KingFisher T Shape Hood User Manual
- June 4, 2024
- KingFisher
Table of Contents
KingFisher T Shape Hood
IMPORTANT – These instructions are for your safety. Please read through them thoroughly prior to handling the product and retain them for future reference.
Parts
Not included
VENT PACK
(Ø150mm)
3663602843153
CARBFILT22
5063022033918
You will need
Safety
Before you start
These instructions are for your safety. Please read the following instructions
carefully before proceeding with the installation and use of this appliance.
WARNING: ALL INSTALLATION WORK MUST BE CARRIED OUT BY A SUITABLY
QUALIFIED PERSON, STRICTLY FOLLOWING LOCAL BUILDING REGULATIONS AND THESE
INSTRUCTIONS.
-
To avoid the risks that are always present when you use an electrical appliance it is important that this cooker hood is installed correctly and that you read the safety instructions carefully to avoid misuse and hazards. After unpacking the cooker hood please check that it is not damaged. If in doubt, do not use the appliance but contact Customer Services on 0800 324 7818 (UK) and 1-800 932 230 (Eire).
-
Check the package and make sure you have all of the parts listed and decide upon the appropriate location for your product. If this product contains glass please take care with fitting or handling to prevent personal injury damage to the product. The specification plate shown on this appliance displays all the necessary identification information for ordering replacement parts. If you sell the appliance, give it away, or leave it behind when you move house, please ensure that you pass on this manual so that the new owner can become familiar with the appliance and its safety warning.
-
WARNING: THERE IS A RISK OF ELECTRIC SHOCK AND FIRE IF CLEANING IS NOT CARRIED OUT IN ACCORDANCE WITH THESE INSTRUCTIONS.
-
WARNING: WHERE APPLICABLE, THIS APPLIANCE IS SUPPLIED WITH FIXINGS. PLEASE ENSURE YOU USE THE CORRECT FIXINGS SUITABLE FOR THE SUBSTRATE WHERE THE APPLIANCE WILL BE INSTALLED AND THAT THEY ARE ABLE TO SUPPORT THE WEIGHT OF THE APPLIANCE.
-
WARNING: USE ONLY THE SAME SIZE OF FITTINGS AND MOUNTING SCREWS AS RECOMMENDED IN THIS INSTRUCTION MANUAL. FAILURE FOLLOWING THESE INSTRUCTIONS MAY RESULT IN ELECTRICAL HAZARDS.
-
WARNING: SWITCH OFF THE APPLIANCE AT THE MAIN SUPPLY BEFORE CARRYING OUT ANY MAINTENANCE WORK OR CLEANING.
-
WARNING: ACCESSIBLE PARTS MAY BECOME HOT WHEN USED WITH COOKING APPLIANCES. CHILDREN LESS THAN 8 YEARS OF AGE SHALL BE KEPT AWAY UNLESS CONTINUOUSLY SUPERVISED CARE SHOULD BE TAKEN TO AVOID TOUCHING THE APPLIANCE.
-
WARNING: DO NOT FLAMBE UNDER THE HOOD. TO AVOID THE RISK OF FIRE, CLEAN OR REPLACE THE GREASE FILTER REGULARLY AND CLOSELY MONITOR PANS CONTAINING HOT OIL.
-
WARNING: MEANS FOR FULL DISCONNECTION MUST BE INCORPORATED IN THE FIXED WIRING IN ACCORDANCE WITH THE LOCAL WIRING INSTALLATION RULES FOR YOUR COUNTRY. AN ALL-POLE DISCONNECTION SWITCH HAVING A CONTACT SEPARATION OF AT LEAST 3 MM IN ALL POLES SHOULD BE CONNECTED DURING INSTALLATION.
-
WARNING: WHEN THE EXTRACTOR HOOD IS LOCATED ABOVE AN APPLIANCE, THE MINIMUM DISTANCE BETWEEN THE SUPPORTING SURFACE FOR THE COOKING VESSELS ON THE HOB, THE COOKING VESSELS ON THE HOB AND THE LOWEST PART OF THE HOOD
SHALL BE:-
GAS HOBS
≥ 760 MM -
ELECTRIC HOBS
≥ 650 MM
-
-
WARNING: BEFORE CONNECTING THE HOOD, CHECK THAT THE SUPPLIED VOLTAGE AND FREQUENCY MATCH WITH THAT INDICATED ON THE APPLIANCE RATING PLATE. FAILURE TO INSTALL THE APPLIANCE IN ACCORDANCE WITH THESE INSTRUCTIONS MAY RESULT IN A SAFETY HAZARD. IF IN DOUBT, ASK FOR ADVICE INSTORE OR FROM A QUALIFIED INSTALLER.
WARNING: CONSULT LOCAL REGULATIONS REGARDING EXTRACTION OUTLETS AND ENSURE THESE ARE COMPLIED WITH. DO NOT CONNECT THE HOOD TO A VENTILATION OR HOT AIR DUCT CONTAINING COMBUSTION FUMES FROM BURNING GAS OR OTHER FUELS. CONFIRM THAT ROOM VENTILATION IS APPROPRIATE WITH THE LOCAL AUTHORITIES. -
WARNING: THE HOOD MAY STOP WORKING DURING AN ELECTROSTATIC DISCHARGE (E.G. LIGHTNING). THIS INVOLVES NO RISK OF DAMAGE. SWITCH OFF THE ELECTRICITY SUPPLY TO THE HOOD AND RECONNECT AFTER ONE MINUTE.
WARNING: THIS APPLIANCE CAN BEUSED BY CHILDREN AGED FROM 8 YEARS AND ABOVE AND PERSONS WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES OR LACK OF EXPERIENCE AND KNOWLEDGE IF THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE IN A SAFE WAY AND UNDERSTAND THE HAZARDS INVOLVED. CHILDREN SHALL NOT PLAY WITH THE APPLIANCE. CLEANING AND USER MAINTENANCE SHALL NOT BE MADE BY CHILDREN WITHOUT SUPERVISION. KEEP THE APPLIANCE AND ITS SUPPLY CORD OUT OF THE REACH OF CHILDREN LESS THAN 8 YEARS OLD. -
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a safety hazard.
-
Do not install the appliance outdoors in a damp place or in an area which may be prone to water leaks such as under or near a sink unit. In the event of a water leak affecting the appliance, do not use and contact customer services to arrange for an inspection.
-
Do not use flammable sprays in close vicinity to the appliance.
-
Please dispose of the packing material carefully. There isa fire risk if cleaning is not carried out in accordance with the instructions. Refer to the Care and Maintenance sections carefully for details on how to clean and replace the aluminium and carbon filters (if fitted).
-
The LED lamps in this appliance are not replaceable by the consumer. If a lamp fails, please contact the customer helpline at the end of Care & maintenance to arrange an engineer visit.
-
Do not use a steam cleaner for care and maintenance.
-
The appliance is not intended to be operated by means of an external timer or separate remote control system.
-
There shall be adequate ventilation of the room when the hood is used at the same time as appliances burning gas or other fuels. Ensure that the negative pressure of the installation site does not exceed 4 Pa (0.04 mbar) to ensure combustion fumes are not drawn back into the room.
-
Do not use the hood if it shows signs of damage or imperfection. Contact customer services for assistance.
-
The manufacturer declines all liability for personal or material damage as a result of misuse or incorrect installation of this appliance.
-
The appliance is for domestic use only as an extractor hood.
Electrical Installation
All installations must be carried out by a competent person or qualified
electrician. Before connecting the mains supply ensure that the mains voltage
corresponds to the voltage on the rating plate.
Direct Connection
The appliance must be connected directly to the mains using an omnipolar
circuit breaker with a minimum opening of 3mm between the contacts. The
installer must ensure that the correct electrical connection has been made and
that it complies with the wiring diagram. The cable must not be bent or
compressed. Regularly check the power plug and power cord for damage. If the
supply cord is damaged, it must be replaced by a special cord or assembly
available from the manufacturer or its service agent.
WARNING: THIS IS A CLASS I APPLIANCE AND MUST BE EARTHED
This appliance is supplied with a 3-core mains cable colored as follows:
- Brown = L or Live
- Blue = N or Neutral
- Green and Yellow = E or Earth
This appliance should be connected directly to the consumer unit with a 3
Amp Residual Current Device (RCD) protecting its circuit.
To avoid the risks that are always present when you use an electrical
appliance it is important that this appliance is installed correctly and that
you read the safety instructions carefully to avoid misuse and hazards. Please
keep this instruction booklet for future reference and pass it on to any
future owners. Afterunpacking the appliance please check that it is not
damaged. If in doubt, do not use the appliance but contact Customer Services.
The manufacturer declines all liability for damage caused to persons and
objects due to incorrect or improper installation of the appliance. Any
permanent electrical installation must comply with the latest wiring
regulations applicable to your country and for your own safety a qualified
electrician or contractor should undertake the electrical installation. The
appliance is supplied from the factory to use external ducting (not supplied).
Should you wish to use this in recirculation mode only, please fit the correct
carbon filter (not supplied).
Technical data
Supply voltage | 220-240 V~ 50 Hz |
---|---|
Power consumption – Fan | 65 W |
Power consumption – Cooking Light | 2 x 2.5 W |
Power consumption – Total | 70 W |
Protection class | I |
ILCOSD Code – Cooking Light
| ****
DSR-2.5-S-68
Information for EU No. 66/2014 and No. 65/2014
Information of the cooker hood ( www.diy.com)
Value |
---|
Supplier’s name
| Kingfisher Int. Prod. B.V. Kingfisher Int. Prod. Ltd.
Model identification| BH60SS
Annual Energy Consumption (AEC hood) (kWh/year)| 34.7
Energy Efficiency class| C
Fluid Dynamic Efficiency| 12.2
Fluid Dynamic Efficiency class| E
Lighting Efficiency (LEhood) (lux/W)| 32.0
Lighting Efficiency class| A
Grease Filtering Efficiency (GFE hood)| 69.7
Grease Filtering Efficiency class (GFEhood)| D
Minimum air flow at working point (in normal use) (m3/h)| 214.5
Maximum air flow at working point (in normal use) (m3/h)| 318.5
Maximum air flow at highest setting (Qmax) (m3/h)| 328.7
Maximum air flow at highest setting (Qmax) (m3/h) (with Boost)| –
Weighted sound power level at minimum setting (LWA) (dB)| 59
Weighted sound power level at maximum setting (LWA) (dB)| 64
Sound power level of boost if any (LWA) (dB)| –
Measured power consumption off mode (Po) (W)| 0
Measured power consumption in standby mode (Ps) (W)| –
---|---
Time increase factor (f)| 1.6
Energy Efficiency Index (EEIhood)| 73.4
Measured air flow rate at best efficiency point (QBEP) (m3/h)| 191.9
Measured air pressure at best efficiency point (PBEP) (Pa)| 122
Measured electric power input at best efficiency point (WBEP) (W)| 53.2
Nominal power of the lighting system (WL) (W)| 5.0
Average illumination of the lighting system on the cooking surface (Emiddle)
(lux)|
160
The measurement and calculation method of the above table was done in accordance with Commission Delegated Regulation (EU) No 65/2014 & Commission Regulation (EU) No 66/2014.
egated Regulation (EU) No 65/2014 & Commission Regulation (EU) No 66/2014.
The following shows how to reduce total environmental impact (e.g. energy
use) of the cooking process.
- Install the cooker hood in a proper place where there is efficient ventilation.
- Clean the cooker hood regularly so as not to block the airway.
- Remember to switch off the cooker hood light after cooking.
- Remember to switch off the cooker hood after cooking
Information for dismantling.
This appliance cannot be dismantled by the user, other than that as shown in
the original assembly of the user manual. At the end of its useful life, the
appliance should not be disposed of with household waste. Check with your
local governmental authority, domestic waste disposal services or the retailer
where the product was bought for recycling advice.
Recycling & Disposal
Waste electrical products (WEEE) should not be disposed of with household
waste. Please recycle where facilities exist. Check with your local
governmental authority, domestic waste disposal services or the retailer where
the product was bought for recycling advice. The wheelie bin symbol on the
product or its packaging indicates that this product cannot be treated as
normal household waste. This product must be handed over to an electric and
electronic equipment collection point for recycling. On ensuring that this
product is disposed of correctly, you will help to avoid possible negative
consequences for the environment and public health, which could occur if this
product is not handled correctly.
Guarantee
We take special care to select high quality materials and use manufacturing
techniques that allow us to create products incorporating design and
durability. This cooker hood has a manufacturer’s guarantee of 2 years against
manufacturing defects, from the date of purchase (if bought in store) or date
of delivery (if bought online), at no additional cost for normal (non-
professional or commercial) household use. To make a claim under this
guarantee, you must present your proof of purchase (such as a sales receipt,
purchase invoice or other evidence admissible under applicable law), please
keep your proof of purchase in a safe place. For this guarantee to apply, the
product you purchased must be new, it will not apply to second hand or display
products. Unless stated otherwise by applicable law, any replacement product
issued under this guarantee will only be guaranteed until expiry of the
original period guarantee period. This guarantee covers product failures and
malfunctions provided the product was used for the purpose for which it is
intended and subject to installation, cleaning, care and maintenance in
accordance with the information contained in these terms and conditions, in
the user manual and standard practice, provided that standard practice does
not conflict with the user manual. This guarantee does not cover defects and
damage caused by normal wear and tear or damage that could be the result of
improper use, faulty installation or assembly, neglect, accident, misuse, or
modification of the product. Unless stated otherwise by applicable law, this
guarantee will not cover, in any case, ancillary costs (shipping, movement,
costs of uninstalling and reinstalling, labour etc), or direct and indirect
damage.If the product is defective, we will, within a reasonable time, repair.
Rights under this guarantee are enforceable in the country in which you
purchased this product. Guarantee-related queries should be addressed to the
store you purchased this product from. The guarantee is in addition to and
does not affect your statutory rights.
IMPORTANT – RETAIN THIS INFORMATION FOR FUTURE REFERENCE:
READ CAREFULLY
Installation
Mark the wall with the hole positions as shown in the diagram. The fixings
supplied are suitable for solid walls only. When fixing to any other type of
wall use suitable alternative fixings.
WARNING: Caution! Before drilling it is extremely important to check the
wall for hidden pipes and electrical cables using an appropriate detection
device. Ensure that all safety distances to flammable materials are followed
as shown above. Drill the holes, insert the wall plugs in all 9 holes. Insert
the screws in the holes in the second row from the bottom. The maximum gap
between row three and row four from the bottom should be between 78- 345mm,
dependent upon the ceiling height.
WARNING: Use only the same size of fittings and mounting screws as
recommended in this instruction manual. Failure to follow these instructions
may result in electrical hazards.
WARNING: Please follow the Safety and Electrical Installation sections at
the start of this manual before connecting this appliance to the mains supply!
Only for ducted option
Only for the recirculation option.
Tighten all screws
Use
Before you start
WARNING: Read the instructions before using the appliance. Switch on the
Residual Current Device (RCD) at the consumer unit. The appliance is ready for
use.
Functions & Settings
Control panel
To obtain the best results from your cooker hood it is recommended that you
leave it switched on for up to 15 minutes after you have finished cooking.
- Fan off button
- Fan speed 1 button
- Fan speed 2 button
- Fan speed 3 button
- Light on / off button
Troubleshooting
Problem | Possible cause | Solution |
---|
Excessive vibration.
| The appliance is not installed properly on the brackets.| Take down the
appliance and check it is properly fixed.
The fan blade is damaged.| ****
Switch off the appliance. Repair to be carried out by qualified service personnel only.
The fan motor is not fixed tightly.
The light is on, but the fan does not work.| The fan blade is jammed.
The motor is damaged.
Both the light and motor do not work.
| ****
Light bulb blown.
| Ring the customer helpline at the end of the Care & maintenance section to
arrange an engineer visit.
Power connection loose.| Check power supply.
Suction performance reduced.
| Speed may be too low.| Select a higher speed.
Aluminium filters are dirty.| Clean the aluminium filters. (See Care and
maintenance section).
Top vent might be obstructed.| Clear any obstruction.
Optional vent kit might be twisted.
| Ensure that the vent kit is fitted according to the manufacturer’s
instructions.
The installation may not comply with the manufacturers instructions.| The vent
hose should be correct diameter throughout with no reductions or restriction.
(See installation section).
Works normally but cooking smells linger.| Carbon filter is not fitted in
recirculation mode or is full of grease.| Fit carbon filter or replace the
carbon filter (See Care and maintenance section).
This appliance respects laws of the suppression of radio interference. As the Manufacturer has a policy of continuous product improvement, it reserves the right to adapt and carry out any modification considered necessary without prior warning.
Care & maintenance
WARNING: Turn off the power at the Residual Current Device (RCD) before
replacing the carbon filters.
Carbon filter replacement
Replace carbon filters every three months. To change the carbon filters:
3 MONTHS
Use two carbon filters, model CARBFILT22 5063022033918 available from the
Customer helpline. See the Care & Maintenance section for details.
WARNING: Always switch off the electrical supply before carrying out
maintenance work on the hood. In the event of a fault, contact Customer
Services.
Aluminum grease filter cleaning
Aluminum filters: To avoid fires, clean thoroughly once a month. Remove the
grease filters as shown and soak in hot water and detergent for an hour. If
using a dishwasher position the filters vertically to improve the cleaning
process.
WARNING: Increase the filter cleaning/replacement frequency if the hood is used for more than 2 hours a day. Always use genuine filters from the manufacturer.
Lamp replacement
The LED lamps in this appliance are not replaceable by the consumer. If a lamp
fails, please contact the Customer helpline to arrange an engineer visit.
Customer helpline (toll-free):
UK 0800 324 7818 uk@kingfisherservice.com
Eire 1800 932 230 eire@kingfisherservice.com
Manufacturer
- Fabricant
- Producent
- Producător
- Fabricante
UK Manufacturer:
Kingfisher International Products Limited, 3 Sheldon Square, London, W2 6PX
United Kingdom
www.diy.com
www.screwfix.com
www.screwfix.ie
Customer Helpline (Freephone)
UK 0800 324 7818 uk@kingfisherservice.com
Eire 1800 932 230 eire@kingfisherservice.com
To view instruction manuals online,
visit www.kingfisher.com/products
References
- Brico Depôt | Bricolaje, jardín, construcción y climatización
- Brico Depôt | Bricolage, construção, jardim e climatização
- Bricolage, jardinage et aménagement de la maison | Castorama
- B&Q | DIY Products at Everyday Low Prices | DIY at B&Q
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>