ORION 23REDB Basic Led Display Monitor User Guide

: June 16, 2024
: Orion

Table of Contents

ORION 23REDB Basic Led Display Monitor
Product Usage Instructions
FAQ
How to fix
INSTALLATION
Part List
Main Functional Button
Connection
FEATURES AND Specification
APPENDIX
FCC STATEMENT
TROUBLESHOOTING
Warranty
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ORION 23REDB Basic Led Display Monitor

Product Usage Instructions

Warning Statements

Follow these safety instructions to use the monitor properly and prevent damage:

WARNING: Failure to follow this instruction may cause serious damage to the user.
CAUTION: Failure to follow this instruction may cause slight damage to the user or damage to the monitor.

Additional Warning Statements

Do not install this monitor outside or near water. It may cause damage to the product, electric shock, and fire.

For cleaning, do not use liquid cleaners. Never touch the power plug with wet hands.

When there is lightning and thunder, unplug the monitor from the wall outlet and avoid touching it.
Unplug this product from the wall outlet when it does not operate for a long time.
If there is smoking and noise from the monitor, unplug the product from the wall outlet and contact a service centre.

How to Fix

Do not open this product as it contains high voltage inside.
Opening it may create an electric shock.
If the user disassembles and removes the back cover, it does not ensure proper functioning.
To address damages and perform service or exchange the monitor, contact a service centre.

Cautions

Follow these cautions when using the monitor:
Install this monitor some distance from the wall and ensure proper ventilation.
Place this product on a stable surface to prevent falling and causing serious damage to the monitor and people.
Ensure that the openings are not blocked by curtains, rugs, or other similar surfaces.
When carrying this monitor, be careful not to damage the panel and avoid dropping it, as it may cause trouble.
Before carrying the monitor, turn it off and unplug the signal cables and power cord from the wall outlet.
Take the power plug out from the wall outlet without pulling the cable, as it may snap the inner wires and cause overheating and fire.
Install this monitor approximately 50cm away from the eyes and at an angle of 0~15 degrees below eye level. Installation that is too close may cause weak eyesight.
Do not press the LCD panel with your hands or any sharp material forcefully.

For cleaning, unplug the monitor from the wall outlet. Use a soft cloth; do not use liquid cloth or chemical liquids, as they may cause fading and breakage.

FAQ

Q: Can I use liquid cleaners to clean the monitor?
A: No, liquid cleaners should not be used. Use a soft cloth instead.

Warning Statements

Follow this safety instruction to use the monitor properly and prevent damage.

This safety instruction has “ Warning” and “ Caution” as below.
WARNING: If the user does not follow this instruction, it may cause serious damage to the user.
CAUTION: If the user does not follow this instruction, it may cause slight damage to the user or cause some damage to the monitor.

Keep this user’s guidebook for later use

Never remove the back over and touch the inside of the monitor. If you need a service, please contact the service centre.
Keep away the monitor from direct sunlight and a heating appliance.
Never push objects of any kind into this product as they may result in a risk of fire or electric shock.
Connect the power code to the wall outlet tightly. If the power code or plug is defective and the wall outlet is not tight, please do not use them.
Do not install this monitor on the outside and near water. It may cause damage to the product, electric shock and fire.
For cleaning do not use liquid cleaners. Never touch the power plug with wetlands.
When lightning and thunder, unplug the monitor from the wall outlet and never touch it.
Unplug this product from the wall outlet, when It does not operate for a long time.
When smoking and noising from the monitor, unplug the product from the wall outlet and contact a service centre.

How to fix

Do not open this product as it contains high voltage inside.
It may create an electric shock.
If the user disassembles and removes the back cover, it does not make sure
To make up for the damages and do service and exchange the monitor.

Cautions

Install this monitor some distance From the wall and do not install it unless Proper ventilation is provided.
Place this product in a stable place. If not, it may fall, causing serious Damage to the monitor and people.
The openings must not be blocked by a curtain, rug or another similar surface.
When carrying this monitor, be careful not to damage the panel and drop it It may cause some trouble.
Before carrying the monitor, turn it off and Unplug the signal cables and the power code From the wall outlet.
Take the power plug out from the wall outlet. Do not pull the cable. It may snap the inner wires and cause overheating and fire.
Install this monitor about 50cm away from the eyes and at an angle of 0~15 degrees below the eyes. Too close installation may cause weak sight.
Do not press the LCD panel with hands or the sharpened material hard.
For cleaning, unplug the monitor from the Wall outlet. Do not use the liquid cloth. Use a soft cloth.
Do not use the chemical liquid for cleaning. It may cause fading and breakage.

INSTALLATION

Unpacking
Remove the package cover and place the product on a flat and secure surface or in the installation location. This equipment should be unpacked and handled with care. If an item appears to have been damaged in shipment, notify the shipper immediately. Check whether all the following devices and accessories are included with the main system. If any items are missing, notify your Sales or Customer Service Representative.

Part List

The following table lists the parts included:

Main Functional Button

RECALL
Select to reset all settings to the factory default values.
ASPECT
Turn on the monitor and set the monitor ratio to 4:3, wide..
AUTO
Adjust screen automatically.
+
Move to the right (increase) on OSD.
‐
Move to the left (decrease) on OSD.
MENU
Activates and exits the OSD
/ POWER
Turns the power ON or OFF. There will be a few seconds delay before the display appears. The power LED(next to the power switch) lights with green when the power is turned ON. The power is turned off by pressing the power switch again and the power LED goes Red.

Connection

VGB In (15 Pin D-SUB)
Connect the VGA signal cable.
DVI-D In
Connect the DVI cable.
Audio In
Connect the Audio cable.

OSD (On Screen Display) SETTING

D-SUB Mode

DVI Mode

Miscellaneous Menu

Colour control screen
OSD control screen (VGA)
OSD control screen (DVI)

OSD Function

FEATURES AND Specification

FEATURES

Specification

VIDEO

Screen Size| 18.5”| 21.5”| 23”
Pixel Type| Active Matrix TFT| Active Matrix TFT| Active Matrix TFT
Panel Resolution| 1366 x 768 @60Hz| 1920 x 1080 @60Hz| 1920 x 1080 @60Hz
Pixel Pitch| 0.3mm x 0.3mm| 0.248 x 0.248 mm| 0.265 x 0.265 mm
Brightness| 250 cd/㎡| 250cd/m²| 250cd/m²
Contrast Ratio| 1000: 1| 1000:1| 1000:1
Aspect Ratio| 16: 9| 16: 9| 16: 9
Viewing Angle (H/V)| 170°/160°| 170°/160°| 170°/160°
Display Color| 16.7 Million| 16.7 Million| 16.7 Million
Response Time| < 5ms| < 5ms| < 5ms
Video System| NTSC / PAL / SECAM| NTSC / PAL / SECAM| NTSC / PAL / SECAM
Frequency (H)| 60 ~ 81KHz| 60 ~ 81KHz| 60 ~ 81KHz
Frequency (V)| 55 ~ 75Hz| 55 ~ 75Hz| 55 ~ 75Hz
Panel Lamp Life| 30,000hours| 30,000hours| 30,000hours
MECHANICAL
Outline Dimension

W x D x H

APPENDIX

D-SUB Connector PIN Assignment

PIN NO.	PIN Name	PIN NO.	PIN Name
1	RED VIDEO	9	NC
2	GREEN VIDEO	10	SIGNAL CABLE DETECT
3	BLUE VIDEO	11	GROUND
4	GROUND	12	SDA (for DDC)
5	GROUND	13	H-SYNC
6	RED GROUND	14	V-SYNC
7	GREEN GROUND	15	SCL (for DDC)
8	BLUE GROUND

INFORMATION TO THE USER

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.

WARNING

The manufacturer is not responsible for any Radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.”

TROUBLESHOOTING

When the following troubles occur, follow the troubleshooting. Before contacting a service centre.

Troubleshooting

|

Troubleshooting Tip

---|---

The screen doesn’t show up

| 1. Make sure the power supply is connected properly
2. Turn on the power.
3. Select the input signal right for the connected port.
The screen is too light or too dark| Control the BRIGHTNESS

The screen size is not fit for the PC signal

|

Press the AUTO key among the keys in the front. (It is used only in the PC signal)

The screen color shows strange in the PC signal

|

In the FUNCTION menu of the OSD menu, perform the AUTO-ADJUST.

Warranty

2Year Limited Warranty

All Orion Images products carry a limited warranty from the ship date against defects in materials and workmanship. Orion Images is not liable for improper installation that results in damage to mounts, adapters, display equipment or personal injury.

CONTACT

Contact Orion Images

In the event of missing and/or damaged equipment, or technical questions, the following information can help in the completion of the installation.
Address: 7300 Bolsa Avenue, Westminster, CA 92683
Tel: 714-766-6300 / Fax: 714-766-6310
Email: rma@orionimages.com
Website: http://www.orionimages.com.