DYNOJET PC6-14044 Power Commander 6 Installation Guide
- October 27, 2023
- Dynojet
Table of Contents
PC6-14044 Power Commander 6
Installation Guide
PC6-14044 Power Commander 6
POWER COMMANDER 6
Installation Guide for: PC6-14044
Model Coverage: 2019-2020 Ducati Scrambler 1100
PARTS LIST
1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS
2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION. THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map
(Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You
can switch on the fl y between these two base maps when you hook up a switch to
the MAP inputs. You can use any open/close type switch. The polarity of the
wires is not important.
Shifter
(Input 1 or 2) Used for clutch-less full throttle upshifts. Insert the wires
from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of
the wires is not important. Set to Input 2 by default.
Speed
If your application has a speed sensor then you can tap into the signal side
of the sensor and run a wire into this input. This will allow you to calculate
gear position in the Control Center Software. Once gear position is setup you
can alter your map based on gear position and setup gear dependent kill times
when using a quick shifter.
Analog
This input is for a 0-5v signal such as engine temp, boost, etc. Once this
input is established you can alter your fuel curve based on this input in the
Power Core software.
Launch You can connect a wire to either Input 1 or Input 2 and then the other
end to a switch. This switch when engaged (continuity) will only allow the RPM
to be raised to a certain limit (set in the software). When released, you will
have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 fi rst remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tighten the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
2
2019-2020 DUCATI SCRAMBLER 1100
INSTALLATION GUIDE
INSTALLING THE POWER COMMANDER 6
Remove the seat the fuel tank.
2 Route the PC6 wiring harness forward along the inside of right frame rail.
3 Attach the ground wire of the PC6 to the negative (-) side of the battery.
4 Unplug
the Crank Position Sensor connector. This is a 3-pin, BLACK connector that
sits on top of the vertical cylinder.
5 Plug the
PC6 in-line of the stock CPS and wiring harness.
6 Remove
the cosmetic cover on the left side of the engine and slide the purge valve
forward to move out of the way.
7 Unplug
the stock wiring harness from the injector.
8 Connect
the YELLOW colored wires of the PC6 in-line of the rear injector and wiring
harness.
9 Put the purge valve back in place and reinstall the cosmetic cover.
10 Remove
the cosmetic cover on the right hand side of the engine.
11 Unbolt the IAC valve to gain access to the injector.
12 Unplug
the stock wiring harness from the front injector.
13 Plug
the ORANGE colored wires of the PC6 in-line of the stock injector and wiring
harness.
14 Unplug
the TPS connector.
This is a 6-pin, BLACK connector on the right hand side of the bike just above
the IAC valve.
15 Plug
the PC6 in-line of the TPS connector.
16 Reinstall the IAC valve and cosmetic cover.
17 Reinstall the fuel tank and the seat.
Download
the latest map fi les from our web site at dynojet.com/tunes.
2191 MENDENHALL DRIVE
NORTH LAS VEGAS, NV
89081 – 800-992-4993 – DYNOJET.COM
© 2019-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>