Silonn SLIM24B Ice Maker Instruction Manual

INSTRUCTION
MANUAL Rev03
SLIM24B/SLIM24T/
SLIM24BU
Ice Maker

IMPORTANT SAFETY INFORMATION

To reduce the risk of injury or property damage, please follow these safety precautions.
WARNING

• Voltage power from outlet must match specifications on appliance nameplate.
• This appliance must be grounded.
• Using an extension cord may cause overheating and increase the risk of fire.
  If an extension cord MUST be used:

1. Only use an extension cord with grounding plug.
2. The marked rating of an extension cord must be equal to or greater than the rating of this appliance.

• Do not operate if any component, including the cord or plug, is damaged.
• Unplug the unit before cleaning by hand.
• Only responsible and capable adults should operate the ice maker.
• Do not place the power cord where it could be pulled by children or pose a tripping hazard.
• Children should not be left unattended near the ice maker during operation.
• Do not use water that is micro-biologically unsafe or of un- known quality.
• Do not remove any safety, warning, or product information labels from the unit.
• Do not touch the evaporator with your hands while the ice maker is operating.
• Do not plug in or unplug the unit with wet hands.
• The unit must be placed and set up according to installation instructions before use. The unit is for indoor household use only.
• Do not store or use flammable vapors or liquids near the unit.
• Do not immerse any part of the unit in water.
• Do not attempt to disassemble, repair, modify or replace any part of the ice maker unless permitted by the manufacturer.

WARNING
FIRE OR EXPLOSION HAZARD Flammable Refrigerant This unit contains an isobutane refrigerant, also known as R600a, a natural gas with high environmental compatibil-ity. However, it is also combustible. Adhere to the warnings below to reduce the risk of injury or property damage.

1. When handling, installing, and operating the unit, care should be taken to avoid damage to the refrigerant tubing.
2. Only dispose of the unit according to Federal and Local Reg­ ulations. Contact your local authorities for the environmen­ tally safe disposal of the unit .
3. Keep ventilation openings around the unit’s enclosure clear of obstruction.
4. Do not place the unit near heat sources such as an oven.
5. Ensure a minimum of three inches of clearance around the side and back walls of the unit for proper air circulation.
6. Do not place the unit in direct sunlight.

PRODUCT INTRODUCTION

Tip: To remove the cover, place your fingers in the small opening under the left side and carefully pull up.

1. Removable Top Cover
2. Secondary Water Reservoir
3. Ice Full Sensor
4. Ice Outlet
5. Water Reservoir
6. Control Panel
7. Air Exhaust Fan
8. Drain Plug
9. Maximum Water Fill Line
10. Filter
11. Ice Basket
12. Ice Scoop

CONTROL PANEL INTRODUCTION

3 times, then turn off.
Short press the ICE/CLEAN button to start making ice. The ring indicator light will turn white.
SELF-CLEANING| After the ring indicator light flashes white 3 times, the ice maker enters standby mode.
In standby mode, press and hold the ICE/ CLEAN button for 3 seconds and the ice maker will switch to self-cleaning mode.
The ring indicator light will turn blue.
ICE FULL| The ring indicator light turns green when the ice basket is full.
ADD WATER| The ring indicator light turns red when the water reservoir is low.

USING YOUR ICE MAKER

BEFORE FIRST USE HOW TO USE YOUR ICE MAKER

CLEANING AND MAINTENANCE

To keep your ice tasting fresh and the unit looking great, we recom­ mend cleaning the unit once per week.
SELF-CLEANING (15-MIN PROCESS) MANUAL CLEANING
Turn off the unit and disconnect from power outlet before cleaning.
Remove the top cover and basket.
Clean the water filter, ice outlet and both water reservoirs using a soft cloth dampened with warm water and vinegar, then rinse with clean water. ****DO’s & DON’Ts while cleaning and maintaining

• Do not use organic solvent, boiled water, detergent, strong acid and strong alkali etc. for cleaning.
• When the unit is not to be used for a long duration, drain the water completely&. dry the interior.
• Store in a well-ventilated area.

PRODUCT SPECIFICATIONS

(287 x 226 x 328 mm)

TROUBLESHOOTING

making ice, refill water, press ICE/CLEAN button, then restart and try again.
The ring in-dicator light turns green.| There is too much ice.| Remove some ice.
If there are no ice cubes, there may be an obstruction or the inner wall needs cleaning| Remove the obstruction inside or clean the inner wall of the ice storage.
The ring indicator light flashes in red.| The ambient water temperature in the inner tank is too high.| Please run the ice maker when the ambient temperature is below 90°F and pour colder water into the tank.
Refrigerant liquid leakage.| Press the ICE/CLEAN button twice to restart the ice-Making program. If this  problem shows up again, please contact customer service.
The cover motor is broken.
The pipe in the cooling system is blocked
Making Ice too slowly.| Hot air outlet has been blocked by something.| Hot air outlet must be guaranteed to have more than 6 inches of ventilation distance.
The water temperature in the inner tank is too
high.| Water temperature requirement between 45°F -90°F.
Refrigeration system malfunctions.| Please contact customer service.
Water leakage.| The drain plug is not in place.| Put the drain plug in place.
Pipe joints in the appliance may be loose.| Please contact customer service.
The seal has reached the end of its service life.

WARRANTY INFORMATION

30-DAY LIMITED WARRANTY
To provide customers with a quality shopping and user experience, the unit can be replaced or returned for a full refund within the 30-day period from the date of purchase.
30-DAY TO 1-YEAR LIMITED WARRANTY
After the 30-day warranty has expired, a 1-year warranty from the date of purchase that covers product replacement is automatically activated. Please note that proof of purchase is required for all warranty claims.
30-DAY TO 1-YEAR WARRANTY LIMITATIONS
This warranty does not cover:
-Any condition resulting from incorrect or inadequate maintenance or care.
– Damage resulting from misuse, abuse, negligence, accidents, or shipping damage.
– Dissatisfaction due to buyer’s remorse.
– Normal wear and tear.
– Damages incurred after initial transportation.

860-01986-00 Rev03
help_service_center@outlook.com
877-201-4016

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>