ORION 9RCHARD 9.7 Inch Rack Mount Ready Dual Display LED Monitor User Guide
- June 17, 2024
- Orion
Table of Contents
- ORION 9RCHARD 9.7 Inch Rack Mount Ready Dual Display LED Monitor
- FAQ
- SAFETY INSTRUCTION
- FCC RF INTERFERENCE STATEMENT
- INSTALLATION
- SHORT KEY FUNCTION
- CONNECTION
- OSD MENU SETTING
- HOT KEY Function Definition
- FEATURE
- APPENDIX
- Warranty
- TROUBLESHOOTING
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ORION 9RCHARD 9.7 Inch Rack Mount Ready Dual Display LED Monitor
Specifications
- Product Name: RACK MOUNT READY SERIES (9.7 inches Dual Monitor)
- Manufacturer: Orion Images
- Website: http://www.orionimages.com
Installation and User’s Guide
1. Safety Instruction
Follow the safety instructions below to use the monitor properly and prevent damages:
Warning
- Never remove the back cover and touch the inside of the monitor. If you need service, please contact the service center.
- Keep the monitor away from direct sunlight and heating appliances.
- Never push objects of any kind into this product as it may result in a risk of fire or electric shock.
- Connect the power cord tightly to the wall outlet. If the power cord or plug is defective or the wall outlet is loose, do not use them.
Caution
- Do not install this monitor outside or near water as it may cause damage, electric shock, and fire.
- Do not use liquid cleaners for cleaning. Never touch the power plug with wet hands.
- When there is lightning and thunder, unplug the monitor from the wall outlet and avoid touching it.
- Unplug this product from the wall outlet when it is not in use for a long time.
- If there is smoking or noise coming from the monitor, unplug it from the wall outlet and contact a service centre.
FAQ
- Q: Can I remove the back cover of the monitor?
- A: No, removing the back cover may cause damages and void the warranty. If you require service, please contact the authorized service center.
- Q: Can I use liquid cleaners to clean the monitor?
- A: No, liquid cleaners should not be used for cleaning. Unplug the monitor and use a soft cloth instead.
- Q: How far should I install the monitor from my eyes?
- A: It is recommended to install the monitor about 50cm away from your eyes.
- Q: Can I use the monitor near water?
- A: No, it is not recommended to install the monitor outside or near water to prevent damage, electric shock, and fire.
SAFETY INSTRUCTION
Follow this safety instruction to use the monitor properly and prevent the damages.
This safety instruction has “Warning” & “Caution” as below
- Warning – If the user does not follow this instruction, it may cause serious damage to the user.
- Caution – If the user does not follow this instruction, it may cause the slight damage to the user or cause some damage to the monitor.
Keep this user’s guidebook for later use.
Warning
WARNING: How to fix
- Do not open this product as it contains high voltage inside.
- It may create an electric shock.
- It the user disassembles and removes the back cover, it does not make sure to make up for the damages and do a service and exchange the monitor.
Cautions
FCC RF INTERFERENCE STATEMENT
NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio, TV technician for help.
- Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment.
DOC COMPLIANCE NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the radio interference regulation of Canadian Department of Communications.
INSTALLATION
Parts
How to Install
KEY BUTTON
SHORT KEY FUNCTION
OSD Key Function
MENU / EXIT| Activates and exits the OSD
SOURCE /| Select the input source, and move the OSD menu
AUTO /| Move the OSD menu and adjust of RGB source
VOL| Decrease the level of volume and move the previous menu.
SELECT| Increase the level of volume and select the OSD menu
| Turns the power ON or OFF. There will be a few seconds delay before the
display appears. The power LED(next to the power switch) lights with green
when the power is turned ON.
The power is turned off by pressing the power switch again and the power LED goes Red.
LED LAMP| Power ON Indicator
CONNECTION
- HDMI Input
- RGB Input
- AV1 Input / Output
- Composite signal in / out for AV 1
- AV21 Input / Output
- Composite signal in / out for AV 2
- AUDIO1 Input
- Stereo audio signal input. This input for AV1 and S-VIDEO
- S-Video Input
- Y/C separated signal input
- PC AUDIO Input
- DC 12V Input
OSD MENU SETTING
INPUT Select
Inputs can be set to AV1, AV2, S-VIDEO, HDMI and PC mode.
- Press the SOURCE button and then ▲/▼ Button to move the source
- Press the ►button to select the source
- Press the MENU/EXIT Button to exit the INPUT menu.
MENU Selection
- Press the MENU/EXIT key to access the main menu.
- Use the ▲ and ▼ arrow key to highlight a selection.
- Press the ►/SELECT key to select an item
- Use the ▲ and ▼ arrow key to highlight a selection.
- Use the and ►arrow key to adjust the setting on a selected item.
PICTURE MENU on OSD
INPUT SOURCE (AV1, AV2, S-VIDEO, HDMI)
OSD Menu is working on after it connects the source signal.
- Press the MENU/EXIT ► Button and then / ► Button to select the PICTURE menu.
- Press the ▲ or ▼ Button and then button to select the Button to select the adjustment item you need.
- ►Press the or ►Button to activate the item. Ex) if you select the BRIGHTNESS, then the below picture appears on the bottom screen.
- Press the MENU/EXIT button to move to the previous menu.
INPUT SOURCE (PC Mode only)
- Press the MENU/EXIT ► Button and then / ► Button to select the PICTURE menu.
- Press the ▲ or ▼ Button and then button to select the Button to select the adjustment item you need.
- Press the or► Button to active the item.
- Auto’ function adjusts the location of the screen by receiving the sync signal from PC. Ex) Resolution change
- Colour Auto’ adjusts the optimum color coordination automatically.
VOLUME MENU on OSD
AV1, AV2, S-VIDEO, PC, HDMI
- Press the /SELECT button to adjust the volume up and down.
SYSTEM MENU on OSD
AV1, AV2, S-VIDEO, PC, HDMI
- Press the MENU/EXIT ► Button and then / ► Button to select the PICTURE menu.
- Press the ▲ or ▼ Button and then button to select the Button to select the adjustment item you need.
- Press the or ►Button to activate the item.
- Sleep Timer ‘ function is to adjust the time to turn the power off automatically.
- The duration function adjusts the time to display the OSD menu.
- Halftone’s function is to adjust the transparency of the OSD menu.
- DPMS’ function is to adjust the time to turn power off during no input signal.
[Option]
‘No Operation’ function is adjust the time to turn power off during no input key button.
FUNCTION MENU on OSD
PC Mode only
- Press the MENU/EXIT ► Button and then / ► Button to select the PICTURE menu.
- Press the ▲ or ▼ Button and then button to select the Button to select the adjustment item you need.
- Press the or►Button to active the item.
- Press the MENU/EXIT button to move to the previous menu.
HOT KEY Function Definition
OSD Key Function
MENU / EXIT| OSD ON / OFF, Exit
MODE / DOWN| Source Change, Menu down
►VOL+ / RIGHT| Volume menu On / Volume Up
VOL- / LEFT| Volume Down
AUTO / UP| Auto Adjust, Menu up
POWER| POWER ON / OFF
FEATURE
Display
Screen Size| 9.7 Inch
Panel Type| LED BLU
Max. Resolution| 1024 x 768 @ 60Hz
Pixel Pitch| 0.192 x 0.192 mm
Brightness| 400cd/m2
Contrast Ratio| 800 : 1
Aspect Ratio| 4 : 3
Viewing Angle (H/V)| 178 / 178
Display Color| 262,144 Colors (6 bit)
Response Time| < 35ms
Video System| NTSC / PAL
Interface
Video In / Out (BNC Type)| 2 / 2 x Dual Monitor
HDMI In| 1 x Dual Monitor
S-Video In| 1 x Dual Monitor
VGA In (15 PIn D-Sub)| 1 x Dual Monitor
Audio In (RCA Type)| 1 x Dual Monitor
PC Stereo In| 1 x Dual Monitor
Audio
Built-In Speaker| Yes
Dimension / Weight
Dimension| 18.98″ x 8.66″ x 1.97″
Net. Weight| 5.2 kg (11.46 lbs)
Power
Consumption: < On| < 35W
Electrical Ratings
| AC100 ~ 240V (50/60Hz)
DC12V / 3A
APPENDIX
D-SUB Connector PIN Assignment
PIN No. PIN Name PIN No. PIN Name
1| RED VIDEO| 9| NC
2| GREEN VIDEO| 10| SIGNAL CABLE DETECT
3| BLUE VIDEO| 11| GROUND
4| GROUND| 12| SDA (for DDC)
5| GROUND| 13| H-SYNC
6| RED GROUND| 14| V-SYNC
7| GREEN GROUND| 15| SCL (for DDC)
8| BLUE GROUND| |
HDMI Type A PIN Assignment
PIN No. | PIN Name | PIN No. | PIN Name |
---|---|---|---|
1 | TMDS Data2+ | 11 | TMDS Clock Shield |
2 | TMDS Data2 Shield | 12 | TMDS Clock- |
3 | TMDS Data2- | 13 | CEC |
4 | TMDS Data1+ | 14 | Reserved (HDMI 1.0-1.3c), HEC Data – |
5 | TMDS Data1 Shield | 15 | SCL (PC serial Clock for DDC) |
6 | TMDS Data1- | 16 | SDA (PC serial Clock for DDC) |
7 | TMDS Data0+ | 17 | DDC/CEC/HEC Ground |
8 | TMDS Data0 Shield | 18 | +5V Power (max 50 mA) |
9 | TMDS Data0- | 19 | Hot Plug Detect (All Versions) and HEC Data +(Optional, |
HDMI 1.4+ with Ethernet)
10| TMDS Clock+
Warranty
Year Limited Warranty
All ORION IMAGES products carry a limited warranty from ship date against defects in materials and workmanship. ORION IMAGES is not liable for improper installation that results in damage to mounts, adapters, display equipment or personal injury. Contact ORION IMAGES In the event of missing and/or damage equipment, or technical questions, the following information can help in the completion of the installation.
ORION IMAGES Corp. (USA)
- Address: 7300 Bolsa Avenue, Westminster, CA 92683
- Tel: 714-766-6300 /
- Fax: 714-766-6310
- mail: rma@orionimages.com
- Website: http://www.orionimages.com
TROUBLESHOOTING
- When the following troubles have occurred, follow the troubleshooting. Before contacting a service centre.
Troubleshooting | Troubleshooting Tip |
---|
The screen doesn’t show up
| 1. Make sure if the power supply is connected property
2. Turn on the power.
3. Select the input signal right for the connected port.
The screen is too light or to dark|
Control the BRIGHTNESS
The screen size is not fit for the PC signal| Press the AUTO key among keys in
the front. (It is used only in the PC signal)
The screen color shows strange in the PC signal| In the FUNCTION menu of OSD
menu, perform the AUTOADJUST.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>