KICHLER 52654NI Aviv 2 in 2 Light Brushed Nickel Modern/Contemporary Vanity Light Instruction Manual

: June 16, 2024
: KICHLER

Table of Contents

FIXTURE DIAGRAM
PARTS LIST
CAUTIONS
INSTALLATION INSTRUCTIONS
WARRANTY
CUSTOMER SUPPORT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KICHLER 52654NI Aviv 2 in 2 Light Brushed Nickel Modern/Contemporary Vanity Light

FIXTURE DIAGRAM

NOTE:
BULBS NOT INCLUDED

PARTS LIST

[A] Mounting Plate
[B] Outlet Box (not supplied)
[C] Plate Mounting Screw (2)
[D] Canopy
[E] Mounting Screw (2)
[F] Glass Shade (2)

CAUTIONS

CAUTION – RISK OF SHOCK:
Disconnect Power at the main circuit breaker panel or main fuse box before starting and during the installation.

WARNING:

This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING:

Always be certain that electric current is turned off before cleaning.
Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

INSTALLATION INSTRUCTIONS

Attach mounting plate [A] to outlet box [B] using the plate mounting screws [C]. Mounting plate can be adjusted to suit position of fixture.
NOTE: Mounting plate should be installed with the flat side of the mounting plate against the wall.
NOTE: This fixture can be installed vertically or horizontally.
For VERTICAL installation, mounting plate should be installed with the bent flanges at the outer edge of the mounting plate pointing away from the wall, at the 12 and 6 o’clock position.
For HORIZONTAL installation, mounting plate should be installed with the bent flanges at the outer edge of the mounting plate pointing away from the wall, at the 9 and 3 o’clock position.
Grounding instructions: (See Illus. a or b).
a. On fixtures where mounting plate is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.
b. On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting plate.
If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires.
Make wire connections. Reference chart below for correct connections and wire accordingly.
Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
---|---
Black| White
Parallel cord (round & smooth)| Parallel cord (square & ridged)
Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor
*Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)|
Push canopy [D] to wall, carefully aligning the mounting screw holes in mounting plate with the mounting screw holes in canopy.
NOTE: Make sure all wires are inside canopy and do not get pinched between mounting plate and canopy or wall and canopy of fixture.
Screw two (2) mounting screws [E] into holes in canopy and mounting plate to attach fixture to wall. Tighten to secure.
NOTE: For VERTICAL installation, install one (1) at the top and one (1) at the bottom of canopy. For HORIZONTAL installation, install one (1) on the left side and one (1) on the right side of canopy.
Insert recommended bulb(s) (not included).
Carefully pass glass shade [F] over the installed bulb and rotate into the fixture (clockwise) until snug. DO NOT OVERTIGHTEN. Repeat for remaining glass shade.