Front Runner KSTF001 Slimsport Roof Rack Instruction Manual

October 30, 2023
Front Runner

Front Runner KSTF001 Slimsport Roof Rack Instruction Manual
Front Runner KSTF001 Slimsport Roof Rack

Don’t be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain
aspects of your warranty. Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components.

A complete kit will contain:

  1. A Front Runner Mounting system specific to your vehicle
  2. A Front Runner Rack Tray or Load bar Slats

This document will guide you through the assembly of the mounting system and assist you in fitting the roof rack tray or load bars to your specific vehicle. Please refer to the next page for a list of all the components, quantities and tools required.

IMPORTANT WARNING!

IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions. Please call us if you have any questions about the installation of this product.

CHECK ONLINE FOR LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM

GET ORGANIZED

IN THE BOX

1 2X Foot Rail Front LH / RH
2 2X Foot Rail Rear LH / RH
3 2X Stiffener Plate 01
4 2X Stiffener Plate 02
5 2X Stiffener Plate 03
6 2X Splice Plate
7 11X Slimsport Slat
8 44X M6 x 25 Thread Forming Screw
9 20 X M6 x 16 Flange Button Head
10 20 X M6 Nyloc Nut
11 22 X M6 Nut Cap
12 8X 10mm Plastic Spacer
13 8X M8 x 19 x 12 Flat Washer
14 8X M8 Spring Washer
15 2X M6 x 12 x 1 Flat Washer
16 2X M6 Spring Washer
17 2X M6 x 30 Hex Bolt
18 8X M8 x 60 Hex Bolt
19 3X Jack Nut Long
20 1X Jack Nut Tool
21 2X M6 x 30 Button Head
22 8X M8 Nut Cap2

TOOLS NEEDED

  • 13mm 10mm

  • Anti Seize / Oil

  • Measurement Tap

  • Cordless Driver

  • Sealant

  • Marker

  • Torx T30

  • 5mm 12mm

  • Insulation Tape

FIGURE 1.1
Part Description

ASSEMBLY
Secure the Splice Plates (Item 6) to the Foot Rails (Items 1 & 2) as shown using M6 x 16 Flange Button Head Bolts and M6 Nyloc Nuts (Items 9 & 10). Secure the Stiffener Plates (Items 3, 4, & 5) to the Foot Rails (Items 1 & 2) using M6 x 16 Flange Button Head Bolts and M6 Nyloc Nuts (Items 9 & 10) Do this to both LH & RH Foot Rails. Place M6 Nut Caps (Item 11) over all Nyloc Nuts.
Assembly Instruction

Fit 10 Slimsport Slats (Item 7) to assembly 2.1 using M6 x 25 Thread Forming Screws (Item 8).

Note do not fit front slat.

Apply a little Anti Seize / oil on screw threads before inserting. Note these are thread forming screws.

Tightening Torque 8-10Nm / 5.9 ft lb – 7.38 ft lb. Take care when using a cordless driver.

PREPERATION

With the factory rails removed and starting at the front edge of the molding, measure and mark the dimensions as shown onto both the LH & RH ditch moldings.
Assembly Instruction

PREPERATION

PERMANENT FITMENT (RECOMMENDED

Place the assembled Rack on the vehicle, lining up the holes in the foot rail with the factory holes in the roof. Mark the hole centres where the ditch moldings were cut out. Remove the Rack.
Assembly Instruction

Before drilling the holes in the roof, take both the 5mm & 12mm drill bits and wrap a band of insulation tape around each bit to act as a stopper to prevent you from drilling to deep as there are airbags located below where you will be drilling. Drill a 5mm pilot hole on both markings. Open holes to 12mm.
Assembly Instruction

Insert the M6 Button Head Bolt (Item 21) into the one side of the Installer Wrench (Item 20), loosly fit a Jack Nut (Item 19) to the Button Head Bolt as shown. Using the Installer Wrench and a M6 x 30 Button Head Bolt, insert the M6 Jack Nuts into the holes drilled. Place the Assembly into the holes drilled in 3.3. Using a battery powered screw driver and a 4mm Allen Key Bit, set the Jack Nut into the hole while holding onto the handle of the Installer Wrench.

Make sure that the Jack Nut has pulled up all the wat to the inside skin of the roof panel.
Assembly Instruction

FIT AND SECURE

Place silicone into and around each of the fixing points. Place Spacers (Item 12) over the mounting holes.
Assembly Instruction

Remove the backing from the double sided tape (4.2a) on the bottom of the Support Plate 01 (Item 3) and push the plate firmly down onto the body of the vehicle. Secure Rack assembly 2.2 using M6 x 12 x 1 Flat Washers, M6 Spring Washers and M6 x 30 Hex Bolts for front foot (Items 14, 15 & 17).

Place a bead of silicone down the length of each M6x20 bolt before inserting. Secure the middle and back feet using M8 x 19 x 2 Flat Washers, M8 Spring Washers and M8 x 60 Hex Bolts (Item 18, 13 & 14).

Fasten the front foot by inserting the fastener (item 17) through the double sided tape and securing into the Jack Nut fitted earlier. Fully tighten all fasteners. Place M6 and M8 Nut Caps over all hex Bolts.
Assembly Instruction

PREPERATION

With the factory rails removed and starting at the front edge of the molding, measure and mark the dimensions as shown onto both the LH & RH ditch moldings.
Assembly Instruction

Use denatured alchohol and ensure the ditch is clean from any residue where the Support Plate 01 (Item 3) will be resting on the ditch.
Assembly Instruction

FIT AND SECURE

Place silicone into and around each of the fixing points. Place Spacers (Item 12) over the mounting holes.
Assembly Instruction

Remove the backing from the double sided tape (4.2a) on the bottom of the Support Plate 01 (Item 3) and push the plate firmly down onto the body of the vehicle. Secure Rack assembly 2.2 using M6 x 12 x 1 Flat Washers, M6 Spring Washers and M6 x 30 Hex Bolts for front foot (Items 14, 15 & 17).

Place a bead of silicone down the length of each M6x20 bolt before inserting. Secure the middle and back feet using M8 x 19 x 2 Flat Washers, M8 Spring Washers and M8 x 60 Hex Bolts (Item 18, 13 & 14). Fully tighten all fasteners. Place M6 and M8 Nut Caps over all hex Bolts.

Assembly Instruction

FIT AND SECURE

STANDARD WIND FAIRING ASSEMBLY

Refer to fitment guide RRAC234
Assembly Instruction

LIGHT BAR WIND FAIRING ASSEMBLY

Refer to fitment guide RRAC195
Assembly Instruction

COMPLETION8.1 Congratulations! You did it. Take a step back and admire your work!

INSTALL OTHER VEHICLE AND RACK ACCESSORIES
Now’s the time to visit your favorite Front Runner dealer in person or online.

IMPORTANT!
FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER FOR A RECOMMENDED ROOF RATING. FRONT RUNNER CANNOT BE RESPONSIBLE FOR IMPROPERLOADING BEYOND THE VEHICLE MANUFACTURER’S STATED LOAD CAPACITY.

Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters

BornToRoamShare your adventures on:![Symbol](https://manuals.plus/wp-

content/uploads/2023/06/Screenshot_28-141.jpg)

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Front Runner User Manuals

Related Manuals