KICHLER 52653NI Aviv 1 in 1 Light Brushed Nickel Modern/Contemporary Vanity Light Instruction Manual

June 16, 2024
KICHLER

KICHLER 52653NI Aviv 1 in 1 Light Brushed Nickel Modern/Contemporary

Vanity Light

FIXTURE DIAGRAM

PARTS LIST

  • [A] Mounting Plate
  • [B] Outlet Box (not supplied)
  • [C] Plate Mounting Screw (2)
  • [D] Canopy
  • [E] Mounting Screw (2)
  • [F] Glass Shade

CAUTIONS
CAUTION – RISK OF SHOCK: Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

WARNING:

  1. This fixture is intended for installation by the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING:

  • Always be certain that the electric current is turned off before cleaning.
  • Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

INSTALLATION INSTRUCTIONS

  1. Attach the mounting plate[A] to the outlet box[B] using the plate mounting screws[C]. The mounting plate can be adjusted to suit the position of the fixture.

  2. NOTE: The mounting plate should be installed with the flat side of the mounting plate against the wall.

  3. NOTE: The mounting plate should be installed with the bent flanges at the
    outer edge of the mounting plate pointing away from the wall, at the 12
    and 6 o’clock position.

  4. Grounding instructions: (See Illus. a or b).

  5. a. On fixtures where the mounting plate is provided with a hole and two raised dimples, wrap ground wire from the outlet box around the green ground screw, and thread it into the hole.

  6. b. On fixtures where a cupped washer is provided, attach the ground wire from the outlet box under the cupped washer and green ground screw, and thread it into the mounting plate.
    If the fixture is provided with ground wire, connect the fixture ground wire to the outlet box ground wire with a wire connector after following the above steps. Never connect ground wire to black or white power supply wires.

  7. Make wire connections. Reference the chart below for correct connections and wire accordingly
    Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)

Connect Black or Red Supply Wire to: Connect White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black without Tracer Clear, Brown, Gold or Black with

Tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor

4.  **NOTE:** Fixture can be mounted with glass shade[F] in the up or down position.  

Push canopy[D] to the wall, carefully aligning the mounting screw holes in the mounting plate with the mounting screw holes in the canopy.
NOTE: Make sure all wires are inside the canopy and do not get pinched between the mounting plate and canopy or wall and canopy of the fixture.

5. Screw two (2) mounting screws[E] into holes in the canopy and mounting plate to attach the fixture to the wall. Tighten to secure.  

NOTE: Install one (1) at the top and one (1) at the bottom of the canopy.

6. Insert recommended bulb(s) (not included).
7. Carefully pass glass shade[F] over the installed bulb and rotate into the fixture (clockwise) until snug. DO NOT OVERTIGHTEN.

For warranty information please visit: kichler.com/warranty

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

KICHLER User Manuals

Related Manuals