OSD AUDIO OVC100 100W Outdoor Volume Control Instruction Manual
- June 4, 2024
- OSD AUDIO
Table of Contents
OSD AUDIO OVC100 100W Outdoor Volume Control
Installation Instructions
Step 1: Determine and set impedance with match switch
- Count the total number of 8-ohm and 4-ohm speakers you are connecting to.
- Determine if the amplifier can support an 8-ohm or 4-ohm speaker load. You should be able to find the information in your amplifier or receiver owner’s manual.
- Determine the correct impedance match switch setting using the chart below (See Fig.2)
- Set the impedance match jumper on all the volume controls in the system to the same position (1/2X,4X,or8X). (See Fig.1.)
Figure 1 Impedance Setting
Figure 2 Impedance Chart
OSD Audio does not recommend installing more than 8 volume controls in parallel. OSD audio also does not recommend installing more than two 8 Ohm speakers per channel on each volume control without additional impedance protection.
Setting the impedance match switch higher than 1 X yield less power per pair of speakers. For example an amplifier rated at 80 Watts per channel RMS into 8 ohms is to be used for 8 pairs of speakers. In order to accommodate 8 pair of 8 ohms speakers, an 8 impedance match setting must be used, therefore, this will limit to power to 10 watts for each speaker pair, or 1 /8th of the amplifier’s power. (See Fig. 2).
Step 2: Mounting the enclosure
- If a conduit is to be used, run the necessary wiring up through the conduit and into the opening at the base of the enclosure.
- Mount the enclosure onto the PVC conduit using the applicable adhesive material
- Use the 4 holes in the back sides of the unit to secure the enclosure to a stationary object or wall. (See Fig. 3.)
Step 3: Wiring
Strip ¼”to 1/s” of the insulation from your connection cables. Twist your input wires with the OVC 300 input wires. Apply the same procedure for the output wires. Make sure all the cables are consistent in polarity. (See Fig.4).
Once connected, run the output cables from the Amplifier to the Volume Control’s input wires. Followed by running the cables from the Volume Control’s output to the speakers input terminals. (See Fig. 5).
Wiring Diagram
Warranty & Repair
All OSD Audio electronic products have (1) year Limited Warranty against defects in materials and workmanship. Proof of purchase must accompany aJI claims. During the warranty period, OSD will replace any defective part-;iQd correct any def< in workmanship without charge for either parts or labor.
OSD Audio may replace returned speakers with a product of equal value and
performance. In such cases, some modifications to the mounting are necessary
and are not OSD’s responsibility.
For this warranty to apply, the unit must be installed and used according to
its written instructions. If necessary, repairs must be performed by O5D. The
unit must be returned to OSD at the owner’s expense and with prior written
permission. Accidental damage and shipping damage are not considered defects,
nor is damage resulting from abuse or from servicing performed by an agency or
person not specifically authorized in writing by OSD.
OSD Audio sells products only through authorized dealers and distributors to ensure that customers obtain proper support and service. Any OSD product purchased from an unauthorized dealer or another source, including retailers, mail-over dealers and online sellers will not be honored or serviced under existing OSD warranty policy. Any sale of product by an unauthorized source or other manner not authorized by OSD shall void the warranty on the applicable product.
Damage to or destruction of components due to the application of excessive power voids the warranty on those parts. In these cases, repairs will be made on the basis of the retail value of the parts and labor. To return for repairs, you must email customer service at RMA@osdaudio.com for a Returned Merchandise Authorization (RMA) number# then the unit must be shipped to OSD at the owner’s expense, along with a note explaining the nature of service required. Be sure to pack the speaker(s) in a corrugated container with at least 3 inches of resilient material to protect the unit from damage in transit.
This Warranty Does Not Cover:
Damage caused by abuse, accident, misuse, negligence, or improper operation
(installation) • Any products that have been altered or modified • Any product
whose identifying number of decal, seljal #, etc. has been altered, defaced or
removed • Normal wear and maintenance.
Technical Specifications
- Audio Power Handling:
- OVC 50: 50 Watts Maximum
- OVC 100: 100 Watts Maximum
- OVC 300: 300 Watts Maximum
- Frequency Response: 20Hz – 20kHz
- Total Attenuation: 42dB Maximum
- Wiring requirement: 14 – 16 gauge wire, input and output (separate):
- two separate 2 – conductor speaker wires, or one 4 – conductor speaker wire.
- Mounting: May be mounted on wall or via PVC conduit
- Impedance Matching: 1 /2X, 4X & BX
- Unit Dimensions: 3″W x 51/e”H x 4″D
- Control: Up to 2 speakers
- Warranty: 5 Year
Call 562-697-2600 or visit www.osdaudio.com. for information.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>