KICHLER 55175CPZ Adani Modern/Contemporary Vanity Light Instruction Manual

KICHLER 55175CPZ Adani Modern/Contemporary Vanity Light Instruction

Product Information

Specifications

• Product Name: Fixture
• Model Number: IS-55175-US
• Manufacturer: Kichler
• Phone Number: 866-558-5706
• Operating Hours: Monday to Friday, 9am to 5pm EST

Parts List

• [A] Knob (2)
• [B] Lock Washer (2)
• [C] Strap Mounting Screw (2)
• [D] Mounting Strap
• [E] Mounting Screw (2)
• [F] Socket Ring
• [G] Outlet Box (not supplied)
• [H] Canopy
• [I] Glass Shade
• [J] Socket
• [K] Socket Base

Installation Instructions

1. Remove lock-up knobs [A] and lock washers [B] from mounting screws [E]. Retain knobs and lock washers.
2. Attach the mounting strap [D] to the outlet box [G] using the strap mounting screws [C]. Mounting strap can be adjusted to suit the position of the fixture.
3. Grounding Instructions:
   • a. On fixtures where the mounting strap is provided with a hole and two raised dimples, wrap the ground wire from the outlet box around the green ground screw and thread it into the hole.
   • b. On fixtures where a cupped washer is provided, attach the ground wire from the outlet box under the cupped washer and green ground screw, and thread it into the mounting strap.

If the fixture is provided with a ground wire, connect the fixture ground wire to the outlet box ground wire with a wire connector after following the above steps. Never connect the ground wire to black or white power supply wires.

Make wire connections. Reference the chart below for correct connections and wire accordingly:

Tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor

Note : When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square-shaped or ridged, and the other wire will be round in shape or smooth (See illustration).
NOTE: The fixture should be installed with sockets [J] facing UP. Push the fixture to the wall, carefully aligning the mounting screws protruding from the mounting strap with holes in the canopy. NOTE: Make sure all wires are inside the canopy and do not get pinched between the mounting strap and canopy or wall and canopy of the fixture.

• Slip lock washers [B] over threads protruding through holes in the canopy (2 places).
• Screw knobs [A] onto threads protruding through holes in the canopy (2 places) and tighten to secure the fixture to the wall.
• Carefully slip the small opening in the glass shade [I] over the socket [J]. Make sure the glass shade base is fully seated on socket base [K].
• While holding the glass shade on the socket base, secure the glass shade by screwing the socket ring [F] onto the threads of the socket until snug against the inside surface of the glass shade. DO NOT OVER-TIGHTEN.
• Repeat steps 8 and 9 for the remaining glass shades.
• Insert recommended bulb(s) (not included).

REV 4-AUG-2023
For warranty information, please visit: kichler.com/warranty

FAQ

• Q: Where can I find the warranty information for the product?
  A: The warranty information can be found at kichler.com/warranty.

• Q: What should I do if I have additional questions or need assistance?
  A: For additional assistance, please contact our customer support at 866-558-5706 during our operating hours: Monday to Friday, 9am to 5pm EST.

FIXTURE DIAGRAM

PARTS LIST

• [A] Knob (2)
• [B] Lock Washer (2)
• [C] Strap Mounting Screw (2)
• [D] Mounting Strap
• [E] Mounting Screw (2)
• [F] Socket Ring
• [G] Outlet Box (not supplied)
• [H] Canopy
• [I] Glass Shade
• [J] Socket
• [K] Socket Base

CAUTIONS
CAUTION – RISK OF SHOCK:
Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

WARNING:

1. This fixture is intended for installation by the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING

• Always be certain that the electric current is turned off before cleaning.
• Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

INSTALLATION INSTRUCTIONS

1. Remove lock-up knobs[A] and lock washers[B] from mounting screws[E]. Retain knobs and lock washers.

2. Attach the mounting strap[D] to the outlet box[G] using the strap mounting screws[C]. Mounting strap can be adjusted to suit the position of the fixture.

3. Grounding instructions: (See Illus. a or b).
   a. On fixtures where the mounting strap is provided with a hole and two raised dimples, wrap ground wire from the outlet box around the green ground screw, and thread into the hole.
   b. On fixtures where a cupped washer is provided, attach the ground wire from the outlet box under the cupped washer and green ground screw, and thread it into the mounting strap.
   If the fixture is provided with ground wire, connect the fixture ground wire to the outlet box ground wire with a wire connector after following the above steps. Never connect ground wire to black or white power supply wires.

4. Make wire connections. Reference the chart below for correct connections and wire accordingly. *Note: When parallel wire (SPT 1 & SPT 2) is used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)

5. NOTE: Fixture should be installed with sockets[J] facing UP.
   Push the fixture to the wall, carefully aligning the mounting screws protruding from the mounting strap with holes in the canopy.
   NOTE: Make sure all wires are inside the canopy and do not get pinched between the mounting strap and canopy or wall and canopy of the fixture.

6. Slip lock washers[B] over threads protruding through holes in the canopy (2 places).

7. Screw knobs[A] onto threads protruding through holes in the canopy (2 places) and tighten to secure the fixture to the wall.

8. Carefully slip a small opening in glass shade[I] over the socket[J]. Make sure the glass shade base is fully seated on the socket base[K].

9. While holding the glass shade on the socket base, secure the glass shade by screwing the socket ring[F] onto threads of the socket until snug against the inside surface of the glass shade. DO NOT OVER-TIGHTEN.

10. Repeat steps 8 and 9 for the remaining glass shades.

11. Insert recommended bulb(s) (not included).

We’re here to help
866-558-5706 Hrs: M-F 9am to 5pm EST
For warranty information please visit: kichler.com/warranty

References

• Kichler® Warranty Information | Kichler Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>