FLASH F7100577 Moving Head 12R Light User Manual

: June 17, 2024
: FLASH

Table of Contents

FLASH F7100577 Moving Head 12R Light
Product Information
Specifications
Product Usage Instructions
FAQ
INTRODUCTION
SAFETY INFORMATION
PRODUCT INFORMATION
INSTALATION
CONNECTION
DMX CHART
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FLASH F7100577 Moving Head 12R Light

FLASH-F7100577-Moving-Head-12R-Light-PRODUCT

Product Information

Specifications

Strobe: Shut with many kinds of strobe
Frost filter: 2x frost filter
Operating modes: DMX512, Manual, Auto, Sound-controlled, Master/Slave
DMX channel mode: 16
IP Rating: IP20
Housing material: ABS
Cooling: Active
AC IN/OUT: PowerCon
3-Pin XLR DMX Input/Output
Net Weight: 12.2 kg
Net Dimensions: H(51)xW(28)xD(32) cm
Case Weight: 43.2 kg
Case Dimensions: H(61)(wheel 72)xW(66)xD(35) cm

Installation

Unpack the fixture and check for any transportation damage.
Ensure that the voltage and frequency of the power supply match the power requirements of the fixture.
Ground the yellow/green conductor to earth to avoid electric shock.
Use the provided safety chain when fixing the fixture.
Handle the fixture by taking its base, not just its head.
If there is any visible damage to the housing, it must be replaced.
Do not expose the fixture to rain or moisture to prevent electrical shock or fire.

Connection

Ensure that the fixture is securely fastened to a surface or rigging hardware before applying power.
Use two clamps to rig the fixture, and do not hang it from only one clamp.
Lock each clamp with both 1/4-turn fasteners by turning them a full 900 clockwise.
When clamping the fixture to a truss or other structure at any angle other than with the yoke hanging vertically downwards, use two clamps of half-coupler type.
Do not use any type of clamp that does not completely encircle the structure when fastened.

DMX Chart

The DMX chart for the Moving Head 12R is not provided in this user manual. Please refer to the separate DMX chart documentation for more information on controlling the fixture through DMX.

Product Usage Instructions

Ensure that the fixture is properly installed and connected according to the instructions provided in the Installation and Connection sections.
Refer to the separate DMX chart documentation for information on controlling the fixture through DMX.
To use the fixture in Manual mode, set the desired settings using the control panel or buttons provided on the fixture.
In Auto mode, the fixture will automatically run pre-programmed patterns or sequences.
In Sound-controlled mode, the fixture will react to sound or music by changing its patterns or movements.
In Master/Slave mode, multiple fixtures can be linked together, with one acting as the master and others following its movements or patterns.
Refer to the user manual for specific instructions on using each mode and accessing different features or settings.

FAQ

Q: Can I connect the fixture to a dimmer pack?

A: No, do not connect the device to any dimmer pack.

Q: What should I do if there is a serious operating problem?

A: Stop using the fixture immediately and do not try to repair it yourself. Contact the nearest authorized technical assistance center for repairs.

Q: Can I look directly at the light spot while the fixture is on?

A: No, it is not recommended to look directly at the light spot while the fixture is on.

WARNING! The Moving Head 12R has a powerful pan and tilt motor. The torque reaction when the head is panned suddenly can cause the base to move if the fixture is standing unsecured on a surface. Do not apply power to the 12R unless the baase is securely fastened to a surface or to rigging hardware.
WARNING! Use 2 clamps to rig the fixture. Do not hang the fixture from only one clamp. Lock each clamp with both 1/4-turn fasteners. Fasteners are locked only when turned a full 900 clockwise.
WARNING! When clamping the fixture to a truss or other structure at any other angle than with the yoke hanging vertically downwards, use two clamps of half-coupler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
WARNING! Position or shade the head so that the front lens will not be exposed to sunlight or any other strong light source from any angle – even for a few seconds. See Figure 1. The 12R lens can focused the sun’s rays, creating a potential fire hazard and causing damage.
IMPORTANT! Do not point strong light output from other fixtures at the 12R, as intense illumination can damaged the display.

FLASH-F7100577-Moving-Head-12R-Light-FIG-1

INTRODUCTION

THANK YOU FOR PURCHASING 12R. FOR SAFETY REASONS AND TO ENSURE THE TROUBLE- FREE OPERATION, CAREFULLY READ THE INSTRUCTIONS.

SAFETY INFORMATION

Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruc-tion booklet.
Unpack and check carefully the-re is no transportation damage be-fore using the fixture.
Before operating, ensure that the voltage and frequency of po-wer supply match the power requirements of the fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
Disconnect main power before servicing and maintenance.
Use safety chain when fixes this fixture. Don’t handle the fixture by taking its head only, but always by taking its base.
Maximum ambient temperature is: 40°C Don’t operate it where the temperature is higher than this.
In the event of serious ope-rating problem, stop using the fixture immediately. Never try to repair the fixture by your-self.
Repairs carried out by unskil-led people can lead to damage or malfunction. Please contact the nearest authorized techni-cal assistance center. Always use the same type spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation and there might be a hazard of electric shock.
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
The housing must be repla-ced if they are visibly damaged.
Do not look directly at the li-ght spot while the fixture is on.

PRODUCT INFORMATION

Light Source: 12R bulb
Power consumption: 310 W
Power supply voltage: 100-240V, 50/60Hz AC PAN range: 540°
TILT range: 270°
Beam angle (min/max): 2°-5°
One color wheel with 14 color and white, half-color function and rotate.
One gobo wheel with 13 gobo and white, shake function and rotate.
Two prism with 0-400° location and rotate.
Two prism with 0-400° location and rotate.
Shut with many kinds of strobe.
Frost filter: 2x frost filter
Operating modes: DMX512, Manual, Auto, Sound-controlled, Master/Slave
DMX channel mode 16
IP Rating: IP20
Housing made: ABS
Cooling: Active
AC IN/OUT: PowerCon 3-Pin XLR DMX Input/Output
Net Weight: 12,2 kg
Net Dimensions: H(51)xW(28)xD(32) cm
Case Weight: 43,2 kg
Case Dimensions: H(61)(wheel 72)xW(66)xD(35) cm

INSTALATION

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.

CONNECTION

The device is equipped with the following interfaces:

DMX (in/out): XLR 3(5)-pin socket
Power (in/out): powerCON socket
The connection is performed using cable with XLR-female -> XLR-Male plugs.

CAUTION! At the last fixture, the DMX signal has to be terminated with a terminator. Solder a 120Ω resistor between signal (-) and si-gnal (+) into a XLR plug and plug it in the DMX output of the last fixture.

FLASH-F7100577-Moving-Head-12R-Light-FIG-2

Diagram of connection of devices by DMX cable.

FLASH-F7100577-Moving-Head-12R-Light-FIG-3

IMPORTANT! The maximum number of devices connected in series via power cable is 4 pcs.

The connection is performed using power cable with powerCON con-nector (included). The device must be operated by qualified personnel.

CAUTION! In the case of cable damage do not attempt to repair. Repla- cement or repair can be made only on the manufacturer or by a person with appropriate permissions
Using lamp, the change rate of power voltage should be within ±10%, if the voltage is too high, it will shorten the light’s life; if it’s not enough, the lamp will be dark. Please restart it after turning off light for 20 mi-nutes until full-cooling. Frequent switching will reduce the life span of lamps and bulbs; intermittent using will improve the life of bulbs and lamps.

Voltage Specyfication.

Input Voltage	Amperage	Frequency	Total Power
100/240 [V] AC	1.42 [A]	50/60 [Hz]	310[W]

Display Operation instruction

MENU: top menu scroll or return to a previous menu option
ENTER: enter to the next level menu or save current setting parameter
UP: menu selection or parameter increments
DOWN: menu selection or parameters decrease

DMX CHART

MODE 16 CH| DMX

VALUE

| FUNCTION
---|---|---
1| 0-255| PAN
2| 0-255| TILT
3| 0-255| PAN fine
4| 0-255| TILT fine
5| 0-255| PAN/TILT speed (fast to slow)
6| 0-127| No effect
| 128-255| Frost 100%
7| 0-5| Shutter Close
| 6-20| Shutter Open
| 21-70| Normal synchronous strobe (slow to fast)
| 71-100| Not synchronous strobe (slow to fast)
| 101-150| Sinewave strobe (slow to fast)
| 151-190| Opening pulse strobe (slow to fast)
| 191-230| Closing pulse strobe (slow to fast)
| 231-255| Shutter Open
8| 0-255| Dimmer 0-100%
9| 0-5| Open (white)
| 6-10| Open > Color 1
| 11-15| Color 1
| 16-20| Color 1 > Color 2
| 21-25| Color 2
| 26-30| Color 2 > Color 3
| 31-35| Color 3
| 36-40| Color 3 > Color 4
| 41-45| Color 4
| 46-50| Color 4 > Color 5
| 51-55| Color 5
| 56-60| Color 5 > Color 6
| 61-65| Color 6
| 66-70| Color 6 > Color 7
| 71-75| Color 7
| 76-80| Color 7 >Color 8
| 81-85| Color 8
| 86-90| Color 8 > Color 9
| 91-95| Color 9
| 96-100| Color 9 > Color 10
| 101-105| Color 10
| 106-110| Color 10 > Color 11
| 111-115| Color 11
| 116-120| Color 11 > Color 12
| 121-125| Color 12
| 126-130| Color 12 > Color 13
MODE 16 CH| DMX

VALUE

| FUNCTION
---|---|---
| 131-135| Color 13
| 136-140| Color 13 > Color 14
| 141-145| Color 14
| 146-150| Color 14 > Open
| 151-190| CW flow (slow to fast)
| 191-205| Color wheel stop
| 206-255| CCW flow (slow to fast)
10| 0-5| Open (white)
| 6-10| Gobo 1
| 11-15| Gobo 2
| 16-20| Gobo 3
| 21-25| Gobo 4
| 26-30| Gobo 5
| 31-35| Gobo 6
| 36-40| Gobo 7
| 41-45| Gobo 8
| 46-50| Gobo 9
| 51-55| Gobo 10
| 56-60| Gobo 11
| 61-65| Gobo 12
| 66-70| Gobo 13
| 71-77| Gobo 1 shake (slow to fast)
| 78-84| Gobo 2 shake (slow to fast)
| 85-91| Gobo 3 shake (slow to fast)
| 92-98| Gobo 4 shake (slow to fast)
| 99-105| Gobo 5 shake (slow to fast)
| 106-112| Gobo 6 shake (slow to fast)
| 113-119| Gobo 7 shake (slow to fast)
| 120-126| Gobo 8 shake (slow to fast)
| 127-133| Gobo 9 shake (slow to fast)
| 134-140| Gobo 10 shake (slow to fast)
| 141-147| Gobo 11 shake (slow to fast)
| 148-154| Gobo 12 shake (slow to fast)
| 155-161| Gobo 13 shake (slow to fast)
| 162-204| CW flow (slow to fast)
| 205-212| Gobo wheel stop
| 213-255| CCW flow (slow to fast)
11| 0-127| Prism 1 off
| 128-255| Prism 1 on
12| 0-127| Prism 2 off
| 128-255| Prism 2 on
13| 0-2| Prism stop rotate
| 3-150| Prism angle 0-400
| 151-200| Prism CW (slow to fast)
MODE 16 CH| DMX

VALUE

| FUNCTION
---|---|---
| 201-205| Prism stop rotate
| 206-255| Prism CCW (slow to fast)
14| 0-127| Rainbow Effect
| 128-255| Color effect 100% (only valid when no frost)
15| 0-255| Focus (from far to near)
16| 0-99| Not valid
| 100-105| Lamp off (at least 3s.)
| 106-199| Not valid
| 200-205| Lamp on (at least 3s.)
| 206-239| Not valid
| 240-255| All motor reset (at least 3s.)

Menu Tree

TOP	LEVEL 1	LEVEL 2	LEVEL 3
DMX ADDRESS	001-512
LAMP	LAMP CONTROL	DO NOTHING AND EXIT/OPEN

LAMP/CLOSE LAMP

中文

Comment

When enter to the “” position displayed on the menu, the fixture will automatically set as master and send data to external. Other fixtures can receive this data and will synchronously running without manually set as slave. When power cycle it will jump to the “” position and running again. And in these position it will not return back to the default display after 30s.
When return factory default only return to the char with under line parameter others will not change.
[SEND PARAMETERS] can send setting parameters with under line via DMX cable and there will be an automatic reset of the other projectors after receiving parameter correctly.

FLASH-BUTRYM Sp.j.
Skarbimierzyce 18 · 72-002 Dołuje · POLAND
WWW.FLASH-BUTRYM.PL