VIDEOTEC VIPNX Stainless Steel Wiper Kit Instruction Manual
- June 17, 2024
- VIDEOTEC
Table of Contents
VIDEOTEC VIPNX Stainless Steel Wiper Kit Instruction Manual
About this manual
Before installing and using this unit, please read this manual carefully. Be sure to keep it handy for later reference.
Typographical conventions
DANGER!
High level hazard.
Risk of electric shock. Disconnect the power supply before proceeding with any
operation, unless indicated otherwise
WARNING!
Medium level hazard.
This operation is very important for the system to function properly. Please
read the procedure described very carefully and carry it out as instructed.
INFO
Description of system specifications. We recommend reading this part carefully
in order to understand the subsequent stages
Notes on copyright and information on trademarks
The quoted names of products or companies are trademarks or registered trademarks
Safety rules
****The manufacturer declines all responsibility for any damage caused by an improper use of the appliances mentioned in this manual. Furthermore, the manufacturer reserves the right to modify its contents without any prior notice. The documentation contained in this manual has been collected with great care, the manufacturer, however, cannot take any liability for its use. The same thing can be said for any person or company involved in the creation and production of this manual.
- The device must be installed only and exclusively by qualified technical personnel.
- Before any technical work on the appliance, disconnect the power supply.
- Do not use power supply cables that seem worn or old.
- Never, under any circumstances, make any changes or connections that are not shown in this handbook: improper use of the appliance can cause serious hazards, risking the safety of personnel and of the installation.
- Use only original spare parts. Not original spare parts could cause fire, electrical discharge or other hazards.
- Before proceeding with installation check the supplied material to make sure it corresponds to the order specification by examining the identification labels (“4.2 Product markings”, page 2).
Identification
Product description and type designation
Wiper kit which can be directly installed on the housing body. Wiper lade and enclosure constructed from AISI 316 stainless steel. It includes the support for the pump washing injector. Available in 24Vac and 230Vac versions, 7W max. Available for NXM, NXL, NXJ series housings.
Product markings
See the label attached to the outside of the package.
Preparing the product for use
****Any change that is not expressly approved by the manufacturer will invalidate the guarantee
Contents and unpacking
When the product is delivered, make sure that the package is intact and that
there are no signs that it has been dropped or scratched.
If there are obvious signs of damage, contact the supplier immediately.
Keep the packaging in case you need to send the product for repairs.
Check the contents to make sure they correspond with the list of materials as
below:
- Stainless steel wiper kit
- Instructions manual
Safely disposing of packaging material
The packaging material can all be recycled. The installer technician will be responsible for separating the material for disposal, and in any case for compliance with the legislation in force where the device is to be used.
Bear in mind that if the material has to be returned due to a fault, using the original packaging for its transport is strongly recommended.
Assembling and installing
****Only specialized personnel should be allowed to assemble and install the device.
Installation
****Before carrying out any operation remember to disconnect the product from the power supply
****For the version powered at 230Vac it is necessary to insert a monopolar 1 0 switch(open contact distance d >3 mm) upstream of the appliance. This switch should be used to disconnect the power supply before carrying out any maintenance or opening the appliance
Glass window replacement (only for NXM housing)
To install the kit on the NXM housing the standard glass window should be
replaced with the special one supplied with the kit.
Remove the front flange (01) on the housing by unscrewing the 4 screws (02).
Replace the standard glass (03) with the special glass (04) and insert it in
its special seating on the flange.
Reassemble the flange on the housing taking care to insert the related seals
(05) correctly in their appropriate housing.
Fasten the front flange to the housing body by tightening the 4 screws.
Installing the wiper kit on NXJ housing
Position the wiper under the housing so that slots on the body correspond with
the fastening pins.
Fasten the wiper body to the housing by screwing the nuts onto the fastening
pins.
Assemble the wiper blade on the output shaft, fixing it in the rest position
on the left side of the glass front.
Installing the wiper kit on NXL and NXM housing
Insert the open metal fastening band through the 2 slots on the wiper body as
shown in the drawing.
Position the wiper body (Fig. 3) by passing the band round the housing body.
Tighten the band with a screwdriver, locking the wiper body
Assemble the wiper blade on the output shaft, fixing it in the rest position
on the left side of the glass front.
If necessary adjust the fastening band to set the position of the wiper body
so that it does not interfere with the housing support. In this way assembly
is adaptable to the orientation of the housing
Installing the optional nozzle kit (only for NXL housing)
Undo the nut (01) from the coupling, insert it into the pipe (02) and insert
the end of the pipe on the kneecap (03).
Lock the nut to the coupling.
Remove one of the 2 sunshield fastener screws (01) located on the front of the
housing. Slide the tube (02) inside the clip (03) and use the screw (01) and
washer (02) to fasten in place.
To adjust the jet direct the nozzle towards the glass of the housing
Wiring
Make sure the power supply voltage used is the same as that shown on the plate
on the back of the appliance.
Make the electrical connections on the female 3+PE connector as shown in the
electrical diagram.
Power the wiper by connecting the phase to terminal 03 (SW) on the connector, neutral to terminal 02 (COM) on the connector and earth to the EARTH terminal.
Use an external button to connect the phase to terminal 01 (PERM) on the
connector.
Keeping the external button pressed will cause continuous operation
(permanent) of the wiper. Releasing the button will take the wiper blade back
to the rest position on the left of the housing window.
If a receiver is used, connect terminal 03 on the connector to output SW on
the receiver, 01 to PERM and 02 to COM.
Connect the tube of the water supply system to the spray nozzle of the wiper
blade and fix it using the plastic hose clamp supply for this purpose.
Instructions for normal operation
****Do not use the wiper when the outside temperature is below 0°C or in case of ice.
Disposal of waste materials
This symbol mark and recycle system are applied only to EU countries and not applied to the countries in the other area of the world.
Your product is designed and manufactured with high quality materials and components which can be recycled and reused
This symbol means that electrical and electronic equipment, at their end-of-
life, should be disposed of separately from your household waste.
Please dispose of this equipment at your local Community waste collection or
Recycling center.
In the European Union there are separate collection systems for used
electrical and electronic products.
Technical data
Wiper lade and enclosure constructed from AISI 316 stainless steel
Dimensions (Axle): 100x169mm (3.9×6.6in), not comprehensive of blade
Connector 3+1 pins
IN 230Vac, consumption 7W max
IN 24Vac, consumption 7W max
Unit weight: 1.7kg / 3.7lb
IP66/67
Technical drawings
****The values are in millimeters.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>