QualGear QG-PM-002-WHT-S Projector Ceiling Mount Accessory Installation Guide
- June 17, 2024
- QualGear
Table of Contents
QualGear QG-PM-002-WHT-S Projector Ceiling Mount Accessory
Product Information
Specifications
- Product Name: QG-PM-002-WHT-S PROJECTOR CEILING MOUNT
- Maximum Rated Weight: 13.5kg (29.7lbs)
- Version: September 2018
Product Usage Instructions
Installation Precautions
Before starting the installation, please read the entire installation manual and make sure to adhere to the following precautions:
- Do not exceed the maximum rated weight specified. Exceeding the weight limit may result in serious injury or property damage.
- Do not begin installation until you have read and understood all the instructions and warnings in the manual.
- This product should only be installed by someone with good mechanical aptitude, experience with basic building construction, and a full understanding of the instructions.
- Improper installation may cause damage or serious injury. QualGear is not liable for the improper use or installation of its products.
- Tighten screws firmly, but avoid over-tightening to prevent damage.
- All QualGear products are intended for indoor use only. Outdoor use voids the limited warranty.
- All QualGear products are designed and tested for residential use only. Commercial use voids the limited warranty.
- If mounting to wooden studs, make sure to anchor the mounting screws into the centre of the studs. Use of an edge-to-edge stud finder is recommended.
- Never exceed the maximum rated weight specified in the manual.
- Ensure that the supporting surface can safely support the combined load of the equipment and all attached hardware and components.
- Follow the designated points in the installation instructions to prevent property damage and personal injury.
- Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
- Avoid installing near air conditioner vents or in areas with excessive dust or smoke.
- When drilling holes in the ceiling, take care to avoid electrical cables, water, or gas pipes in the ceiling.
- This product is designed to be installed on wooden studs, wooden beams, solid concrete, brick, or other specified ceiling constructions.
Parts Checklist
Before starting assembly and installation, please check that all parts listed below are included. If any parts are missing or damaged, contact your local distributor or support@qualgear.com for replacement parts. Do not start assembly until you have received all the parts.
- Ceiling Plate with Connector A (x1)
- Hardware Package
- Projector Mounting Bracket B (x1)
- Marking Template C (x1)
- M3x20 (x4) M-A
- M4x25 (x4) M-B
- M5x25 (x4) M-C
- M6x25 (x4) M-D
- D3 Washer (x4) M-E
FAQ
- Q: Can I exceed the maximum rated weight specified?
- A: No, exceeding the maximum rated weight can result in serious injury or property damage. Always adhere to the weight limit specified in the manual.
- Q: Can I install this product outdoors?
- A: No, all QualGear products are intended for indoor use only. Outdoor use voids the limited warranty.
- Q: Can I use this product for commercial purposes?
- A: No, all QualGear products are designed and tested for residential use only. Commercial use voids the limited warranty.
- Q: What should I do if I have questions about the installation instructions?
- A: For US customers, please contact QualGear customer support via email at support@qualgear.com. For international customers, please contact your local distributor.
- Q: How should I anchor the mounting screws if I’m mounting to wooden studs?
- A: Make sure to anchor the screws into the centre of the wooden studs. It is highly recommended to use an edge-to-edge stud finder for accurate placement.
NOTE: Please read the entire installation manual before you start installation and assembly.
WARNING
- Do not begin to install your QualGear product until you have read and understood all the instructions and warnings contained in this installation manual. If you have any questions regarding the instructions, for US customers please contact QualGear customer support via email at support@qualgear.com. For all international customers, please contact your local distributor.
- This product should only be installed by someone of good mechanical aptitude, who has experience with basic building construction, and who fully understands these instructions.
- This product was designed to be installed and utilized only as specified in this manual. Improper installation of this product may cause damage or serious injury. QualGear is not liable for the improper use or installation of its products.
- Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
- Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
- Tighten screws firmly, but do not over-tighten. Over-tightening can damage the items, greatly reducing their holding power.
- ALL QUALGEAR products are intended for indoor use only and any outdoor use voids the limited warranty.
- ALL QUALGEAR products are designed and tested for residential use only and any commercial use voids the limited warranty.
- For warranty information, please visit http://www.qualgear.com/warranty.php.
- If mounting to wooden studs, make sure that mounting screws are anchored into the centre of the studs. Use of an edge-to-edge stud finder is highly recommended.
- Never exceed the maximum rated weight specified in this manual.
- All bolts and screws must be used at the designated points in the installation instructions to prevent property damage and/or personal injury.
- DO NOT install near air conditioner vents or where there is excessive dust or smoke.
- When drilling holes in the ceiling, it is very important to take care of electrical cables, water, or gas pipes in the ceiling.
This product was designed to be installed on the following ceiling construction only:
CEILING CONSTRUCTION
- Wooden Stud
- Wooden Beam
- Solid Concrete
- Brick
- Other
HARDWARE REQUIRED
- Included
- Included
- Included
- Included
- Contact Qualified Professional
Parts Checklist
IMPORTANT: Before starting installation, please check that all parts shown in this checklist are included. If any parts are missing or damaged, contact your local distributor or support@qualgear.com for replacement parts and do not start assembly and installation until you receive all the parts.
Hardware Package
Cable Management
- Feed the projector cable(s) through the top of the Ceiling Plate.
OR
- Feed the projector cable(s) through the side of the Ceiling Plate.
Mounting to a Wooden Ceiling
NOTE: For concrete ceiling mounting, follow Step 2b.
- Using an edge-to-edge stud finder, find the edges of the stud.
- Using a straight edge, mark the centerline of the stud.
- Using the marking template provided, mark two holes for drilling on the centerline of the stud.
- Using a power drill and 3/16″ drill bit, drill pilot holes of 3/16″ (4.5 mm) diameter and at least 2.5″ (65 mm) depth.
TIP
- Depending on the direction of the studs, choose the mounting holes accordingly.
NOTE: Do NOT use a power drill and do NOT over-tighten the lag bolts.
- Using a socket wrench, mount the ceiling plate and fasten it with the provided lag bolts (W-A) and D6 washers (W-C).
WARNING
- Installers are responsible for providing hardware for other types of mounting situations.
- Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
Mounting to 2b a Concrete Ceiling
- Hold the marking template provided against the ceiling where you want to install the projector and mark four holes for drilling.
- Using a power drill and a 3/8″ masonry drill bit, drill mounting holes of 3/8″ (10 mm) diameter and 2.7″ (70 mm) depth at the marked locations in the previous step.
- Place plastic anchors (W-B) in each hole. Tap each anchor flush with the ceiling using a hammer. Using a socket wrench, mount the ceiling plate and fasten it with the provided lag bolts (W-A) and D6 washers (W-C).
WARNING
Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
Installing Projector Mounting Bracket to the Projector
TIP: Depending on your projector, you may use one of the combinations above.
Align the holes of extension brackets over the mounting holes of the projector, select appropriate screws (M-A/ M-B/ M-C/ M-D) and washers (M-E/ M-F/ M-G/ M-H). Place the bottom spacer (M-L) in between the brackets and the projector. Optional: for mounting to recessed holes only, choose the appropriate spacer (M-I/ M-J/ M-K) in addition to the 5mm spacer (M-L).
Installing the Projector Ceiling Mount Assembly
Align the Projector Mount Assembly to the Ceiling Plate with the Connector, then using the Alley Key (M-P), attach them with the provided Screws (M-M), Washers (M-N), and Plastic Washers (M-O).
NOTE: This mount allows pitch and roll adjustments for a perfect viewing experience.
Adjustments
IMPORTANT!
Do not loosen screws all the way when making adjustments, this will disconnect
the parts and may cause injury or property damage.
- Your projector ceiling mount is now installed.
- To make adjustments, loosen up the screws slightly with the alley key (M-P). When you are satisfied with the adjustments, tighten up the screws again.
Maintenance
Please check that the projector mount is secure and safe to use at regular intervals. If you have any questions regarding any of the instructions or warnings, please contact your local distributor (OR) contact QualGear technical support via email at support@qualgear.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>