FRONT RUNNER RRAC222 Awning Mount Instruction Manual

October 30, 2023
Front Runner

FRONT RUNNER logo

Quick Release
Awning Mount
RRAC222

FRONT RUNNER RRAC222 Awning Mount -

READ ME !
Thank you for purchasing a Front Runner Quick Release Awning Mount Kit.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received.
Refer to Page 2 for a list of all the components, quantities and tools required.

**** IMPORTANT WARNING!

IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.

GET ORGANIZED

IN THE BOX

1  2 X Awning Mount Bracket
2 2 X Rack Mount Bracket
3 2 X Rack Support Bracket
4 2 X Catch
5  2 X Bobbin – Male
6  2 X Bobbin – Female
7 2 X M8 x 30 Carriage Bolt
8  14 X M8 Nyloc Nut
9  4 X M8 x 25 Button Head Bolt
10  6 X M8 x 16 Hex Head Bolt
11  4 X M6 x 16 Hex Head Bolt
12 4 X M6 x 19 x 1 Flat Washer
13 4 X M8 x 16 x 1.6 Flat Washer
14 4 X M6 Nyloc Nut
15  4 X M6 Nut Cap
16  8 X M8 Nut Cap
17 2 X M8 x 16 Button Head Bolt
18 2 X Awning Wall Mount Bracket
19 4 X Awning Plug Screw 6mm

TOOLS NEEDED

FRONT RUNNER RRAC222 Awning Mount - TOOLS NEEDED

FRONT RUNNER RRAC222 Awning Mount - FIGURE 1.1

FIT AND SECURE

2.1 Determine the orientation of the Awning Mount Bracket (Item 1).
The Bracket can be fitted vertically or horizontally.

FRONT RUNNER RRAC222 Awning Mount - Determine the
orientation

2.2 Assemble the Catch, Male Bobbin & Female Bobbin (Items 4, 5 & 6) to the Awning
Bracket (Item 1) using M8 x 30 Carriage
Bolt and a M8 Nyloc Nut (Items 7 & 8), do not fully tighten.
Fully tighten only the M8 x 16 Button Head
Bolt and M8 Nyloc Nut (Items 8 & 17).

FRONT RUNNER RRAC222 Awning Mount - Assemble the Catch 2.3 Loosely fit the assembly from 2.2 onto the back of your awning. Depending on the make of your awning use either M6 x 16 or M8 x 16 Hex Bolts, Nyloc Nut and Flat Washers. (Items 8, 10, & 13 or 11, 12 & 14) as shown The Brackets will be fully tightened in 2.5.FRONT RUNNER RRAC222 Awning Mount -
Loosely fit the assembly

2.4 Slide the Rack Mount Bracket (item 2) onto the Bobbin Assembly.
Check For excess movement and tighten the nut (A) to reduce / remove any movement.
Remove the Rack Mount Bracket (Item 2), it should be snug but still removed with ease.FRONT RUNNER RRAC222 Awning Mount - Mount
Bracket

2.5 Place the Rack Mount Brackets (Item 2) over the side profile, followed by the Rack  Support (Item 3) and secure using M8 x 25 Button Head Bolts, M8 x 30 Button Head Bolts, M8 x 16 Hex Bolts and M8 Nyloc Nuts (Items 8, 9 & 10) as shown.
Finish off by placing M8 Nut Caps (Item 16) on the Nyloc Nuts.FRONT RUNNER
RRAC222 Awning Mount - Rack Mount Brackets

**** The Rack Mount Brackets (Item 2) need to be in line with a slat as shown in 2.5.

2.6 Measure the pitch of the Rack Mount Brackets. Transfer the measurement over to the Awning Brackets.
Fully tighten the Awning Brackets after you have set them.
Finish off by placing Nut Caps over the Nyloc Nuts. FRONT RUNNER RRAC222
Awning Mount - Measure the pitch

2.7 Position the assembled awning over the Rack Brackets and slot down into position.
Place the hoop of the latch over the hook of the Catch on the Mounting Bracket.
Close the Latch to secure the awning.FRONT RUNNER RRAC222 Awning Mount
-assembled awning

2.8 Use the Wall Mount Brackets (Item 18) to store the awning when not in use.
Chose the desired height you want to store the awning on the wall. Start by placing one of the Wall Mount Brackets against the wall at your desired height. Mark the holes in the
Bracket onto the wall. Note the orientation of the Bracket in 2.7. Using a 6mm concrete drill bit, drill on the marks you have made. Secure the Bracket to the wall using two 6×35 Nail In Anchors (Item 19) as shown.
Measure the pitch of the Awning Brackets. Transfer the measurement over to the Wall Mount Brackets using the mounted Bracket as a start point.
Mark the holes in the second Bracket onto the wall. Using a 6mm concrete drill bit, drill on the marks you have made. Secure the  Bracket to the wall using two 6×35 Nail In Anchors (Item 19) as shown.FRONT RUNNER RRAC222 Awning
Mount - Wall Mount Brackets

FINISH

Congratulations! You did it. Take a step back and admire your work!

INSTALL OTHER VEHICLE AND RACK ACCESSORIES

Now’s the time to visit your favorite Front Runner Dealer in person or online.

FRONT RUNNER logo

Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters

BornToRoam

Share your adventures on:

© 2022 FRONT RUNNER VEHICLE OUTFITTERS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Front Runner User Manuals

Related Manuals