Cloudy Bay LJD005SMWH-6PK 3-Inch Smart LED Recessed Down Light Instruction Manual

INSTALLATION INSTRUCTIONS
LJD005SMWH-XXPK

Thank you for purchasing C/oudyBay Smart LED Lighting Fixtures.
3 INCH SMART LED RECESSED DOWNLIGHT

GENERAL: All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections, contact and obtain the services of a qualified electrician. Use UL or IEC-approved wire only for input/output connections. Remove fixture and mounting components from the box, and make sure that no parts are missing, by referencing the illustration in the illustration instructions.
**** Turn the power off before installation, inspection, or removal. Use all necessary precautions while performing this procedure. Consult a qualified electrician to ensure the correct branch circuit conductor. Min 90°C supply conductors. Properly ground electrical enclosure. IT IS IMPERATIVE THAT THE OUTLET BOX BE PROPERLY GROUNDED. DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS, OTHERWISE, SAFETY WILL BE COMPROMISED. Contact us through [email protected]

TROUBLESHOOTING

• Check that the line voltage is correct.
• If there is no voltage, then check all connections.
• Check that the junction box is grounded properly.
• If the light kit does not light:
  Check the wire connection between the junction box and the light kit is correct

CLEANING AND MAINTENANCE:

CAUTION: Ensure fixture temperature is cool enough to touch.
DO NOT clean or perform maintenance while fixture is energized.

• Clean lens and fixture with a non-abrasive cleaning solution.
• Do not open fixtures to clean LED. Do not touch the LED.
• Do not spray liquid directly on to LED, LED driver or wiring.

3-Year Limited Warranty

LIMITED WARRANTY: This fixture is warranted to be free from defects in workmanship and material for up to 3-years. Based upon reasonable household usage, when used in accordance with the package and included instructions. If this fixture does not last for the time period guaranteed, manufacturer will send you a replacement fixture upon receipt of the returned fixture, register the receipt, and proof of purchase. To contact us, please email us at [email protected] to find out how to return the fixture. We are committed to making high-quality products. Returning the fixture will help us monitor and further improve product quality. This replacement is the sole remedy available, and LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED.

PACKAGE CONTENTS

|
---|---
|

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

INSTALLATION OVERVIEW

1. Turn off power at the source.

2. Make a hole in the ceiling with a template in the package

3. Carefully remove the knock-out with a screwdriver or punch.

4. Open the connector’s box cover the Feed supply wire into the knockout hole using the connector and make all connections inside the junction box using the EZ  connectors (see picture below). Connect the 120y lie wire to the black wire. Connect the neutral wire to the white wire. Connect a bare copper wire to the grounding terminal of the outlet box. Put on the junction box cover

5. Raise clips to a vertical position and insert the light into the hole until the light fix properly above the ceiling.

6. See user manual to set up those lights

Note: This product is a smart light, using Direct Digital Controls rather than Triac dimming. Here is two dimming way for your reference. 1. Download Cloudy Bays APP, go to product group or single product page, and adjust the brightness and CCT of white light or color light on the control panel; you can also go to the home page, dick product group or single product’s common function, adjust brightness and color temperature 2. Control with smart voice devices such as Google Assistant or Amazon Alexa if you have installed it successfully.
**** :If you only have a dimmer at hand, set it to the highest level only. If light performance is not good, we strongly advise you to change it to a regular switch.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>