Orion Motor Tech V20230614 Bearing Seal Installation Driver Kit User Manual

Orion Motor Tech V20230614 Bearing Seal Installation Driver Kit

Safety Information

DANGER!

• The instructions provided herein are only for general information. ALWAYS perform all repairs in full compliance with your vehicle’s service manual. After any repair, test your engine and vehicle in your workshop and at low speed before returning to normal use. Failure to do so may result in serious property damage and severe personal injury.
• DO NOT allow children or those unfamiliar with this product and its compatible brake systems to use it. Do not use while under the influence of alcohol, drugs, or any medication that negatively affects your judgment or reflexes. Keep children and bystanders away during use.
• Keep your work site clean and well lit. Cluttered and dark work areas invite accidents.
• For best results, keep the kit clean and dry. Remove any fluid, oil, or grease before and after work, particularly from the handle and fittings.
• ALWAYS use personal protective equipment (PPE) suitable to your task. Always wear ANSI-approved eye and hand protection while using this product. Nonslip footwear is also highly recommended. Other equipment such as ear, head, and body protection may also be necessary depending on your work and other equipment.
• Dress properly for automotive servicing. Do not wear loose clothing or jewelry and keep hair, clothing, gloves, hoses, and tools away from any moving parts during use.
• ALWAYS know and understand the specific safety warnings and instructions for your vehicle before using this kit. Use the correct fluids, pressures, adapters, etc. for your vehicle. Make sure the parking brake is activated before beginning any work. Use with jack and jack stands able to fully support the necessary weight. Never touch any heated surface with exposed skin.
• Do not overreach. Keep proper footing and balance at all times.
• DO NOT use excessive pressure with this product and do not force it or its attachments.
• Maintain this product. Check for misalignment, binding, wear, or other damage before use.
  If any damage is detected, repair or replace the problematic components before further use.
  In a large shop, mark such tools DO NOT USE until they have been repaired. Only replace components with identical parts.

Specifications

Package List

Handles × 3
Metric Drivers × 14
Imperial Drivers × 16

Operation

Installation

1. Choose the appropriate driver from the kit, selecting one that matches the outer diameter of the seal you are working with. Attach it to the appropriate handle.
2. Prior to installation, apply a thin layer of suitable lubricant (not included) to the outer edge of the seal Position the seal onto the shaft or housing where you want to install it, ensuring proper alignment and an even placement.
3. Hold the tool handle firmly and align the driver with the center of the seal. With a controlled and steady grip, apply gentle and even pressure on the driver using the handle. Use a hammer to tap the handle slowly, driving the seal into place. Ensure the it is fully inserted and seated correctly.
4. After installation, carefully inspect the seal to verify that it is properly seated. Check for any misalignment, gaps, or irregularities. Verify that the seal is secure and does not move when lightly pushed or rotated. If you have additional seals to install, repeat the process for each one, using the appropriate driver size for each component.

Removal

1. Choose the appropriate driver from the kit, selecting one that matches the outer diameter of the seal you are working with. Attach it to the appropriate handle.
2. Place the driver against the inner edge of the component and gently tap the handle with a hammer to dislodge it from the shaft or housing. Repeat the process for each one, using the appropriate driver size for each component.

Maintenance

• Clean the tools with a soft damp cloth using a mild detergent or solution after use. Do not rinse them or use abrasive cleaners or caustic chemicals.
• For best results, lubricate the tools with high-quality anti-corrosive oil between uses.
• Check the tools periodically for any wear or damage. Repair or replace any problematic parts before further use.
• If the tools will not be used for an extended period of time, clean and lubricate them and store them in a cool dry place inaccessible to children.

Contact Us

Thank you for choosing our products! If you have any questions or comments, contact us at support@orionmotortech.com and we’ll resolve your issue ASAP!

For a .pdf copy of the latest version of these instructions, use the appropriate app on your smartphone to scan the QR code to the right.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>