FLASH F7200203 LED Moving Head Bar 10x40W RGBW 2 Sections Zoom 3.5 to 55 Degree 10 Sections Color User Manual

: June 3, 2024
: FLASH

Table of Contents

INTRODUCTION
- SAFETY INFORMATION
WARNING
PRODUCT INFORMATION
INSTALLATION
CONNECTION
DMX CHANNELS
- 60 CH Mode
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

FLASH F7200203 LED Moving Head Bar 10x40W RGBW 2 Sections Zoom 3.5 to 55 Degree 10 Sections Color User Manual

INTRODUCTION

THANK YOU FOR PURCHASING LED MOVING HEAD BAR 10x40W RGBW 2 SECTIONS ZOOM 5°-50° 10 SECTIONS COLOR. FOR SAFETY REASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CAREFULLY READ THE INSTRUCTIONS.

SAFETY INFORMATION

Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the fixture.
Before operating, ensure that the voltage and frequency of power supply match the power requirements of the fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
Disconnect main power before servicing and maintenance.
Use safety chain when fixes this fixture. Don’t handle the fixture by taking its head only, but always by taking its base.
Maximum ambient temperature is: 400CDon’t operate it where the temperature is higher than this.
In the event of serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation and there might be a hazard of electric shock.
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
The housing must be replaced if they are visibly damaged.
Do not look directly at the LED light spot while the fixture is on.

WARNING

WARNING! The LED MOVING HEAD BAR 10x40W RGBW has a powerful pan motor. The torque reaction when the head is panned suddenly can cause the base to move if the fixture is standing unsecured on a surface. Do not apply power to the LED MOVING HEAD BAR 10x40W RGBW unless the baase is securely fastened to a surface or to rigging hardware.
WARNING! Use 2 clamps to rig the fixture. Do not hang the fixture from only one clamp. Lock each clamp with both 1/4-turn fasteners. Fasteners are locked only when turned a full 900 clockwise.
WARNING! When clamping the fixture to a truss or other structure at any other angle than with the yoke hanging vertically downwards, use two clamps of half-coupler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
WARNING! Position or shade the head so that the front lens will not be exposed to sunlight or any other strong light source from any angle – even for a few seconds. See Figure 2. The LED MOVING HEAD BAR 10x40W RGBW lens can focused the sun’s rays, creating a potential fire hazard and causing damage.
IMPORTANT! Do not point strong light output from other fixtures at the LED MOVING HEAD BAR 10x40W RGBW, as intense illumination can damaged the display

Figure 2. Lenses can focused sunlight and strong light, presenting a risk of fire and damage to the fixture. Shield or shade the head if necessary

PRODUCT INFORMATION

Voltage: AC 100V~240V 50/60Hz
Rated power: 500W
LED: 10 x 40W 4in1 RGBW LEDs
Beam angle: 4.5-45°
Average lifetime: ≥50000H
Tilt: 270°( 8bit/16bit precision scanning)
Color: homogeneous RGBW macros color and, wonderful rainbow effec
Fast electric strobe 1 ~ 20 Hz
DMX Channel mode: 24/60CH
Protocol: Auto-run, DMX512, Built-in program, Master-slave, Sound active
Net Weight: 16,6 kg
Dimensions: H(31 )xW(105)xD(12) cm
Dim. (box): H(36)xW(107)xD(18) cm
Weight (case): 17,8 kg

INSTALLATION

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.

CONNECTION

The device is equipped with the following interfaces:

DMX (in/out): XLR 3-pin socket
Power (in/out): power CON socket

Connecting DMX signal

The connection is performed using cable with XLR-female -> XLR-Male plugs.
Connecting DMX signal

CAUTION! At the last fixture, the DMX signal has to be terminated with terminator. Solder a 120Ω resistor between signal (-) and signal (+) into a XLR plug and plug it in the DMX output of the last fixture.

Voltage specification

Input Voltage	Total Power	Frequency
100~240V	500W	50/60Hz

Connecting power supply

The connection is performed using power cable with Power Con connector ( included ) . The device must be operated by qualified personnel.
Make sure that the power grid supply parameters are consistent with device parameters and limitations are not exceeded.

CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only on the manufacturer or by a person with appropriate permissions.

Using lamp, the change rate of power voltage should be within ± 10%, if the voltage is too high, it will shorten the light’s life; if it’s not enough, the lamp will be dark. Please restart it after turning off light for 20 minutes until full-cooling. Frequent switching will reduce the life span of lamps and bulbs; intermittent using will improve the life of bulbs and lamps.

DMX CHANNELS

60 CH Mode

50 Priority 4: Color effect0-9 51 Priority 3:static pattern effect0-9 52 Priority 2: Dynamic pattern effect0-953Effect speed0-25554Effect direction0-12755Background R0-25556Background G0-25557Background B0-25558Background W0-255 59 priority1: macro0-9 60 reset0-239

60 CH	Function	DMX value	Description
1	Y	0-255	0~2700
2	Y fine	0-255	16 bit
3	Y speed	0-255	Fast-slow
4	Zoom 1	0-255	Zoom 1 independent, angle small-big
5	Zoom 2	0-255	Zoom 2 independent, angle small-big
6	Zoom 1-2 aligned	0	Chs 5-6 control
1-255	Zoom 1-2 aligned angle small-big
7	dimmer	0-255	Dark-bright

8

| ****

strobe

24 CH Mode

24 CH	Function	DMX value	Description
1	Y	0-255	0~270 degree
2	Y fine	0-255	16bit
3	Y speed	0-255	Y speed fast-slow
4	Zoom 1	0-255	Zoom 1 independent, angle small-big
5	Zoom 2	0-255	Zoom 2 independent, angle small-big
6	Zoom 1-2 aligned	0	Chs 5-6 controll
1-255	Zoom 1-2 aligned angle small-big
7	dimmer	0-255	Dark-bright

8

| ****

strobe

| 0-9| null
10-154| Speed slow-fast (1HZ~25HZ)
155-204| Random strobe
205-255| Thunder strobe
Led 1-10 dark-bright
Led 1-10 dark-bright
Led 1-10 dark-bright
Led 1-10 dark-bright
null
10-255| 10000K-2500K
null
10-19| Built-in color effect1
20-29| Built-in color effect2
30-39| Built-in color effect3
40-49| Built-in color effect4
50-59| Built-in color effect5
60-69| Built-in color effect6
70-79| Built-in color effect7
80-89| Built-in color effect8
90-99| Built-in color effect9
100-109| Built-in color effect10
110-119| Built-in color effect11
120-129| Built-in color effect12
130-139| Built-in color effect13
140-149| Built-in color effect14
150-159| Built-in color effect15
160-169| Built-in color effect16
170-179| Built-in color effect17
180-189| Built-in color effect18
190-199| Built-in color effect19
200-209| Built-in color effect20
210-224| Built-in color drump change effect
225-239| Built-in color pulsive change effect
240-255| Built-in color gradual change effect
null
10-19| Built-in static pattern effect1
20-29| Built-in static pattern effect2
30-39| Built-in static pattern effect3
40-49| Built-in static pattern effect4
50-59| Built-in static pattern effect5
60-69| Built-in static pattern effect6
70-79| Built-in static pattern effect7
80-89| Built-in static pattern effect8
90-99| Built-in static pattern effect9
100-109| Built-in static pattern effect10
110-119| Built-in static pattern effect11
120-129| Built-in static pattern effect12
130-139| Built-in static pattern effect13
140-149| Built-in static pattern effect14
150-159| Built-in static pattern effect15
160-169| Built-in static pattern effect16
170-179| Built-in static pattern effect17
180-189| Built-in static pattern effect18
190-199| Built-in static pattern effect19
200-209| Built-in static pattern effect20
210-255| Built-in static pattern effect
null
10-29| Built-in dynamic pattern effect1
30-49| Built-in dynamic pattern effect2
50-69| Built-in dynamic pattern effect3
70-89| Built-in dynamic pattern effect4
90-109| Built-in dynamic pattern effect5
110-129| Built-in dynamic pattern effect6
130-149| Built-in dynamic pattern effect7
150-169| Built-in dynamic pattern effect8
170-189| Built-in dynamic pattern effect9
190-209| Built-in dynamic pattern effect10
210-129| Built-in dynamic pattern effect11
230-149| Built-in dynamic pattern effect12
250-255| Built-in dynamic pattern effect13
Dynamic effect fast-slow
Dynamic pattern forward
128-255| Dynamic pattern reverse
0~255 control(59,60)channel background
0~255 control(59,60)channel background
0~255 control(59,60)channel background
0~255 control(59,60)channel background
Null
10-99| Auto 1
100-199| Auto 2
200-255| Sound activated
null
240-250| Reset in 3 seconds
251-255| null

Documents / Resources

| FLASH F7200203 LED Moving Head Bar 10x40W RGBW 2 Sections Zoom 3.5 to 55 Degree 10 Sections Color [pdf] User Manual
F7200203, LED Moving Head Bar 10x40W RGBW 2 Sections Zoom 3.5 to 55 Degree 10 Sections Color, F7200203 LED Moving Head Bar 10x40W RGBW 2 Sections Zoom 3.5 to 55 Degree 10 Sections Color, F7200203 LED Moving Head Bar, LED Moving Head Bar
---|---