KINGFISHER KF400 Deluxe Warewasher User Manual

: October 30, 2023
: KingFisher

QUICK START USER MANUAL

FOR KINGFISHER DELUXE

UNDERCOUNTER GLASS & DISHWASHERS

INTRODUCTION

Welcome to your new Kingfisher Deluxe Warewasher.

This model refers to more than one type of unit in the range. For reference, refer to the product specifications overleaf to identify your appliance.

Unpacking & Positioning

This appliance is not designed to be moved by hand from area to area. It must be moved into position on a pallet with a forklift or other suitable lifting equipment before unboxing.

Upon unwrapping, inspect the machine for damage immediately. If any issues are noticed, please contact the retailer directly.

Read this user manually carefully, particularly installation instructions overleaf before attempting to use or operate the machine.

Safety Instructions

Do not use the appliance in areas without sufficient lighting.

Do not touch moving parts of the appliance whilst it is in operation.

Do not install or use the appliance in the presence of flammable or explosive materials.

Do not operate the appliance when it is not connected to a water supply

This appliance must be earthed in accordance with local regulations. All damage caused by use when not earthed will not be covered under the warranty.

If for any reason there is a malfunction of the appliance which causes a leak of water, ensure that the electrical supply is switched off at the plug/circuit breaker immediately before touching the appliance.

In the event of a malfunction of the appliance which causes fire or smoke, switch off the electrical supply at the plug/circuit breaker immediately. Do not use water to extinguish and instead use a fire extinguisher suitable for electrical fires.

For further assistance, please call our UK service partner on 01279 876 500 or write an email toservice@buzzsupplies.co.uk

PRODUCT SPECIFICATIONS

Model

| Dimensions (mm)| Weight (kg)| Packaging Dimensions
---|---|---|---
KF400| 480x580x720| 41|

590x510x880

KF500

| 590x700x820| 67|

725x650x970

Technical Information

Product Code

| KF400| KF500
---|---|---
Capacity| 1000 glasses/hour|

540 plates/hour

Basket Dimensions

| 400x400mm| 500x500mm
Total Power| 2.75kw|

3kw

Motor Power

| 0.25kw| 0.55kw
Boiler Heating| 2.0kw|

2.5kw

Tank Heating

| 2.5kw| 2.5kw
Operating Voltage| 230v|

230v

Fuse Rating

| 13A| 13A
Water Pressure| 2-4 bar|

2-4 bar

Program Timer

| 90, 120 or 180 seconds| 90, 120 or 180 seconds
Drain Pump| Yes|

Yes

GENERAL INFORMATION

Before installing or using the appliance, read this quick start user manual carefully.

Incorrect installation of the machine may damage the product, cause injury to people and invalidate your warranty. The company is not responsible for damage to the appliance because of incorrect use, negligence, wrong connections etc.

This instruction manual should be kept in a safe place for future reference
Installation should be made by a qualified service engineer
Please check for local regulations and rules about proper use & connection
The appliance is designed for commercial use & operation by trained personnel only
In the event of a malfunction or failure, turn off the appliance immediately
The appliance should only be repaired by authorised service personell.

For further assistance, please call our UK service partner on 01279 876 500 or write an email toservice@buzzsupplies.co.uk

INSTALLATION

All Kingfisher Deluxe glass washers & dishwashers are supplied with the following:

3 pin 13amp UK Plug (Pre-Installed)
Drain Hose (Pre-Installed)
Water Inlet Hose (Not Installed)
Detergent Intake Pipe (Pre-Installed)
Rinse Aid Intake Pipe (Pre-Installed)
Baskets (2)
Feet (4)

Please take care when unpacking the unit as the feet do not come preinstalled. Ensure these are installed on to the unit BEFORE moving to the location you are installing to. Once in place ensure unit is level, left to right, front to back as if not this can affect the running of the machine.

Connecting the Water Supply

The mains water hose will be supplied with the unit and located in the wash tank (Seen when retrieving the feet in the previous step).

Connect one end of the hose to the Inlet valve on the unit, ensure to NOT cross thread when screwing on to the unit. Once it has been connected tightly connect the other end of the hose to your mains water supply or water softener where applicable.

Please Note: medium to hard water areas must be connected to a water softener. Failure to do so could damage your machine, cause poor wash results and invalidate your warranty.

Connecting The Waste Outlet

The grey ribbed waste hose will need to be connected to your waste outlet.

All Kingfisher deluxe machines are fitted as standard with a drain pump. However, you must ensure the waste outlet is not higher than three quarters of the height of the unit as this will prevent the pump from operating correctly.

Using an upstand is preferred, as a spigot will reduce the flow rate and may result in dirty water flowing back into the unit.

Connecting To Electrical Supply

All machines, unless otherwise specified, are 13amp 3 pin Plug. Ensure the unit is connected to a dedicated socket with no other items that use an element on the ring.

DO NOT USE AN EXTENSION LEAD OR DOUBLE PLUG.

Connecting To Chemicals

All units will come supplied with automatic chemical dosing pumps fitted internally to the machine. The pickup for these are the two pipes at the rear of the machine.

CLEAR: for glasswash or dishwash detergent
GREEN or BLUE: for rinse aid
Please Note: If the unit has 2 clear pipes fitted, there will stickers to indicate which pipe is used for which stuck to the back of the machine where the pipe exits.

RECOMMENDED

Wash results and machine longevity can be highly dependant on the quality of chemicals used. Kingfisher has been tested with and always recommends the use of EntirePro.

It is always advisable to make a small hole in the lid of the chemicals and feed the tube through, you will need to remove the weight and filter before doing so, re attach this when the tube has gone through the lid, screwing the lid back on to the chemical bottle. Ensure the chemical dosing tube has been fed through, so it is at the bottom of the bottle. This is to prevent Oxidisation of the chemicals and provide a longer shelf life.

First Use

Ensure the power is on at the socket, the power light on the front unit will illuminate
Make sure that the Water valve has been turned on/Water softener is open to the machine
You are now ready to begin using the unit.
Turn overleaf for operating instructions.

OPERATION

Control Panel Overview

POWER
WASHING & RINSING
CYCLE SELECT
DRAINING
TEMP READY

Filling the machine

1. Using the Black Dial on the right hand side. Turn to position 1.

a) TEMP READY

2. The unit will then fill with water, after a short while this will stop at the required level and automatically start to heat the boiler and tank. This will take between 45 minutes to 1 Hour to fully heat every time you fill the unit. The chemicals will have already dispensed via the internal dosing pumps. Do not add anything to the wash tank that may interfere with this such as washing up liquid or other chemicals.
3. When both tanks are heated to their correct temperatures

Wash Tanks: 55 – 65 °C
Boiler: 75 – 85 °C

The temperature indicator light will illuminate to confirm they have reached their set

Starting a wash cycle

1. Please ensure that all items receive a pre rinse before going through the wash cycle. This is to ensure no grease/grime or excess food stuff goes into the wash tank. This will affect your wash results and possibly cause further problems.
2. Place the items in the basket ensuring there is nothing poking through the holes in the basket that may interfere with the bottom wash/rinse arm rotation.
3. Close the door and turn the Black Dial to Position 2, 3 or 4 for your preferred wash cycle. length.

4. The unit will perform the wash cycle and then a small rinse cycle.
5. Once this has completed open the door and remove the tray, closing the door to ensure there is minimal loss of heat. DO NOT PUT THE TRAY ON TOP OF THE UNIT TO DRIP DRY as this will cause electrical problems.

Draining and end of day cleaning

1. When the machine requires to be emptied, generally at the end of the day, remove the tray and release the overflow ensuring the filter remains in place until all of the water has been removed.
2. Turn the black dial to position 5

3. The drain pump will automatically start and water will begin to empty from the tank going through the drain pipe to your external waste pipe.
4. It may be necessary to perform this procedure more than once should there be a small amount of water left in the tank.
5. Once the tank has been completely emptied, please complete your daily/monthly cleaning schedule procedure.

Front Service Panel

Commonly adjusted configurations can easily be changed by the user underneath the front service panel. This can be removed by unscrewing the two screws located at the very bottom front of the machine.

Kingfisher Deluxe 400mm

Temperature controls set-up:

SCAN QR

https://youtu.be/ltMKoJNh6Es

Dosing pump adjustment set-up:

SCAN QR

https://youtu.be/gjVcHnoWffk

Kingfisher Deluxe 500mm

Temperature controls set-up:

SCAN QR

https://youtu.be/ogs8bIjPP6A

Dosing pump adjustment set-up:

SCAN QR

https://youtu.be/S2LVhBQ71Iw

EXPLODED SPARE PARTS DIAGRAM

Kingfisher Deluxe 400mm

PRODUCT CODE:EMP.1100

NO| PRODUCT NAME|

P.CODE

1

| TOP LID| Y.EMP.1100.001
2| WARNING LAMP|

Y.EMP.1100.002

3

| SWITCH| Y.EMP.1100.003
4| BALLCOCK|

Y.EMP.1100.004

5

| TOP EJECTOR| Y.EMP.1100.005
6| LID LOCK|

Y.EMP.1100.006

7

| BASKET| Y.EMP.1100.007
8| FILTER|

Y.EMP.1100.008

9

| MOTOR| Y.EMP.1100.009
10| LID LOCK PLASTIC|

Y.EMP.1100.010

11

| FRONT LID| Y.EMP.1100.011
12| BOTTOM LID|

Y.EMP.1100.012

13

| THERMOSTAT| Y.EMP.1100.013
14| DRAINAGE PUMP|

Y.EMP.1100.014

15

| DRAINAGE WEDGE BEARING| Y.EMP.1100.015
16| BOILER|

Y.EMP.1100.016

17

| BOWL RESISTANCE| Y.EMP.1100.017
18| WATER VALVE|

Y.EMP.1100.018

19

| FEET| Y.EMP.1100.019
20| AIR LOCK|

Y.EMP.1100.020

21

| BOTTOM EJECTOR| Y.EMP.1100.021
22| EJECTOR HANDLE|

Y.EMP.1100.022

23

| STOPPER| Y.EMP.1100.023
24| BASE FRAME|

Y.EMP.1100.024

25

| RINSING NOZZLE| Y.EMP.1100.025
26| WASHING NOZZLE|

Y.EMP.1100.026

27

| POLISHER PUMP| Y.EMP.1100.027
28| BOILER RESISTANCE|

Y.EMP.1100.028

29

| BOTTOM EJECTOR SHAFT| Y.EMP.1100.029
30| TOP EJECTOR SHAFT|

Y.EMP.1100.030

31

| RINSING HOSE| Y.EMP.1100.031
32| WEDGE-LEFT|

Y.EMP.1100.032

33

| WEDGE-RIGHT| Y.EMP.1100.033
34| POLISHER PUMP HOSE|

Y.EMP.1100.034

35

| BOWL PUMP HOSE| Y.EMP.1100.035
36| POLISHER BOILER HOSE|

Y.EMP.1100.036

37

| VALVE BOILER HOSE| Y.EMP.1100.037
38| BOWL DRAINAGE HOSE|

Y.EMP.1100.038

39

| TERMINAL BLOCK| Y.EMP.1100.039
40| CONTACTOR DILEM10|

Y.EMP.1100.040

41

| CONTACTOR DILEM01| Y.EMP.1100.041
42| FUSE HOLDER|

Y.EMP.1100.042

43

| GLASS FUSE| Y.EMP.1100.043
44| WASHING TIME RELAY|

Y.EMP.1100.044

45

| DRAINAGE TIME RELAY| Y.EMP.1100.045
46| DRAINAGE WATER HOSE|

Y.EMP.1100.046

47

| CLEAN WATER HOSE| Y.EMP.1100.047
48| BALLCOCK HOSE|

Y.EMP.1100.048

49

| SWITCH HOSE| Y.EMP.1100.049
50| DETERGENT INLET|

Y.EMP.1100.050

51

| EJECTOR NUT| Y.EMP.1100.051
52| WEDGE BEARING NUT|

Y.EMP.1100.052

53

| FILTER BEARING| Y.EMP.1100.053
54| BOTTOM BRACKET GASKET|

Y.EMP.1100.054

55

| BOTTOM BRACKET| Y.EMP.1100.055
56| RINSING INLET SLEEVE|

Y.EMP.1100.056

57

| LEFT BASKET SLEDGE| Y.EMP.1100.057
58| RIGHT BASKET SLEDGE|

Y.EMP.1100.058

59

| LID HANDLE SHEETMETAL| Y.EMP.1100.059
60| WEDGE PLASTIC|

Y.EMP.1100.060

61

| LID HANDLE| Y.EMP.1100.061
62| BOTTOM LID HANDLE|

Y.EMP.1100.062

63

| LID SCREW| Y.EMP.1100.063
64| RESISTANCE LID|

Y.EMP.1100.064

65

| MAGNET|

Y.EMP.1100.065

Kingfisher Deluxe 500mm

PRODUCT CODE: EMP.500

NUMBER| PRODUCT NAME|

PRODUCT CODE

1

| TOP LID| Y.EMP.500.001
2| SWITCH|

Y.EMP.500.002

3

| WARNING LAMP| Y.EMP.500.003
4| SWITCH BUTTON|

Y.EMP.500.004

5

| TOP EJECTOR| Y.EMP.500.005
6| LID HANDLE|

Y.EMP.500.006

7

| BOWL RESISTANCE| Y.EMP.500.007
8| DRAINAGE WEDGE|

Y.EMP.500.008

9

| BOILER TANK| Y.EMP.500.009
10| LID LOCK PLASTIC|

Y.EMP.500.010

11

| LID LOCK| Y.EMP.500.011
12| TOP EJECTOR HANDLE|

Y.EMP.500.012

13

| BASE FRAME| Y.EMP.500.013
14| RINSING HOSE|

Y.EMP.500.014

15

| WASHING HOSE| Y.EMP.500.015
16| BOTTOM LID|

Y.EMP.500.016

17

| FRONT LID| Y.EMP.500.017
18| DETERGENT PUMP|

Y.EMP.500.018

19

| THERMOSTAT| Y.EMP.500.019
20| WEDGE BEARING|

Y.EMP.500.020

21

| DRAINAGE PUMP| Y.EMP.500.021
22| MOTOR|

Y.EMP.500.022

23

| BOILER VALVE HOSE| Y.EMP.500.023
24| BOWL PUMP HOSE|

Y.EMP.500.024

25

| DRAINAGE HOSE| Y.EMP.500.025
26| FEET|

Y.EMP.500.026

27

| BOWL DRAINAGE HOSE| Y.EMP.500.027
28| AIR LOCK|

Y.EMP.500.028

29

| VALVE| Y.EMP.500.029
30| BOTTOM EJECTOR HANDLE|

Y.EMP.500.030

31

| DRAINAGE ADD. PIPE| Y.EMP.500.031
32| FILTER|

Y.EMP.500.032

33

| RINSING NOZZLE| Y.EMP.500.033
34| WASHING NOZZLE|

Y.EMP.500.034

35

| EJECTOR SHAFT| Y.EMP.500.035
36| BOILER RESISTANCE|

Y.EMP.600.036

37

| POLISHER PUMP| Y.EMP.500.037
38| EJECTOR NUT|

Y.EMP.500.038

39

| BALLCOCK| Y.EMP.500.039
47| FILTER HOLDER|

Y.EMP.500.047

48

| FILTER NUT| Y.EMP.500.048
49| DETERGENT INLET ATTACHMENT|

Y.EMP.500.049

EMP.500 PANO

NUMBER

| PRODUCT NAME| PRODUCT CODE
1| TERMINAL BLOCK|

Y.EMP.500.040

2

| CONTACTOR| Y.EMP.500.041
3| CONTACTOR|

Y.EMP.500.042

4

| FUSE HOLDER| Y.EMP.500.043
5| GLASS FUSE|

Y.EMP.500.044

6

| WASHING TIME RELAY| YEMP.500.045
7| DRAINAGE TIME RELAY|

Y.EMP.500.046

ELECTRIC CIRCUIT SCHEMA

Kingfisher Deluxe 400mm

P1

| S1| C1| C2| C3| C4| PR1
---|---|---|---|---|---|---
5 Progressive Commutator| Magnetic Door Sensor| Boiler Contactor 230V| Washing Contactor 230V| Lid Contactor 230V| Rinsing Contactor 230V|

Prossestat

L1

| L2| L3| L4| L5| ZR1| ZR2| V
---|---|---|---|---|---|---|---
Start lamp| Rinsing lamp| Water is heated lamp| Washing lamp| Evacuation lamp| 5 Cycle- cycle Relay (INTER RR-5TG)| 0-240 sec. cycle relay|

Solenoid valve 230V

F1

| T1| T2| M1| M2| R1| R2
---|---|---|---|---|---|---
ZR1 Fuse 500mA| Boiler thermostat (30-90°C)| Washing thermostat (30-90°C)| Washing motor 0,55 KW 230V| Evacuation motor 0,44 W 230V| Washing resistance 2500W 230V|

Boiler resistance 3000W 380V

TR1

| TR2| F1| M
---|---|---|---
Washing Motor Safety Relay (4.2.A.)| Evacuation Hose Safety Thermic (4.2.A.)| Leakage Current Safety Fuse 32 A.|

Detergent Pumps (220 V.)

Kingfisher Deluxe 500mm

P1

| S1| C1| C2| C3| C4| PR1
---|---|---|---|---|---|---
5 Progressive Commutator| Magnetic Door Sensor| Boiler Contactor 230V| Washing Contactor 230V| Lid Contactor 230V| Rinsing Contactor 230V|

Prossestat

L1

| L2| L3| L4| L5| ZR1| ZR2| V
---|---|---|---|---|---|---|---
Start lamp| Rinsing lamp| Water is heated lamp| Washing lamp| Evacuation lamp| 5 Cycle- cycle Relay (INTER RR-5TG)| 0-240 sec. cycle relay|

Solenoid valve 230V

F1

| T1| T2| M1| M2| R1| R2
---|---|---|---|---|---|---
ZR1 Fuse 500mA| Boiler thermostat (30-90°C)| Washing thermostat (30-90°C)| Washing motor 0,55 KW 230V| Evacuation motor 0,44 W 230V| Washing resistance 2500W 230V|

Boiler resistance 3000W 380V