OSD AUDIO RS850 Rock Speaker Owner’s Manual
- June 16, 2024
- OSD AUDIO
Table of Contents
OSD AUDIO RS850 Rock Speaker
Specifications
- Compatible with any audio amplifier or stereo receiver
- Sealed speaker wire pigtail for easy connection
- Red lead indicates positive signal (+), black lead indicates negative signal (-)
- Power handling: Refer to the owner’s manual
Product Usage Instructions
- Step 1: Select your location
- Avoid placing the speakers in low spots that would make the speakers vulnerable to water accumulation. Refer to Diagram 1 for speaker placement.
- Step 2: Trenching and Cable Burying
- Use a trench spade/shovel to dig trenches for burying the direct burial cables. Place the cables in the trenches and bury them. Ensure the cables are properly protected.
- Step 3: Making the connection
- Connect the rock speakers to your audio amplifier or stereo receiver using the sealed speaker wire pigtail from the back of the speaker enclosure. The red lead indicates a positive signal (+), and the black lead indicates a negative signal (-). Connecting the leads incorrectly will result in a weaker bass response. Refer to Diagram 2 for connection details.
- Step 4: Power connection
- Ensure that the power is off before connecting the speakers. Locate the connection terminals on the back of your receiver or amplifier. Connect the audio out from your receiver or amplifier to the speakers. Please refer to your owner’s manual for specific instructions.
- Step 5: Speaker cable connection
- Connect the speaker cable to the speaker cable terminals, matching the proper polarity with your amplifier. Connect + to + (red) and – to – (black). Make sure to connect the right channel to the right speaker and the left channel to the left speaker. Refer to Diagram 5 for reference.
Tools needed for installation
- Trench Spade/Shovel
- Wire Cutter
- Measuring Tape
- Outdoor Volume Control (Optional)
- Direct Burial Cables
- Silicon Cable Connectors (Optional)
Quick installation guide
- Where is the best place to install the speakers?
- Where will the speakers sound the best?
- Try to separate the speakers 15 – 20 feet apart.
- Place the speakers in the location where they will camouflage the best with your surrounding
Speaker wire
To determine the length and the gauge of the speaker wire, you will need to
measure the distance between your receiver/amplifier and the speakers.
- Measure the distance between the receiver/amplifier and the speakers.
- Always buy more than you think you will need.
- Equal wire lengths should always be used to maintain an equal balance in sound volume.
- Sound quality is lost when using a thin wire gauge over a long distance.
- 18 AWG minimum – for distances up to ………………………. . 10 ft
- 16-2AWG – from ……………………………………………. 10 to 50 ft
- 14-4AWG – from …………………………………………… 50 to 100ft
- 12-2AWG – from …………………………………………… 50 to 100ft
Step 1: Select your location
- Designate the general area where the rock speakers would be most ideal. The speakers should face the general listening area and spaced about 15 – 20 feet apart for good stereo sound. (See
- Diagram 1) Furthermore, the realistic rock shape and finish would blend particularly well in your landscape if it is placed near a rock wall, water fountain, open plantation or swimming pool.
Avoid placing the speakers in low spots that would make the speakers vulnerable to water accumulation.
Step 2: Trenching and Cable Burying
Measure the distance from the designated speaker location to your stereo
receiver. Try to minimize your distance without compromising on your overall
appeal and safety concerns. Once the route is determined, use your spade or
trench to dig the route with width between 8” and -12” once the trench route
is completed, lay the cable in the route. If using the PVC pipe, cut the pipe
to length, and ensure all electrical connections are watertight with silicone
burial connectors. Once the cable layout is done, refill the trench. (See
Diagram 2)
Diagram 1
Step 3 Making the connection
Rock speakers are easily connected to any audio amplifier or stereo receiver using the sealed speaker wire pigtail from the back of the speaker enclosure. Please note, that the red lead indicates a positive signal (+) and the black indicates a negative signal (-). Connecting the positive and negative leads incorrectly will cause it to be out of phase and will result in a weaker bass response.
Remove 2”- 3” of the outer layer of the speaker wire coming out from the source amplifier. Carefully strip ½” of the insulation covering the speaker conductors within the outer layer. Twist the bare speaker wire leads together and seal with burial connector. Do not use Electrical tape as a means of weatherproofing the wire connection. (See Diagram 3)
Step 5
When connecting any speakers to the amplifier or receiver, always make sure
the power is off. Locate the connection terminals on the back of your receiver
or amplifier. Always make sure to connect audio out from the back of your
receiver or amplifier to the speakers.
Not all receivers/amplifiers can safely operate 2 pairs of speakers at the
same time. The amplifier or receiver’s output wattage must be comparable to
the speaker’s power handling. Please refer to your owner’s manual for
reference.
Connect the speaker cable to the speaker cable terminals, matching the proper
polarity with your amplifier, + to + (red) and – to – (black). Make sure to
connect the right channel to the right speaker and the left channel to the
left speaker. Either channel may be attached to either terminal set, however,
be sure that polarity ( + and – ) is correct on each channel or the
performance of the speaker will be seriously affected as one channel will
cancel out the other.
Diagram 5
Warranty & Repair
All OSD Audio speaker products have 1-year Limited Warranty against defects in materials and workmanship. Proof of purchase must accompany all claims. During the warranty period, OSD will replace any defective part and correct any defect in workmanship without charge for either parts or labor.
- OSD Audio may replace returned speakers with a product of equal value and performance. In such cases, some modifications to the mounting may be necessary and are not OSD’s responsibility.
- For this warranty to apply, the unit must be installed and used according to its written instructions. If necessary, repairs must be performed by OSD. The unit must be returned to OSD at the owner’s expense and with prior written permission. Accidental damage and shipping damage are not considered defects, nor is damage resulting from abuse or servicing performed by an agency or person not specifically authorized in writing by OSD.
- OSD Audio sells products only through authorized dealers and distributors to ensure that customers obtain proper support and service. Any OSD product purchased from an unauthorized dealer or other source, including retailers, mail-over dealers, and online sellers will not be honored or serviced under the existing OSD warranty policy. Any sale of a product by an unauthorized source or other manner not authorized by OSD shall void the warranty on the applicable product.
- Damage to or destruction of components due to the application of excessive power voids the warranty on those parts. In these cases, repairs will be made based on the retail value of the parts and labor. To return for repairs, you must email customer service at RMA@osdaudio.com for a Returned Merchandise Authorization (RMA) number# then the unit must be shipped to OSD at the owner’s expense, along with a note explaining the nature of service required. Be sure to pack the speaker(s) in a corrugated container with at least 3 inches of resilient material to protect the unit from damage in transit.
- This Warranty Does Not Cover:
- Damage caused by abuse, accident, misuse, negligence, or improper operation (installation) • Any products that have been altered or modified Any product whose identifying the number of decals, serial #, etc. has been altered, defaced or removed • Normal wear and maintenance
Specifications
FAQ
- Q: What tools are needed for installation?
- A: The following tools are needed for installation: trench spade/shovel, wire cutter, measuring tape, outdoor volume control (optional), and silicon cable connectors (optional).
- Q: Where is the best place to install the speakers?
- A: The speakers should be placed in a location where they will camouflage your surroundings and provide the best sound. Refer to Diagram 1 for speaker placement.
- Q: How do I determine the length and gauge of the speaker wire?
- A: Measure the distance between your receiver/amplifier and the speakers. Always buy more wire than you think you will need. Use equal wire lengths to maintain an equal balance in sound volume. Refer to the provided table for recommended wire gauges based on distance.
- Q: Can I connect multiple pairs of speakers to my amplifier/receiver?
- A: Not all receivers/amplifiers can safely operate 2 pairs of speakers at the same time. It is important to ensure that the amplifier or receiver’s output wattage is comparable to the speaker’s power handling. Please refer to your owner’s manual for reference.
- Q: What should I do if I need a warranty or repair service?
- A: For warranty and repair service, please refer to the warranty and repair information provided in the owner’s manual or contact the manufacturer directly.
OSD Audio
- 775 columbia st
- Brea
- CA
- 92821
- www.osdaudio.com
- Tel 888-779-4968
- Fax 714-256-8300
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>