Dynojet WR450F Power Commander 6 Yamaha Installation Guide
- October 27, 2023
- Dynojet
Table of Contents
POWER COMMANDER 6
Installation Guide for: PC6-22053
Model Coverage: 2012-2014 Yamaha WR450F
Installation Guide
WR450F Power Commander 6 Yamaha
PARTS LIST
1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS| 2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
---|---
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION.
THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map| (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You
can switch on the fl y between these two base maps when you hook up a switch to
the MAP inputs. You can use any open/close type switch. The polarity of the
wires is not important.
---|---
Shifter| (Input 1 or 2) Used for clutch-less full throttle upshifts. Insert
the wires from the Dynojet quick shifter into either Input 1 or Input 2. The
polarity of the wires is not important. Set to Input 2 by default.
Speed| If your application has a speed sensor then you can tap into the signal
side of the sensor and run a wire into this input. This will allow you to
calculate gear position in the Control Center Software. Once gear position is
setup you can alter your map based on gear position and setup gear dependent
kill times when using a quick shifter.
Analog| This input is for a 0-5v signal such as engine temp, boost, etc. Once
this input is established you can alter your fuel curve based on this input in
the Power Core software.
Launch| You can connect a wire to either Input 1 or Input 2 and then the other
end to a switch. This switch when engaged (continuity) will only allow the RPM
to be raised to a certain limit (set in the software). When released, you will
have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 fi rst remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tighten the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
INSTALLING THE POWER COMMANDER 6
1 Remove the seat, the radiator side covers, and the fuel tank.| 2 Secure the
module to the top of the rear fender under the seat in the location shown.
Use the supplied Velcro to secure the module. Clean both surfaces with the
supplied alcohol swab prior to applying the Velcro.
3 Route the PC6 wiring harness down the left hand side of the frame towards
the engine following the stock wiring as closely as possible.
4 Secure the ground wire with the eyelet of the PC6 wiring harness to the
negative terminal of the bike’s battery.
---|---
| 
5 Locate and unplug the stock wiring harness from the fuel injector on top of
the bike’s throttle body.| 6 Plug the PC6 wiring harness in-line of the fuel
injector and the stock wiring harness.
| 
7 Locate and unplug the stock wiring harness from the bike’s Throttle Position
Sensor.
The TPS is located on the left side of the throttle body.| 8 Plug the PC6
wiring harness in-line of the TPS and the stock wiring harness.
| 
9 Locate and unplug the stock wiring harness from thebike’s Crank Position
Sensor.
This connector is located to the left of the frame justbehind the radiator.
You can trace the stock wiring harness coming out of the left side engine
cover to
this connector.| 10 Plug the PC6 wiring harness in-line of the stock wiring
harness and CPS.
| 
11 Locate and unplug the stock wiring harness from the bike’s Ignition Coil.
This connector is on the front left side of the bike just below the radiator.|
12 Plug the PC6 wiring harness in-line of the Ignition Coil and the stock
wiring harness.
13 Reinstall the fuel tank, radiator side covers, and the seat.
| 
Download the latest map fi les from our web site at dynojet.com/tunes.
PUSH THE LIMIT
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081 – 800-992-4993 –
DYNOJET.COM
© 2012-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>