KICHLER 52645CPZ Palta 48 Inch 10 Light Linear Chandelier Instruction Manual

: June 16, 2024
: KICHLER

Table of Contents

FIXTURE DIAGRAM
PARTS LIST
CAUTIONS
INSTALLATION INSTRUCTIONS
WARRANTY
CUSTOMER SUPPORT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KICHLER 52645CPZ Palta 48 Inch 10 Light Linear Chandelier

FIXTURE DIAGRAM

PARTS LIST

[A] Stems, (2-6” Stems, 2-12” Stems with Short Threaded Tubes[B] attached)
[B] Short Threaded Tubes
[C] Coupling [D] Strap Mounting Screw(Qty. 2)
[E] Mounting Strap
[F] Canopy
[G] Mounting Screw (Qty. 2)
[H] Outlet Box (not supplied)
[I] Hex Nut (Qty. 2)
[J] Small Lock Washer (Qty. 2)
[K] Knob (Qty. 2)
[L] Swivel (Qty. 2)
[M] Inspection Cable
[N] Large Lock Washer (Qty. 2)
[O] Reinforcement Plate

CAUTIONS

CAUTION – RISK OF SHOCK:
Disconnect Power at the main circuit breaker panel or main fuse box before starting and during the installation.

WARNING:

This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING:

Always be certain that electric current is turned off before cleaning.
Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

INSTALLATION INSTRUCTIONS

On side of fixture with fixture wires, pass fixture wires from coupling [C] through desired number of short threaded tubes [B] and stems [A]. Screw stems together using short threaded tubes.
NOTE: A minimum of one (1) 6-inch stem must be used when mounting fixture.
NOTE: Thread locking compound must be applied to all stem threads as noted with symbol (4) to prevent accidental rotation of fixture during cleaning, relamping, etc.
On side of fixture without fixture wires, screw a second set of stems together using short threaded tubes (same number of stems and short threaded tubes as in Step 1, but without fixture wires).
On side of fixture with fixture wires, screw first stem of connected set of stems into coupling [C]. Repeat on side of fixture without fixture wires for the second set of connected stems.
On both sides of fixture, unscrew hex nuts [I] from threads protruding into canopy [F]. Retain hex nuts.
Remove large lock washers[N], inspection cable [M], and reinforcement plate [O] from threads inside of canopy. Carefully remove swivels [L] from bottom of canopy. Retain large lock washers, inspection cable, reinforcement plate, and swivels.
On side of fixture with fixture wires, pass fixture wires through swivel [L] and screw swivel into last stem. Note direction of swivel in accordance with ceiling. The swivels will help with mounting fixture to a sloped/vaulted ceiling.
On side of fixture without fixture wires, screw swivel into last stem.
NOTE: The 2nd swivel should be installed in the same direction as the 1st swivel.
Carefully lower reinforcement plate [O] back into canopy [F], aligning the holes in the reinforcement plate with the holes in the canopy.
On side of fixture with fixture wires, carefully pass fixture wires and threads at top of swivel through holes in bottom of canopy and reinforcement plate. On side of fixture without fixture wires, carefully pass threads at top of swivel through holes in bottom of canopy and reinforcement plate.
On side of fixture with fixture wires, pass fixture wires through bracket on end of inspection cable. Pass bracket on end of inspection cable over swivel threads protruding through reinforcement plate.
Pass fixture wires through large lock washer. Slip large lock washer over swivel threads.
Pass fixture wires through hex nut. Thread hex nut onto swivel threads. Tighten to secure hex nut, large lock washer, inspection cable, reinforcement plate, and canopy to swivel.
On side of fixture without fixture wires, slip large lock washer over swivel threads.
Thread hex nut onto swivel threads. Tighten to secure hex nut, large lock washer, reinforcement plate, and canopy to swivel.
Cut fixture wires a MINIMUM of 20 inches from the top edge of canopy.
Find the appropriate threaded holes in mounting strap[E] that align with hole distance in canopy.
Assemble mounting screws [G] into threaded holes in mounting strap, starting from the outlet box side.
Attach mounting strap to outlet box [H] using the strap mounting screws [D]. Mounting strap can be adjusted to suit position of fixture.
Attach inspection cable [M] to the mounting strap or to the inside of the outlet box and secure into place to prevent damage to the wires during wiring.
Grounding instructions: (See Illus. a or b).
a. On fixtures where mounting strap is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.
b. On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting strap.
If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires.
Make wire connections. Reference chart below for correct connections and wire accordingly.
Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
---|---
Black| White
Parallel cord (round & smooth)| Parallel cord (square & ridged)
Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor
*Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)|
Raise canopy to ceiling, carefully passing mounting screws through mounting screw holes in reinforcement plate and canopy.
NOTE: Be certain wires do not get pinched between mounting strap and canopy or canopy and ceiling.
Use small lock washers [J] and knobs [K] to secure canopy. Tighten to secure.
Install the recommended bulbs (Not supplied).