FLASH PROFESSIONAL P7100422 / P7100446 300W LED Par 64 Cob User Manual

: June 3, 2024
: FLASH PROFESSIONAL

Table of Contents

FLASH PROFESSIONAL P7100422 / P7100446 300W LED Par 64 Cob
SAFETY INFORMATION
SECURITY PRINCIPLES RELATING TO UV RADIATION
PRODUCT INFORMATION
CONNECTIONS
OPERATION MANUAL
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FLASH PROFESSIONAL P7100422 / P7100446 300W LED Par 64 Cob

FLASH PROFESSIONAL P7100422 P7100446 300W LED Par 64
Cob

INTRODUCTION

Thank you for purchasing LED PAR 64 COB 300W RGBWA+UV Mk2. For safety reasons and to ensure trouble-free operation, carefully read the instructions.

SAFETY INFORMATION

Installation should be done by qualified personnel in order to minimize the risk of accidental electric shock
Disconnect the power supply before installation.
Before connecting the unit to the mains, make sure it is not damaged mechanically. If you notice any signs of damage you should contact your dealer immediately. Do not connect the device to the mains.
Do not use the device in high humidity conditions and at temperatures above 40° C
The device must be installed on stable structures
Always use steel security cable to attach the device to a stable structure
Do not connect power supply to more than 3 devices in series.

SECURITY PRINCIPLES RELATING TO UV RADIATION

A device emitting UV light can be installed and used only by personnel trained in the knowledge of the hazards when using UV light sources, methods to counteract these threats and the rules of safe use of such sources (particularly the high power sources of UV light). The manufacturer is not responsible for damages resulting from improper use of the device.
The device must be installed at a distance from the illuminated people, which ensures a safe staying in a room without compromising the health of the negative effects of UV radiation. The device must be installed in a way as to prevent illumination directly on the skin, face or eyes. The room can be illuminated only by light reflected from the surface (walls, ceilings) – never through direct referral of the reflector in the direction of people in the room.

Threats to health, effects of exposure to UV radiation
An excessive effect of UV radiation on the body often has no immediate symptoms. Symptoms of overexposure, including the various stages of burns or Photokeratitis, usually occur from 4 to 24 hours after the exposure. There is a possibility that the level of UV intensity emitted by the device significantly exceeds the naturally occurring level (especially at a short distance from the light source).

SKIN: UV radiation can cause erythema (sunburn) within the exposed skin. This involves redness and/or ulcerations, which can have a different intensity. In the case of improper use of the device effects of UV radiation on the skin can occur even after a few seconds of exposure. Symptoms may be different depending on the genetic background. People with pale to fair skin are more prone to sunburn. Some medications (eg. Contraception), and some food products (eg. celery root, figs) may increase sensitivity to UV radiation. Chronic exposure to UV radiation causes premature skin aging, wrinkles and skin cancer.
EYES: UV radiation is dangerous for the eyes, not only for looking directly into the light source, but also when eyes are exposed to the UV rays reflected from surfaces (reflectors with high power). Exposure of the eye to UV radiation can cause corneal damage and Photokeratitis (painful inflammation of the eye caused by changes induced by UV radiation to the cornea). One of the symptoms may be “feeling of sand in the eyes” which may persist for several days. In extreme cases, it can cause damage to the lens of the eye that can lead to cataracts.
OTHER THREATS: In addition to significant hazards for the eyes and skin, the impact of UV radiation on substances in the air can lead to the generation of toxic compounds that may be harmful to people in the room.

WARNING! When installing and using the device you should provide appropriate conditions, which prevents the occurrence of risks described above.

Personal protective equipment

EYE PROTECTION: Eye protection must be worn at all case where there is possibility of exposure to UV radiation. Glasses should be consistent with ANSI-Z87. Normal eye protection, prescription glasses or contact lenses offer little or no protection. Glasses providing adequate eye protection are marked Z87.1
PROTECTIVE MASK: In some cases, in addition to safety glasses or goggles, a full face protection should be worn. Masks protect the entire face, especially under the chin, where serious skin burns may occur, even in the short time exposure. Full face protection is recommended in case of long term exposure to UV radiation.
PROTECTIVE CLOTHING: In some cases it is required to wear protective clothing to prevent burns resulting from exposure of the skin to UV rays

PRODUCT INFORMATION

The device is equipped with high-quality, bright COB LED with Red, Green, Blue, White and additional Amber and UV chips. Unique design, high quality and high durability make this device a great tool for both power users and those, who value simplicity and reliability.
The ergonomic double bracket (included) facilitates the use of the device in any condition. In order to expand the range of mounting options, the holder has an additional mounting holes.
The electronics is made of high quality components and offers several features such as:

Features

16-bit dimming resolution
Various dimming curves for smooth dimming in 8-bit mode
Dim delay (light bulb simulation)
Full DMX signal regeneration
Electronic protection against overheating
THEATRE or DISCO cooling volume modes.
Permanent color correction
Native support for optional wireless DMX module

Specification

Power consumption: 300W
Power supply voltage: 100 – 245V
Voltage frequency: 50/60Hz
Diode type: COB 6in1
Number of diodes: 1
Diode power: 300W
Display: Color LCD 1,8”
Color: RGBWA + UV
Beam angle (min): 37°
Beam angle (max): 37°
Dimming: Linear: 0 – 100%
Number of DMX channels:
DMX standard: DMX 512
Control interface: 4 buttons
Operating modes: DMX512, Auto, Sound-controlled, Manual color, Master
Features: 16-bit dimming, DMX Signal regeneration, Electronic protection against overheating
AC IN: powerCON
AC OUT: powerCON
DMX IN: XLR – 3 pin
DMX OUT: XLR – 3 pin
IP Rating: IP20
Housing made: ABS
Cooling: Active
Height [cm]: 27
Width [cm]: 30
Depth [cm]: 13
Weight [kg]: 3,6
Weight with packaging [kg]: 4,4
Set includes: Power cord, Double bracket, Barn Doors

Flash Professional LED PAR 6in1 RGBW+UV Mk2

INSTALLATION
After removing the packaging, check if the device was not damaged during transport. Before connecting to the mains, make sure that the device is securely mounted. The manufacturer is not responsible for damage caused by unstable mounting.

CAUTION! Always use steel security cable to attach the device to a stable structure.
Ensure proper connection to the mains and proper grounding. Make sure that the electrical parameters are consistent with device requirements. All activities, including connecting the device to the mains must be performed by qualified personnel.

CONNECTIONS

The device is equipped with the following interfaces:

DMX (in/out): XLR 3-pin socket
Power (in/out): powerCON socket

Connecting DMX signal
The connection is performed using cable with XLR-female -> XLR-Male plugs.

Voltage specification

Input Voltage	Total Power	Frequency
100~245V	300W	50/60Hz

Connecting power supply
The connection is performed using power cable with PowerCon connector (included).
The device must be operated by qualified personnel. Make sure that the power grid supply parameters are consistent with device parameters and limitations are not exceeded.

CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only on the manufacturer or by a person with appropriate permissions.
Maximum number of devices connected in series: 3

OPERATION MANUAL

Control panel
The control panel is equipped with LCD display and 4 control buttons with the following functions:

ESC – go back from the selected options, go to upper menu, cancel changes
DOWN – choose option, edit parameter
UP – choose option, edit parameter
ENTER edit selected option, confirm changes

Master / slave
To achieve desired effects with Master/slave mode set the first device in DMX chain as Master (MASTER function is [ON] ). Set the following devices to DMX mode -> Classic 8 -> CH 001

DMX channel list

FLASH PROFESSIONAL P7100422 P7100446 300W LED Par 64
Cob-4 FLASH PROFESSIONAL
P7100422 P7100446 300W LED Par 64 Cob-5

Standard 8 [8CH]

11-255: Strobe 1-20Hz

CH 3| Red| 0-255: 0-100%
CH 4| Green| 0-255: 0-100%
CH 5| Blue| 0-255: 0-100%
CH 6| White| 0-255: 0-100%
CH 7| Amber| 0-255: 0-100%
CH 8| UV| 0-255: 0-100%

FLASH PROFESSIONAL P7100422 P7100446 300W LED Par 64
Cob-6 FLASH PROFESSIONAL
P7100422 P7100446 300W LED Par 64 Cob-7

Pro 8 [8CH]

Channel| Function| Effect
CH 1| Red| 0-255: 0-100%
CH 2| Green| 0-255: 0-100%
CH 3| Blue| 0-255: 0-100%
CH 4| White| 0-255: 0-100%
CH 5| Amber| 0-255: 0-100%
CH 6| UV| 0-255: 0-100%
CH 7| Dimmer| 0-255: 0-100%
CH 8| Strobe| 0-10: no function

11-255: strobe 1-20Hz

		Pro 9 [9CH]
Channel	Function	Effect
CH 1	Red	0-255: 0-100%
CH 2	Green	0-255: 0-100%
CH 3	Blue	0-255: 0-100%
---	---	---
CH 4	White	0-255: 0-100%
CH 5	Amber	0-255: 0-100%
CH 6	UV	0-255: 0-100%
CH 7	Dimmer	0-255: 0-100%
CH 8	Dimmer fine	0-255: fine adjustment (16-bit)
CH 9	Strobe	0-10: no Function