SABRENT DS-UFNC USB Type-C Flat Docking Station User Guide
- June 16, 2024
- Sabrent
Table of Contents
USB Type-C Flat Docking Station for M.2 PCIe NVMe +
SATA 2.5”/3.5” SSD & HDD with Offline Clone Function
DS-UFNC / USER MANUAL
PRODUCT OVERVIEW
A: 12V DC input jack
B: Power button
C: USB 3.2 (10Gbps) Type-C por t
D: Clone direction switch| E: Clone start button
F: SATA bay / SATA bay cover
G: M.2 socket / M.2 heatsink
---|---
PACKAGE CONTENT
- Docking station
- Power adapter
- USB Type-C and Type-A to Type-C cables
- Thermal pad
- User manual
PRODUCT INFORMATION
-
Sleek and engineered to assist with heat dissipation during the cloning process.
-
The tool-free insertion/extraction process makes the dock simple to use.
-
Supports multiple M.2 SSD form factors including 2242, 2260, and 2280.
-
USB 3.2 (10 Gbps) transmission rate for responsiveness.
-
Supports M.2 PCle NVMe drives via two PCle 3.0 lanes.
-
Supports the SSD TRIM and UASP functions.
-
The downlink supports both PCle and SATA interface protocols simultaneously.
Both drives may be displayed and accessed at the same time. -
Uses the USB Type-C interface for convenience.
-
Supports bidirectional cloning via the cloning direction switch.
-
Has four LED indicators to indicate cloning progress in real time.
-
Plug and play with no drivers required. Hot-swappable.
PRODUCT FUNCTION
Powering on and off: To turn the unit on, tap the power button. To power
the unit off, hold the power button for 2-3 seconds.
Offline cloning function: Press and hold the clone button for 3-5 seconds
until all LEDs begin to blink, then quickly double-tap the clone button to
start cloning.
Note: Before cloning, confirm that the source drive is equal to or
smaller in capacity than the destination drive within the cloning pair.
Additionally, double-check the direction of the clone switch, otherwise an
error may result in accidental data loss.
LED LIGHT STATUS
- Power light – blue. Always on when the power is on.
- Clone progress indicator – blue, with four sections. Each section indicates 25% progress of the cloning process with all four lit upon 100% completion.
- SATA and M.2 drive lights – blue, and independent. Will be lit when a drive is inser ted. Will flash during read/write access. The light will turn off automatically for sleep mode after 30 minutes of idling.
Note: If the destination drive is smaller than the cloned source drive the clone progress indicator will fill and an error will be reported with two flashes.
DRIVE INSTALLATION
Lift open the M.2 SSD
heatsink cover as shown above to access the M.2 M Key socket, readying it for
drive installation
As shown in the
picture above, insert the M.2 SSD at a slight angle into the M.2 socket of the
docking station; please pay attention to the position of the keying gap and do
not insert the drive forcefully 
Close the heatsink door to complete the installation;
connect the USB cable to supply power and access the drive
Open the 2.5”/3.5” drive bay and insert the SSD or
HDD into the bay in the correct orientation to match the connectors; when
using a 3.5” HDD the docking station must have the power adapter connected
NOTICH
- When using this product during an M.2 SSD installation please be careful to avoid static electricity discharge on the drive (it is recommended to place your hands on a metal object to safely discharge before handling).
- This product uses the M Key interface which belongs to the NVMe protocol. When installing the M.2 SSD for this product please make sure the drive is NVMe with the proper keying.
- Only install the M.2 SSD when the power is off and the USB cable is disconnected.
- When inserting the 2.5”/3.5” SSD or HDD please be careful to insert gently to avoid damaging the connectors.
- When disassembling and installing the docking station please treat all accessories with care in order to prevent their loss.
- When using both bays simultaneously, whether for accessing or cloning, make sure to connect the power adapter. The USB connector on its own can only supply enough power for a single drive.
- Use the ”safely remove hardware” functionality of the operating system before unplugging the docking station from the computer.
FREQUENTLY ASKED QUESTIONS (FAQ)
1. Why is performance slow, not reaching the read and write speed of USB 3.1 Gen 2 on my system?
Answer: This product has undergone rigorous testing and the read and write speed can reach USB 3.1 performance under normal read and write conditions. If the read and write speeds are slow, it is recommended to confirm whether the USB host port you are connected to is capable of 1 0Gbps speeds; if not, speeds will be limited to USB 3.0 or 2.0 depending on the por t type.
2. Under Windows, after the new drive is installed, why can’t I find the drive or the corresponding drive letter in “My Computer”?
Answer: When using a new drive for the first time you need to initialize, format, and par tition the newly added disk in “Disk Management” under “Computer Management” before the drive can be accessed normally.
3. Why can’t the Windows XP system recognize a drive with a capacity of more than 2TB?
Answer: Due to the operating system limitation of Windows XP, the drive capacity that can be recognized on the system cannot exceed 2TB. Larger drives are only supported by computers using 64-bit Windows Vista or higher. It is recommended to convert the disk to a GPT disk, otherwise drive par titions larger than 2TB will not be supported.
4. How do I protect the drives and their data after use?
Answer: It is recommended that the user utilize the “safely remove hardware” functionality of the operating system before disconnecting the docking station.
5. Can NVMe protocol SSDs be used in Windows prior to version 8.1?
Answer: Windows 7/8 host systems may need to install an NVMe suppor t patch. Windows 8.1 and later versions have an integrated NVMe driver.
- Why can only one drive be seen in “My Computer” after the cloning procedure?
Answer: After the hard disk is cloned the identification ID of the drives are exactly the same and the operating system can only recognize one at a time. The other drive will be displayed as offline in Disk Management.
- Can this product be used to clone an operating system?
Answer: This product is based on a drive hardware clone which does not affect the use of the operating system after successful cloning. However, due to changes in the operating conditions of the hardware and software environments after cloning, the incompatibility of the driver may cause an operating system boot failure. For problems that do not belong to this product, please seek third-party technical suppor t for solutions. For example, after cloning the operating system SSD of the original SATA protocol to an NVMe SSD, the operating system driver may be incompatible, a situation outside the technical support scope of this device. You need to enable the NVMe function according to your own computer motherboard and/or solve the driver compatibility of the operating system. In addition, drive encryption and identification-locking systems may cause issues that are not a technical fault of the device; please consult the system administrator.
- How does sleep work on this device?
Answer: This device enters a sleep state after 30 minutes of no reading or writing by default, and automatically wakes up when there is a reading or writing operation again, all without manual intervention. However, if the operating system itself has a hibernation policy, this device will preferentially obey the operating system which may be inconsistent with the 30-minute hibernation time of this device; this is a normal phenomenon.
FOR HELP COMMENTS, QUESTIONS OR CONCERNS
PLEASE CONTACT OUR TECH SUPPORT TEAM VIA OUR WEBSITE
WWW.SABRENT.COM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>