ROUGH COUNTRY SRB100 HD2 2 HD Receiver Hitch Step Instruction Manual
- June 16, 2024
- Rough Country
Table of Contents
ROUGH COUNTRY SRB100 HD2 2 HD Receiver Hitch Step
- Thank you for choosing Rough Country for all your vehicle needs.
- Please read the instructions before beginning installation.
- Check the kit hardware against the kit contents shown below.
- Be sure you have all the needed parts and know where they go.
- If a question exists, please call us at @1-800-222-7023.
- We will be happy to answer any questions concerning this product.
- Check all fasteners for proper torque. Check to ensure adequate clearance between all components. Periodically check all hardware for tightness.
Components Included
- 1 – Step Rail
- 1-2” Receiver Tube
- 1-Clamp Bracket
- 1-Hitch Pin w/ Clip
Hardware Included
- 2-Double Bolt Plates
- 1-10mm U-Bolt
- 2-10mm Flat Washers
- 2-10mm Nylon Lock Nuts
- 4-6mm Flat Washers
- 4-6mm Lock Washers
- 4-6mm Hex nuts
Tools Required
- 10mm Wrench / Socket
- 17mm Wrench / Socket
Torque Specs: Size Grade 5 Grade 8 Size Class 8.8 Class 10.9
- 5/16” 15 ft/lbs 20ft/lbs 6MM 5ft/lbs 9ft/lbs
- 3/8” 30 ft/lbs 35ft/lbs 8MM 18ft/lbs 23ft/lbs
- 7/16” 45 ft/lbs 60ft/lbs 10MM 32ft/lbs 45ft/lbs
- 1/2” 65 ft/lbs 90ft/lbs 12MM 55ft/lbs 75ft/lbs
- 9/16” 95 ft/lbs 130ft/lbs 14MM 85ft/lbs 120ft/lbs
- 5/8” 135ft/lbs 175ft/lbs 16MM 130ft/lbs 165ft/lbs
- 3/4” 185ft/lbs 280ft/lbs 18MM 170ft/lbs 240ft/lbs
INSTALLATION INSTRUCTIONS
- Locate the tow hitch below the rear bumper. See Photo 1.
- Assemble the step hitch bracket with the L-shaped bracket and supply U-bolt / hardware. See Photo 2.
- Insert the hitch tube step bracket in the receiver and align the holes in the tube with the mounting holes on the Bracket.
- NOTE: There are 3 mounting holes available for pin adjustment. Insert the hitch pin through the receiver tube and step tube bracket hole. Secure in place with the supplied hitch pin. See Photo 3.
- Place the L Bracket under the drawbar and up against the end of the receiver hitch. Insert the supplied 10mm U-bolt over the tube and down through the L Bracket. Secure using the supplied 10mm Flat Washers x 2 and 10mm Nylon lock nuts x 2 to secure the Bracket to the hitch.
- NOTE: The L Bracket is used to help prevent rattling. Do not tighten the hardware at this time. See Photo 3. Assembled base is shown in Photo 4.
- Insert the supplied supplied 6mm bolt plates x 2 into the channels at the bottom of the Hitch Step. Raise the Step and slide the Bolt Plates down through the slots in the base assembly. See Photo 5.
- Secure the step to the base assembly with the supplied 6mm Flat Washers x 4, 6mm Lock Washers x 4, and 6mm hex Nuts x 4. Do not fully tighten the hardware at this time. Level and adjust the Hitch Step to the Draw Bar as necessary and fully tighten all hardware. See Photo 6.
By purchasing any item sold by Rough Country, LLC, the buyer expressly warrants that he/she complies with all applicable, State, and Local laws and regulations regarding the purchase, ownership, and use of the item. It shall be the buyer’s responsibility to comply with all Federal, State, and Local laws governing the sales of any items listed, illustrated, or sold. The buyer expressly agrees to indemnify and hold harmless Rough Country, LLC for all claims resulting directly or indirectly from the purchase, ownership, or use of the items.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>