Planet Technology HDP-1261PT 1080p SIP Vandalproof Door Phone Installation Guide

June 16, 2024
Planet Technology

1080p SIP Vandalproof Door Phone with
RFID and PoE
HDP-1261PT
Quick Installation Guide

Package Contents

Thank you for purchasing PLANET SIP Vandalproof Door Phone, HDP-1261PT.
Open the box of the SIP Vandalproof Door Phone and carefully unpack it. The box should contain the following items:

SIP Vandalproof Door Phone x 1| Quick Installation Guide QR Code Sheet x 1| Wall-mounted Kit x 1
---|---|---
| |
Mounting Template x 1| RFID Card x 2| Screw Kit x 1
| |

If any item is found missing or damaged, please contact your local reseller for replacement.

Physical Specifications

Model Dimensions
HDP-1261PT 88 x 36.15 x 177.4 mm

2.1 Wall-mounted Kit

Product Appearance Descriptions

3.1 Panel

3.2 Interface
Open the rear case of the device where there is a row of terminal blocks for connecting power supply, electric lock control, etc. The connection is as follows:

Serial number Description
1 Ethernet interface: standard RJ45 interface, 10/100M adaptive (It is

recommended to use CAT5 or CAT5E network cable.).
2| 3 short-circuit input detection interfaces for connecting switches, infrared probes, door magnets, vibration sensors and other input devices.
3| Wiegand interface
4| RS485 interface (Reserved for future use)
5| Power interface: 12V/1A input up positive, down grounded
6, 7| 2 short-circuit output control interfaces for controlling electric locks, alarms, etc.
8| Line out interface

3.3 Wiring Instructions:
NO: Normally Open Contact;
COM: Common Contact;
NC: Normally Close Contact.

Driving mode Electric-lock Mode Connections
Passive No electricity when open Electrify when open

Wall-mount Installation

Planet Technology HDP 1261PT 1080p SIP Vandalproof Door Phone - Installation
1

Figure 4-1: Three Major Parts of HDP-1261PT (Main Body, Back Shell and Wall Bracket)

Step 1: Installation preparation
A. Check the following contents:

  • KM3*6 screws x 3
  • TA4*30mm screws x 5
  • φ6*30mm screw anchors x 5
  • PM4*16mm screw x 3
  • TM6*20mm screw x 3

B. Tools that may be required:

  • Phillips screwdriver, hammer, RJ45 crimper
  • Electric impact drill with an 8mm drill bit

Step 2: Drilling

A. Place the mounting template with dimensions on the surface of a wall in a desired flat position.
B. Use an electric drill to drill the 4 holes marked on the mounting template. It is recommended to drill about 50mm deep. Remove the template when finishing drilling.
C. Push or hammer wall anchors into the drilled holes.

Step 3: Removing hanging bracket and back panel
A. Detach the wall bracket downward from the device and loosen the four screws on the rear cover with a screwdriver, as shown in Figures 4-3-a and 4-3-b.

Planet Technology HDP 1261PT 1080p SIP Vandalproof Door Phone - Installation
3

Step 4: Install the wall bracket, wiring and casing
A. Align the screw holes of the wall bracket with the holes in the wall and fix them to the wall with the screws, as shown in Figure 4-4.
B. Pass all the wires through the silicone plug in the middle of the bottom case.
The length of all the lines should be 15 to 20 cm, as shown in Figure 4-5.

The outlet hole of the bottom case faces down.

Planet Technology HDP 1261PT 1080p SIP Vandalproof Door Phone - Installation
4

C. Connect the cables of RJ45, power, and electric-lock to the motherboard socket as mentioned in connector description.
D. Connect the terminal of the wired cable to the motherboard socket.
E. Test whether there is electricity by doing the following: Press the DSS key button for 3 seconds to get the IP address of intercom by voice.
Input access password or press the indoor switch to check electric-lock installation.
Do not proceed mounting until you have finished the electric checking.
F. Attach the device to the wall bracket in a top-down manner, locking the screws at the Bottom, as shown in Figure 4-6.

Searching Door Phone

There are two methods as shown below to search the HDP-1261PT.
Method 1:
Open the Planet SmartDiscoveryLite Utility. Press the Refresh button to search the HDP-1261PT and find the IP address.

Planet Technology HDP 1261PT 1080p SIP Vandalproof Door Phone - Searching
Door Phone 1

Method 2:
Long-press DSS key for 3 seconds after powering on for 30 seconds, and when the speaker beeps rapidly, press the speed-dial button within 5 seconds, and the system will automatically announce the IP address by voice.
In addition, device provides the device surface DSS key operation to switch IP address acquisition mode: Touch and hold the speed-dial button for 3 seconds, wait for the speaker to beep, press the speed-dial button three times within 5 seconds, and the system will automatically announce the IP address by voice after successfully switching to the network mode.

Starting Web Management and Door Phone Setting

Step 1: Log in the web setting page of door phone
Enter the IP address of the door phone (e.g., https://172.16.0.1) in the address bar using the https method of your PC’s web browser.
The default user name and password are admin and 123, respectively

Step 2: Add the SIP account.
Set SIP server address, port, user name, password and SIP user with assigned SIP account parameters.
Select “Activate”, and then click Apply to save this setting.

Planet Technology HDP 1261PT 1080p SIP Vandalproof Door Phone - Starting Web
Management 2

Step 3: Setting DSS key
Set the DSS key as shown below for a quick start. Click “Apply” to save this setting.
Type: Memory Key.
Value: The DSS Key will dial to this value.
+ : If value is unavailable, it will be forwarded to another value.
Line: Working line.
Subtype: Speed dial.

Planet Technology HDP 1261PT 1080p SIP Vandalproof Door Phone - Starting Web
Management 3

Step 4: Door Phone Setting

Planet Technology HDP 1261PT 1080p SIP Vandalproof Door Phone - Starting Web
Management 4

Door Unlocking Setting

RFID Card
Step 1: Access control settings on web page →EGS Setting →Add Card Rule → Select “Type” (“Normal” card provides door opening function, “Add” card and “Del” card provides add and delete card function, Default “Normal” card)
Step 2: Enter your name and card number (just enter the first 10 digits of the card number), and click “Add” to add the card to the list.
Step 3: Access the card reading area of the device through the configured ID card to open the door.

Planet Technology HDP 1261PT 1080p SIP Vandalproof Door Phone - Door
Unlocking Setting 1

Remote Password
Step 1: Set access control on the web page → EGS Setting → Password → Add password rule → Select “Remote“
Step 2: Enter the Name, Password and Number. Press Add to Password Table.
Step 3: The owner answers the access control call and presses “ * “ (default password) or “123456” (new password) to open the door for visitors.

Planet Technology HDP 1261PT 1080p SIP Vandalproof Door Phone - Door
Unlocking Setting 2

Customer Support

Thank you for purchasing PLANET products. You can browse our online FAQs resource and User’s Manual on PLANET Web site first to check if it could solve your issue. If you need more support information, please contact PLANET VoIP support team.
PLANET online FAQs: http://www.planet.com.tw/en/support/faq
PLANET VoIP team mail address:support_voip@planet.com.tw
HDP-1261PT User’s Manual: https://www.planet.com.tw/en/support/downloads?&method=keyword&keyword=HDP- 1261PT&view=3#list

Planet Technology HDP 1261PT 1080p SIP Vandalproof Door Phone -
qr https://www.planet.com.tw/en/support/downloads?&method=keyword&keyword=HDP- 1261PT&view=3#list
Copyright © PLANET Technology Corp. 2023.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Planet Technology User Manuals

Related Manuals