FRONT RUNNER FAFR010 Low Profile Foot Rails Instruction Manual
- May 15, 2024
- Front Runner
Table of Contents
Ford Ranger T6.2 (2022-Current)/
VW Amarok (2023-Current) Double Cab
Low Profile Foot Rails
START HERE!
READ ME FIRST
Don’t be a hero and muscle through this installation without reading these
fitting instructions first! Improper installation of this gear may void certain
aspects of your warranty.
Before you begin, take a moment and open all your Front Runner rack kit boxes
and gather the assembly instructions for the various components.
A complete kit will contain:
- A Front Runner Mounting System specific to your vehicle
- A Front Runner Rack Tray or Load Bar Slats
This document will guide you through the assembly of the mounting system and
assist you in fitting the roof rack tray or load bars to your specific vehicle.
Please refer to the next page for a list of all the components, quantities and
tools required.
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY
ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN
AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE
RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR
VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING
THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE, YOU MUST READ AND
UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT
RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF
THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE
NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE
PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the
failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this
product.
CHECK ONLINE FOR LATEST FITMENT GUIDE
WWW.FRONTRUNNEROUTFITTERS.COM
GET ORGANIZED
IN THE BOX
1 | 2X | Foot Rail 1LH + 1RH |
---|---|---|
2 | 4X | M8 x 40 Flange Bolt |
3 | 22 X | |
4 | 18X | M8 x 20 Hex Bolt |
5 | 18X | M8 x 16 x 1.6 Flat Washer |
6 | 22 X | M8 Nyloc Nut |
7 | 2X | Front Spacer |
8 | 2X | Rear Spacer |
9 | 4X | Bottom Spacer |
10 | 4X | M8 x 19 x 2SS Flat Washer |
11 | 2X | Support Bracket |
TOOLS NEEDED
FIT AND SECURE – MODELS WITHOUT FACTORY ROOF RAILS
Drop the vehicle’s roof lining.
Look online for videos to assist.
Remove the Ditch Mold from the vehicles roof. Remove the Stud insert from the
plastic trim and place the Bottom Spacer (Item 9) into the opening and mark
the center of the hole (A).
Drill a 6mm Pilot hole and open it to a 8.5mm Hole.
Refit the Ditch Trim with the Bottom Spacer (Item 9) in place.
Apply a bead of sealant on the
threads of the M8 x 40 Hex Bolts and secure the Foot Rail (Item 1) together
with the Support Bracket (Item 11) and the Front and Rear Spacers to the Roof
using M8 x 40 Hex Head Bolts, M8 x 19 x 2 Flat Washers and M8 Nyloc Nuts
(Items 2, 6 & 10).
Place M8 Nut Caps (Item 6) over all M8 Hex bolt heads.
FIT AND SECURE – MODELS WITH FACTORY ROOF RAILS
Drop the vehicle’s roof lining.
Look online for videos to assist.
Remove the OEM Rails with Ditch Trim from the vehicles roof by unbolting the
nut on the inside of the roof.
Remove the EOM rails from the Ditch Trim.
Place the Ditch Trim back into the
vehicles ditch.
In 3.4 you will use the supplied hardware to secure the Foot Rial onto the
Ditch Trim.
Place the Spacers (Item 7 & 8) over the mounting holes in the Ditch Trim.
Apply a bead of sealant on the threads of the M8 x 40 Hex Bolts and secure the
Foot Rail (Item 1) together with the Support Bracket (Item 11) to the Roof
using M8 x 40 Hex Head Bolts, M8 x 19 x 2 Flat Washers and M8 Nyloc Nuts
(Items 2, 10 & 6).
Place M8 Nut Caps (Item 3) over all M8 Bolt heads
Tightening Torque:
M8 : 15-20Nm / 11.06 ft lb – 14.75 ft lb
FIT AND SECURE
4.1 Refer to RRSTUNI when assembling your Slimline II Tray.
Make sure that the wind deflector is installed before you proceed to the next step.
Fit your roof rack to the Foot
Rails using M8 x 20 Hex Bolts, M8 x 16 x 1.6 Flat
Washers and M8 Nyloc Nuts (Items 4, 5 & 6 ) as shown.
Tightening Torque:
M8 : 15-20Nm / 11.06 ft lb – 14.75 ft lb
Refit the Roof Lining.
4.4 Center the rack and tighten fully. Use M8 Nut Caps (Items 3) to finish off
the nuts.
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
Now’s the time to visit your favorite Front Runner dealer in person or online.
IMPORTANT!
FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY
ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER FOR A
RECOMMENDED ROOF RATING. FRONT RUNNER CANNOT BE RESPONSIBLE FOR IMPROPER
LOADING BEYOND THE VEHICLE MANUFACTURER’S STATED LOAD CAPACITY.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters
BornToRoam
Share your adventures on:
© 2023 FRONT RUNNER VEHICLE OUTFITTERS
Documents / Resources
|
FRONT RUNNER FAFR010 Low Profile Foot
Rails
[pdf] Instruction Manual
FAFR010 Low Profile Foot Rails, FAFR010, Low Profile Foot Rails, Profile Foot
Rails, Foot Rails, Rails
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>