FRONT RUNNER KSLG001 Slimsport Roof Rack Kit Installation Guide
- June 17, 2024
- Front Runner
Table of Contents
FRONT RUNNER KSLG001 Slimsport Roof Rack Kit
Product Information
Front Runner Lexus GX 460/Toyota Prado 150 Slimsport Tray
The Front Runner Slimsport Tray is a roof rack system designed specifically
for the Lexus GX 460 and Toyota Prado 150 models. It provides a secure and
versatile platform for carrying additional cargo on top of your vehicle. The
tray is made from high-quality materials to ensure durability and strength. It
is easy to install and can be customized to fit your specific needs.
Specifications
- Model: KSLG001
- Compatibility: Lexus GX 460/Toyota Prado 150
- Mounting System: Front Runner specific to your vehicle
- Rack Tray or Load bar Slats: Included in the kit
Product Usage Instructions
Section 1: Getting Organized
Before starting the installation, make sure you have all the necessary
components and tools. Open all the Front Runner rack kit boxes and gather the
assembly instructions for the various components. A complete kit will contain:
- A Front Runner Mounting system specific to your vehicle
- A Front Runner Rack Tray or Load bar Slats
Tools Needed:
- 13mm and 10mm wrenches
- Sealant
- Anti Seize/Oil
- Torx T30 driver
- Marker
- Cordless Driver
- 5mm insulation tape
Section 2: Assembly
- Secure the Joiner Plate (Item 3) to the Foot Rails (Items 1 & 2) using M6 x 16 Flange Button Head Bolts and M6 Nyloc Nuts (Items 11 & 13).
- Secure the Stiffener Plates (Items 5 & 6) to the Foot Rails (Items 1 & 2) using M6 x 16 Flange Button Head Bolts and M6 Nyloc Nuts (Items 11 & 13).
- Loosely fit the Front Support (Item 4) to the Foot Rail (Item 1) using M6 x 16 Flange Button Head Bolts and M6 Nyloc Nuts (Items 11 & 13). Do this for both LH & RH Foot Rails.
- Place M6 Nut Caps (Item 12) over all Nyloc Nuts.
Fit 10 Slimsport Slats (Item 16) to assembly 2.1 using M6 x 25 Thread Forming Screws (Item 14). Note: Do not fit the front slat. Apply a little Anti Seize/Oil on the screw threads before inserting. These are thread forming screws, so take care when using a cordless driver. Tightening Torque: 8-10Nm / 5.9 ft lb – 7.38 ft lb.
Section 3: Preparation
- Remove both factory rails from the vehicle’s roof.
- Clean the ditch before placing silicone into and around each of the fixing points. Use denatured alcohol to ensure the ditch is clean from any residue where the Support Plate 01 (Item 3) will be resting. Place 2x 10mm Spacers and 1x 6mm Spacer (Items 15 & 17) into each of the mounting positions.
FAQ
-
Q: What vehicles are compatible with the Front Runner Slimsport Tray?
A: The Front Runner Slimsport Tray is compatible with the Lexus GX 460 and Toyota Prado 150 models. -
Q: What tools do I need for the installation?
A: You will need a 13mm and 10mm wrench, sealant, anti-seize/oil, Torx T30 driver, marker, cordless driver, and 5mm insulation tape. -
Q: Can I use the Front Runner Slimsport Tray for carrying heavy loads?
A: The Slimsport Tray is designed to carry additional cargo on top of your vehicle. However, please refer to the weight capacity specifications to ensure you do not exceed the recommended limits.
Don’t be a hero and muscle through this installation without reading these
fitting instructions first! Improper installation of this gear may void
certain aspects of your warranty.
Before you begin, take a moment and open all your Front Runner rack kit boxes
and gather the assembly instructions for the various components.
A complete kit will contain:
- A Front Runner Mounting system specific to your vehicle
- A Front Runner Rack Tray or Load bar Slats
This document will guide you through the assembly of the mounting system and
assist you in fitting the roof rack tray or load bars to your specific
vehicle.
Please refer to the next page for a list of all the components, quantities and
tools required.
IMPORTANT WARNING!
ALL FRONT-RUNNER PRODUCTS MUST BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED
TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT
AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR
ASSEMBLING AND SECURING ALL FRONT-RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING
THE ATTACHMENTS BEFORE USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR
ADJUSTMENT, WEAR AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF
THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT-RUNNER PRODUCT PRIOR
TO INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND
CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HA VE THE PRODUCT
INSTALLED BY A PROFESSIONAL INST ALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the
failure to install the product according to these instructions. Please call us
if you have any questions about the installation of this product.
GET ORGANIZED
IN THE BOX
TOOLS NEEDED
ASSEMBLY
- Secure the Joiner Plate (Item 3) to the Foot Rails (Items 1 & 2) as shown using M6 x 16 Flange Button Head Bolts and M6 Nyloc Nuts (Items 11 & 13).
- Secure the Stiffener Plates (Items 5 & 6) to the Foot Rails (Items 1 & 2) using M6 x 16
- Flange Button Head Bolts and M6 Nyloc Nuts (Items 11 & 13)
- Loosely fit the Front Support (Items 4) to the Foot Rail (Item 1) using M6 x 16 Flange
- Button Head Bolts and M6 Nyloc Nuts (Items 11 & 13)
- Do this to both LH & RH Foot Rails.
- Place M6 Nut Caps (Item 12) over all Nyloc Nuts.
- Fit 10 Slimsport Slats (Item 16) to assembly 2.1 using M6 x 25 Thread Forming Screws (Item 14).
- Note do not fit front slat.
- Apply a little Anti Seize/oil on screw threads before inserting. Note these are thread-forming screws.
- Tightening Torque 8-10Nm / 5.9 ft lb – 7.38 ft lb. Take care when using a cordless driver.
PREPERATION
- Remove both factory rails from the vehicle roof.
- Clean the ditch before placing silicone into and around each of the fixing points.
- Use denatured alcohol and ensure the ditch is clean from any residue where the Support
- Plate 01 (Item 3) will be resting on the ditch.
- Place 2x 10mm Spacers and 1x 6mm Spacer (Items 15 & 17) into each of the mounting positions. See 3.4.
- Remove the backing from the double-sided tape on the bottom of the Support Plate (Item 4) before appliyng the Spacer (Item 17) to the Support Plate.
- Remove the backing from the double-sided tape on the bottom of the Spacer before placing the rack on the vehicle.
- Place a bead of silicone down the length of each M8 x 50 Hex Bolts (Item 8) before inserting.
- Secure the rack using M8 x 50 Hex Bolts and M8 x 25 x 2 Flat Washers (Items 8 & 10).
- Ensure that the Suport Plate is fully seated on the ditch mold before tightening.
- Fully tighten all fasteners.
- Place M6 and M8 Nut Caps (Items 7 & 12) over all Hex Bolts.
FIT AND SECURE
- STANDARD WIND FAIRING ASSEMBLY
- Refer to fitment guide RRAC274
- LIGHT BAR WIND FAIRING ASSEMBLY
- Refer to fitment guide RRAC76
COMPLETION
Congratulations! You did it. Take a step back and admire your work!
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
Now’s the time to visit your favourite Front Runner dealer in person or
online.
IMPORTANT! FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER FOR A RECOMMENDED ROOF RATING. FRONT R UNNER CANNOT BE RESPONSIBLE FOR IMPROPER LO ADING BEYOND THE VEHICLE MANUF ACTURER’S STATED LOAD CAPACITY.
© 2023 FRONT RUNNER VEHICLE OUTFITTERS
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>