ORION OIC-7002 High Performance Broadcast Rack Mount Monitor User Guide

ORION OIC-7002 High-Performance Broadcast Rack Mount Monitor

All contents of this document may change without prior notice, and actual product appearance may differ from that depicted herein.

Safety Instruction

Follow this safety instruction to use the monitor properly and prevent damage. Keep this user’s guidebook for later use.

Warning

If the user does not follow this instruction, it may cause serious damage to the user.

Cautions

If the user does not follow this instruction, it may cause slight damage to the user or cause some damage to the monitor.

Warning

• Never remove the back over and touch the inside of the monitor. If you need a service, please contact the service centre.
• Keep away the monitor from direct sunlight and a heating appliance.
• Never push objects of any kind into this product as they may result in a risk of fire or electric shock.
• Connect the power code to the wall outlet tightly. If the power code or plug is defective and the wall outlet is not tight, please do not use them.
• Do not install this monitor on the outside and near water. It may cause damage to the product, electric shock and fire.
• For cleaning do not use liquid cleaners. Never touch the power plug with wet hands.
• When lightning and thunder, unplug the monitor from the wall outlet and never touch it. Unplug this product from the wall outlet, when it does not operate for a long time.
• When smoking and noising from the monitor, unplug the product from the wall outlet and contact a service centre.

Cautions

• Install this monitor some distance from the wall and do not install it unless Proper ventilation is provided.
• Place this product on a stable place. If not, it may fall, causing serious Damage to the monitor and people.
• The openings must not be blocked by a curtain, rug or another similar surface.
• When carrying this monitor, be careful not to damage the panel and drop it. It may cause some trouble.
• Before carrying the monitor, turn it off and unplug the signal cables and the power code from the wall outlet.
• Take the power plug out from the wall outlet. Do not pull the cable. It may snap the inner wires and cause overheating and fire.
• Install this monitor about 50cm away from the eyes and an angle of 0~15 degrees below the eyes. Too close installation may cause weak sight.
• Do not press the LCD panel with your hands or the sharpened material hard.
• For cleaning, unplug the monitor from the Wall outlet. Do not use the liquid cloth. Use the soft cloth.
• Do not use the chemical liquid for cleaning. It may cause fading and breakage.

Installation

Parts List

LCD Monitor (1SET), Power Cable (1EA), AC/DC Adaptor (1EA), and User Manual (1EA).

How to Install

First, make sure that the front power button is turned off. If you press the button, a button is locked and power will be turned on. And then press again the button, the button is released and the power will be turned off.

SDI Connection

• Turn off the power button.
• Connect the required cables for video signal input and output.
• Connect the AC power cord’s connector to the AC power connector on the AC/DC adaptor. Connect the 4-pin female XLR connector of the adaptor to the back of the monitor.
• Insert the AC power cord’s plug to an AC outlet (100-240V @ 50/60 Hz).
• Turn on the power button.

1. XLR Connector: 4PIN XLR Connector, 12VDC
2. SDI IN : BNC (75Ω Terminated), SMPTE-424M, SMPTE-292, SMPTE-259M.
3. SDI OUT: BNC (75Ω Terminated), SMPTE-424M, SMPTE-292, SMPTE-259M.
4. GPI: D-SUB15, General Purpose Input.

Notes: #5, #6, #7, #8, #10 pins must be connected to GND.

Service Port: Port for firmware upgrade with Service Card (Optional).

GPI Connection

• Turn off the power button.
• Connect a D-SUB15 connector to a GPI connector.
• Turn on the power button.

Service Card Connection

• Turn off the power button.

• Insert the service card into the service port.

• Turn on the power button.

  • Service Cards are optional.

• Function and Control Key

POWER

• Turn ON/OFF the monitor.
• If you press the button, the button is locked and power will be turned on. And then press again the button, the button is released and the power will be turned off.

BRIGHT

• Adjust visual colour brightness.
• Press Bright Knob, BRIGHT OSD will display on the screen.
  • Rotate it clockwise: Brightness increases
  • Rotate it counterclockwise: Brightness decreases
  • Press it again, and return to the default value (50).
• Adjustable range: 0~100%, default 50.

CONTRAST

• Adjust visual colour contrast.
• Press Contrast Knob, CONTRAST OSD will be displayed on the screen.
  • Rotate it clockwise: Contrast increase.
  • Rotate it counterclockwise: Contrast decrease.
  • Press it again, and return to the default value (80).

CHROMA

• Adjust visual colour chromaticity.
• Press Chroma Knob, CHROMA OSD will be displayed on the screen.
  • Rotate it clockwise: Chroma increase.
  • Rotate it counterclockwise: Chroma decrease.
  • Press it again, and return to the default value (50).
• Adjustable range: 0~100%, default: 50.

ASPECT

• Switch the aspect ratio of the screen.
• Whenever the Aspect button is pressed, the aspect ratio will be switched as follows.
  • 4:3->16:9->OFF.
• Default: OFF.

MENU

• Activate and exit the OSD menu.
• Press the MENU button, OSD menu will be displayed on the screen.
  • Rotate the Chroma knob clockwise: move down.
  • Rotate the Chroma knob counterclockwise: move up.
  • Press the Chroma knob: select a value or enter it into the sub-menu.

SCAN

• Switch the scan mode of the monitor
• Whenever the Scan button is pressed, scan mode will be switched as follows.
  • Normal->Over->Zoom.
• Default: Normal.

MARKER

• Switch the maker of the screen.
• Whenever the Marker button is pressed.
• The marker will be toggled ON/OFF.

CHAR

• Select the user-defined character display.
• Whenever the CHAR button is pressed. User-defined characters will be displayed ON/OFF
• Default: OFF.

WFM

• Select the WFM of the monitor.
• Whenever the WFM button is pressed. WFM will be toggled ON/OFF.
• Default: OFF.

Tally

• Bi-Color (Red/Green).
• Controlled via remote GPI.
• Default: Off

Troubleshooting

When the following troubles have occurred, follow the troubleshooting before contacting a service centre.

The screen doesn’t show up

• Make sure if the power supply is connected properly
• Turn on the power.
• Select the input signal right for the connected port.

The screen is too light or too dark

• Control the BRIGHTNESS

OSD MENU

INFORMATION

| VIDEO FORMAT| Current video format(Display only)
COLOR TEMP| Current colour temperature(Display only)
VERSION| Current firmware version(Display only)

VIDEO

| EXIT| Return to Level 1
APERTURE| ON / OFF, default: OFF
APT LEVEL| 0 ~ 100, default: 80
GAMMA| 1.0 ~ 3.0, default: 2.2
SHIFT H| -128 ~ 127, default: 0
SHIFT V| -128 ~ 127, default: 0
COLOR TEMP| 6500K / 9300K / USER

COLOR TEMP USER

| COPY FROM| 6500K/9300K
RED GAIN| 0.500 ~ 1.992, default: 1.00
GREEN GAIN| 0.500 ~ 1.992, default: 1.00
BLUE GAIN| 0.500 ~ 1.992, default: 1.00
RED BIAS| -128 ~ 127, default: 0
GREEN BIAS| -128 ~ 127, default: 0
BLUE BIAS| -128 ~ 127, default: 0

MODE

| EXIT| Return to Level 1
SCAN| NORMAL / OVERSCAN / ZOOM, default: NORMAL
ASPECT| AUTO / 4:3 / 16:9 /, default: AUTO
MONO/COLOR| RGB / MONO / RED / GREEN / BLUE, default: RGB
HV DELAY| ON / OFF, default: OFF

MARKER

| EXIT| Return to Level 1
MARKER| ON / OFF, default: OFF
CENTER| ON / OFF, default: ON
ASPECT| OFF / 4:3 / 16:9 / 1.85:1 / 2.35:1 / 13:9 / 14:9 / 15:9,

default: OFF

SAFETY| OFF, 80 ~ 99%, USER, default: 80%
CROSS HATCH| OFF / SMALL / MEDIUM / LARGE, default OFF

AUDIO

| EXIT| Return to Level 1
LEFT CHANNEL| 1 ~ 16, default: 1
RIGHT CHANNEL| 1 ~ 16, default: 2
CHANNEL PRESET| LOCK / UNLOCKED, default: UNLOCKED
LEVER METER| ON / OFF, default: OFF
BACKGROUND| ON / OFF, default: OFF
DECAY| FAST / MEDIUM / SLOW, default: MEDIUM
DISPLAY CHANNELS| 1 ~ 16, default: 8
DISP FILTER| ALL / ACTIVE, default: ALL
COLUMNS| DUAL / QUAD, default: DUAL
DISP TPYE| OVERLAY / OVERLAP, default: OVERLAP

WAVEFORM

| EXIT| Return to Level 1
WAVEFORM| ON / OFF, default: OFF
SIZE| SMALL / MEDIUM / LARGE, default MEDIUM
POSITION| LEFT TOP / LEFT BOT / RIGHT TOP / RIGHT BOT,

default RIGHT BOT

DISP TYPE| OVERLAY / OVERLAP, default: OVERLAY

VECTORSCOPE

| EXIT| Return to Level 1
VECTORSCOPE| ON / OFF, default: OFF
SIZE| SMALL / MEDIUM / LARGE, default: MEDIUM
POSITION| LEFT TOP / LEFT BOT / RIGHT TOP / RIGHT BOT,

default: LEFT BOT

DISP TYPE| OVERLAY / OVERLAP, default: OVERLAY

REMOTE

| EXIT| Return to Level 1
PIN 1| R TALLY(fixed)
PIN 2| G TALLY(fixed)
PIN 3| default: R ONLY
 | PIN 4| default: G ONLY
---|---|---
PIN 9| default: B ONLY
PIN 11| default: MONO
PIN 12| default: MARKER
PIN 13| default: ASPECT
PIN 14| default: SCAN
PIN 15| default: HV DELAY

SETUP

| EXIT| Return to Level 1
FORMAT DISPLAY| AUTO / ON / OFF, default: AUTO
TIMECODE| OFF / LTC / VITC1 / VITC2, default: OFF
KEY LOCK| LOCK / UNLOCK, default: UNLOCK
PICTURE DEALY| NORMAL / FAST / FASTEST, default: NORMAL
BACKLIGHT| 0% ~ 100%, default 80%
CHARACTER DISPLAY| ON / OFF, default: OFF
LOCATIONS| CENTER TOP / CENTER BOTTOM,

default: CENTER TOP

ENTER| USER ASSIGN
SIZE| SMALL / LARGE, default: SMALL
COLOR| YELLOW / RED / BLACK, default: YELLOW
FACTORY DEFAULT| PROCEED / CANCEL, default: CANCEL
RESTORE USER CONFIG| PROCEED / CANCEL, default: CANCEL
LOAD USER CONFIG| PROCEED / CANCEL, default: CANCEL

Features

OIC-5003| OIC-7002|
---|---|---

DISPLAY

INPUT

OUTPUT

Supported Video format

General

AC/DC

Adaptor

| LCD| TFT-LCD(IPS)| TFT-LCD|
Active Area(mm)| 108.02×64.8, 5″(Diagonal Wide)| 152.4×91.44 7.0″(Diagonally)|
Resolution| 800(H)x480(V)| 800(H)x480(V)|
Pixel Pitch(mm)| 0.135(H)x0.135(V)| 0.1905(H)x0.1905(V)|
Color Depth| 16.7M, 24bit true color| 16.7M, 24bit true color|
Luminance(cd/m2)| 250(min:100)| 400(min:250)|
Contrast Ratio

SMPTE-424M

| 500:1| 1000:1|

1xBNC

|

1xBNC

|
SMPTE-292|
SMPTE-259M

SMPTE-424M

|

1xBNC(Loop through)

|

1xBNC(Loop through)

|
SMPTE-292|
SMPTE-259M

SMPTE 425M-AB

|
1080p(60/59.94/50)| 1080p(60/59.94/50)|

SMPTE 274M

|

1080i(60/59.94/50)

1080p(30/29.97/25/24/23.98)

1080PsF(30/29.97/25/24/23.98)

|

1080i(60/59.94/50)

1080p(30/29.97/25/24/23.98)

1080PsF(30/29.97/25/24/23.98)

|
SMPTE 296M| 720p(60/59.94/50/30/

29.97/25/24/23.98)

| 720p(60/59.94/50/30/

29.97/25/24/23.98)

|
SMPTE 125M| 525i(NTSC, 480i60)| 525i(NTSC, 480i60)|
ITU-R BT.601

Power

| 625i(PAL, 575i50)| 625i(PAL, 575i50)|
10~19VDC| 10~19VDC|
Power Consumption(W)|

Approx. 28.8W(12V,2.4A)

|

Approx. 26.4W(12V,2.2A)

|
ACOperating

Temperature ℃)

| 0℃~40℃| 0℃~40℃|
Operating

Humidity (%)

| 30%~85%(Non-Condensing)| 30%~85%(Non-Condensing)|
Storage Temperature(℃)| -20℃~60℃| -20℃~60℃|
Storage Humidity

(%)

| 0%~90%| 0%~90%|
Weight(Kg)| 1.8kg| 2.1kg|
Dimension (WxDxH, mm)

Input

|

481×82.3×88.1, 2U

|

481×82.3×132.6, 3U

|
100~240VAC, 50/60Hz, 1.7A| 100~240VAC, 50/60Hz, 1.7A|
Output| 12VDC, 4.6A| 12VDC, 4.6A|

Dimension[Units :mm] for OIC-5003

Mechanical Drawing

Dimension[Units :mm] for OIC-7002

Warranty

2-Year Limited Warranty

ORION Images Corporation. carries a limited warranty from ship date against defects in materials and workmanship. ORION Images Corporation. is not liable for improper installation that results in damage to mounts, adapters, display equipment or personal injury.  Contact ORION Images Corporation. In the event of missing and/or damaged equipment, or technical questions, the following information can help in the completion of the installation.

• Address: 7300 Bolsa Avenue, Westminster C A 92683
• Tel: (714)766-6300 /
• Fax: (714)766-6310
• Email: rma@orionimages.com
• Website: http://www.orionimages.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>