Front Runner F_RRAC244 Toyota Hilux Slimsport Rack Wind Fairing

Product Information

The Front Runner Toyota Hilux Slimsport Rack Wind Fairing is a wind deflector designed to reduce wind noise and drag when using the Slimsport Rack. The fairing comes with all the necessary components for installation, including wind fairing side supports, light bar brackets, M6x16 flange button head screws, M8x16 hex head bolts, M8 nyloc nuts, M8 nut caps, and wind fairing rubber.

Product Usage

1. Before starting the installation process, read the fitting instructions provided and familiarize yourself with the components received.
2. Refer to page 2 of the manual for a list of all the components, quantities, and tools required.
3. Use a Torx cordless driver and a 13mm wrench to install the wind fairing. Slide one M8 x 16 Hex Head Bolt into the T-slot of the front slat. Center the mid support bracket in the middle of the slat and secure it using an M8 Nyloc Nut. Place an M8 Nut Cap over the Nyloc Nut. Fit the Light Bar Bracket 01 LH/RH for the 40 Light Bar using M8x16 Hex Bolt & M8 Nyloc Nut. Fit the light bar and center it on the slat before fully tightening the brackets. Place an M8 Nut Cap over all Hex Bolts.
4. Secure assembly 2.2 to the front two top holes on the foot rails using the fasteners supplied with KSTH002. Tighten Torque to 8-10Nm / 5.9 ft lb – 7.38 ft lb.
5. To secure the Wind Fairing Side Supports LH/RH to the foot rails top holes, use the Torx cordless driver and M6x16 Flange Button Head screws.
6. Fit the Wind Fairing Rubber to the Light Bar Wind Fairing. Use the notched section as a guide and trim if needed.
7. Secure the Light Bar Wind Fairing assembly to the rack assembly using M8x16 Flange Button Heads and fully tighten.
8. Once installation is complete, take a step back and admire your work!
9. You can also install other vehicle and rack accessories from Front Runner by visiting your favorite Front Runner Dealer in person or online.

READ ME !

Thank you for purchasing a Front Runner Toyota Hilux Slimsport Rack Wind Fairing. Before you start, take a moment to familiarize yourself with the Fitting Instructions and the components received. Refer to Page 2 for a list of all the components, quantities and tools required.

IMPORTANT WARNING!

IT IS CRITICAL THAT ALL FRONT-RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT-RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT- RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions. Please call us if you have any questions about the installation of this product.

GET ORGANIZED

TOOLS NEEDED

FIT AND SECURE

1. Slide one M8 x 16 Hex Head Bolt (Item 7) into the T-slot of the front slat. Center the mid support bracket in the middle of the slat and secure using M8 Nyloc Nut (Item 8). Fully tighten.  Place a M8 Nut Cap over the Nyloc Nut.
2. Fit the Light Bar Bracket 01 LH / RH (Item 4) for the 40″ Light Bar, using M8x16 Hex Bolt & M8 Nyloc Nut (Items 7 & 8). Fit the light bar and center it on the slat before fully tightening the brackets. Place M8 Nut Caps (Item 9) over all Hex Bolts.
3. Secure assembly 2.2 to the front two top holes on the foot rails using the fasteners supplied with KSTH002.
   • Tightening Torque 8-10Nm / 5.9 ft lb – 7.38 ft lb.
4. Secure the Wind Fairing Side Supports LH / RH (Item 2) to the foot rails top holes as shown using M6x16 Flange Button Head (Item 6).
5. Fit the Wind Fairing Rubber (Item 13) to the Light Bar Wind Fairing (Item 1). Using the notched section as a guide, trim if needed. Secure the Light Bar Wind Fairing assembly to the rack assembly, using M8x16 Flange Button Heads (Item 6) and fully tighten.

FINISH

Congratulations! You did it. Take a step back and admire your work!

INSTALL OTHER VEHICLE AND RACK ACCESSORIES

Now’s the time to visit your favorite Front Runner Dealer in person or online. Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters

BornToRoam Share your adventures on:

• 2022 FRONT RUNNER VEHICLE OUTFITTERS
• RRAC244_REV _A00

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>