the fuel tank and bodywork.
Download the latest map files from our website at dynojet.com/tunes.
PUSH THE LIMIT
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081
800-992-4993
DYNOJET.COM
© 2020-2022 DYNOJET RESEARCH
ALL RIGHTS RESERVED
2020-2021 SUZUKI KATANA
PC6-20062
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>