OSD AUDIO ISS4 Protected Loudspeaker Switcher Owner’s Manual
- June 4, 2024
- OSD AUDIO
Table of Contents
ISS4 Protected Loudspeaker Switcher
Owner’s Manual
ISS4 ISS6 ISS8
Protected Loudspeaker Switcher
Owner’s Manual
ISS4 Protected Loudspeaker Switcher
Thank you for giving OSD AUDIO the chance to earn your business! We are
confident you will find that OSD offers an outstanding combination of
performance and value in everything we make. To ensure you get the most out of
your ISS468, please take a moment to read this manual before you get started
WARNING
Please read the Manual carefully before operating this unit.
Controls
-
Loudspeaker selectors 1 through 8 – press the button in to listen to the desired loudspeakers.
-
Single Pair Direct Switch – impedance protection switches the amplifier/receiver.
-
Connection from amplifier – from the L (left) and (right) loudspeaker output of your receiver or amplifier ( 100 watts MAX )
-
Loudspeaker Connections – connections to be made from the QLS8.1 to the desired loudspeakers, with the corresponding selector on the front panel.
**Typical Hook-Up
**
Overview of the typical system
The diagram below shows an overview of a typical system using 8 loudspeaker
pairs
Installation Tips
- 16 or 18-gauge stranded loudspeaker wire is recommended. 14 gauge is recommended for runs longer than 50 feet.
- You can mix any combination of 4, 6, 8, and 16-ohm loudspeakers
- Wire according to local laws. Specific ” CL ” fire ratings may be required according to your local building codes. Your dealer may know more about obtaining such wire.
- Avoid running close to AC power wiring for safety and to avoid the possibility of picking up any noise.
Installation
ISS4, ISS6, ISSB Speaker Selectors
Thank you for giving OSD AUDIO the chance to win your business! We are confident you will find that OSD offers an outstanding combination of performance and value in everything we make. To ensure you get the most out of your new amplifier, please take a moment to read this manual before you get started .
Features
The OSD ISS4, ISS6 and ISSB are low-profile speaker selector boxes that allow
you to distribute a stereo highlevel (amplified) signal into multiple zones.
All models include a manually activated impedance protection circuit that can
be turned ON to prevent the impedance presented to your receiver from dropping
below an unsafe level of 5 Ohm, regardless of the number and impedance ratings
of your speakers. The protecting switch can also be turned off when used as
part of a planned system of impedance matching volume controls, allowing you
to get most out of your amplifier. If you are unsure, consult a professional
contractor.
Connecting your OSD Speaker Selector
The terminals on the rear of the speaker selector will accommodate up to 14
gauge cable which will suffice for even long connections (greater than 100
Feet of wire) . For shorter distances, 16- or 18-gauge wire will suffice. For
behind-the-wall installations, we recommend using UL Class 3 approved cable
(marked “CL3”) for compliance with local building codes. When connecting a
speaker and amplifier, it is important to retain the correct polarity. To do
this, be sure that the wire is attached to the+. red. or positive terminal on
the speaker connects to the+ . red, or positive terminal on the rear of the
selector box. Similarly, the -, black, or negative terminal on the speaker
must connect to the respective -, black, or negative terminal on the selector
box. Polarity should also be maintained when connecting your amplifier’s
output to the amplifier on the selector box.
Connecting Speaker Cables
- Route the speaker cables from the amplifier and from each speaker zone to the speaker selector.
- Strip 3/8″ insulation from the end of the cable and twist the exposed end to avoid fraying.
- Press on a “push-pin” terminal to reveal an eye into which the twisted cable is inserted; release the terminal to lock
Specifications
Listening Zones Protection Circuit High Power Resistors Power Handling with Protection Circuit ON Power Handling with Protection Circuit OFF Dimensions: H x W x D
| ISS4| ISS6| ISS8 J
---|---|---|---
Listening Zones| 4| 6| 8
Protection Circuit High Power Resistors| 2 x 10 ohm/15 watts per channel| 2 x
10 ohm/15 watts per channel| 3 x 10 ohm/15 watts per channel
Power Handling with Protection Circuit ON| 70 watts/channel| 70 watts/channel|
100 watts/channel
Power Handling with Protection Circuit OFF| 140 watts/channel| 140
watts/channel| 200 watts/channel
Dimensions: H x W x D| 218 x 112 x 49 mm 8.5′ x 4.4″ x 1.93′| 433 x 112 x 49
mm 1 7″ x 4.4″ x 1.93″| 433 x 112 x 49 mm 17′ x 4.4″ x 1.93″
Never place a speaker selector where it is exposed to excessive moisture or heat. Leave at least 1″ of space above the unit for heat dissipation.
775 Columbia St
Brea· CA· 92821
www.osdaudio.com
Tel 562-697-2600
Fax 562-697-2668
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>