infineon S6SATU01A I2C Interface for PMIC Communication Tool Installation Guide

S6SATU01A I2C Interface for PMIC Communication Tool

Please note that Cypress is an Infineon Technologies Company.
The document following this cover page is marked as “Cypress” document as this is the company that originally developed the product. Please note that Infineon will continue to offer the product to new and existing customers as part of the Infineon product portfolio.
Continuity of document content
The fact that Infineon offers the following product as part of the Infineon product portfolio does not lead to any changes to this document. Future revisions will occur when appropriate, and any changes will be set out on the document history page.
Continuity of ordering part numbers
Infineon continues to support existing part numbers. Please continue to use the ordering part numbers listed in the datasheet for ordering.

THIS SPEC IS OBSOLETE
Spec No: 002-08680
Spec Title: S6SATU01A I2C INTERFACE FOR PMIC
COMMUNICATION TOOL OPERATION GUIDE
Replaced by: NONE

© Cypress Semiconductor Corporation, 2014-2022. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC (“Cypress”). This document, including any software or firmware included or referenced in this document (“Software”), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, nonexclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress’s patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited.

TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypre does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the device or system could cause personal injury, death, or property damage (“Unintended Uses”). A critical component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.

Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of the

Preface

This manual explains how to use the evaluation board. Be sure to read this manual before using the product.
For this product, please consult with sales representatives or support representatives.

Handling and use
Handling and use of this product and notes regarding its safe use are described in the manuals.
Follow the instructions in the manuals to use this product.
Keep this manual at hand so that you can refer to it anytime during use of this product.

Notice on this document
All information included in this document is current as of the date it is issued. Such information is subject to change without any prior notice.
Please confirm the latest relevant information with the sales representatives.

Cautions

Caution of the products described in this document
The following precautions apply to the product described in this manual.

WARNING| Indicates a potentially hazardous situation which could result in death or serious injury and/or a
fault in the user’s system if the product is not used correctly.
---|---
Electric shock,
Damage| Before performing any operation described in this manual, turn off all the power supplies to the system.
Performing such an operation with the power on may cause an electric shock or device fault.
---|---
Electric shock,
Damage| Once the product has been turned on, do not touch any metal part of it.
Doing so may cause an electric shock or device fault.
CAUTION| Indicates the presence of a hazard that may cause a minor or moderate injury, damages to this product or devices  connected to it, or may cause to lose software resources and other properties such as data, if the device is not used appropriately.
---|---
Cuts, Damage| Before moving the product, be sure to turn off all the power supplies and unplug the cables. Watch your step when  carrying the product. Do not use the product in an unstable location such as a place exposed to strong vibration or a  sloping surface. Doing so may cause the product to fall, resulting in an injury or fault.
---|---
Cuts| The product contains sharp edges that are left unavoidably exposed, such as jumper plugs.
Handle the product with due care not to get injured with such pointed parts.
Damage| Do not place anything on the product or expose the product to physical shocks. Do not carry the product after the  power has been turned on.
Doing so may cause a malfunction due to overloading or shock.
Damage| Since the product contains many electronic components, keep it away from direct sunlight, high temperature, and  high humidity to prevent condensation. Do not use or store the product where it is exposed to much dust or a strong  magnetic or electric field for an extended period of time.
Inappropriate operating or storage environments may cause a fault.
Damage| Use the product within the ranges given in the specifications.
Operation over the specified ranges may cause a fault.
Damage| To prevent electrostatic breakdown, do not let your finger or other object come into contact with the metal parts of  any of the connectors. Before handling the product, touch a metal object (such as a door knob) to discharge any static electricity from your body.

Description

The S6SATU01A is communication tool for 2ch Buck + 1ch Buck/Boost DC/DC, S6SAP412A and for 3ch Buck + 1ch Buck/Boost DC/DC, S6SAP413A. This board implements our MCU : FM3(MB9AF312K) and can communicate with I2 C  easily by using windows PC and prepared software. It can select the output voltage, soft-start time, ON/OFF sequence, PFM/PWM mode.

Pin Descriptions

2.1 Input/output pin descriptions
Table 2-1. Input/output Pin Descriptions

MCU

| GND| –| Ground terminal
VBUS| O| VBUS terminal
USB_VCC| I| USB_VCC terminal
I2CVCC| I| Power supply terminal for I2C.
SCL_S| I| I2C clock terminal
SDA_S| I/O| I2C data I/O terminal
P10| I/O| MCU I/O port (25pin)
JP110| –| GND through JP110
P11| I/O| MCU I/O port (26pin)
JP111| –| GND through JP111
P12| I/O| MCU I/O port (27pin)
JP112| –| GND through JP112
P13| I/O| MCU I/O port (28pin)
JP114| –| GND through JP114
P14| I/O| MCU I/O port (29pin)
P15| I/O| MCU I/O port (30pin)
JP115| –| GND through JP115
P21| I/O| MCU I/O port (36pin)
P22| I/O| MCU I/O port (35pin)
P23| I/O| MCU I/O port (34pin)

2.2 Jumper, Switch descriptions
Figure 2-1. Jumper, Switch Descriptions

2 : VBUS pin
3 :USB_VCC pin
4 :I2CVCC pin
5 : SCL_S pin 6 : SDA_S pin 7 : P10 pin
9 : MCU P11 pin
11 : MCU P12 pin
13 : MCU P13 pin
15 : MCU P14 pin
16 : MCU P15 pin
18 : MCU P21 pin
19 : MCU P22 pin
20 : MCU P23 pin| –
CN105| Test terminal| –

Setup and Verification

3.1 Contents in a Package

[Using items for evaluation with I2C control]

• S6SATU01A
• USB cable
• PC installed Windows7 or later OS
• S6SAP412A or S6SAP413A

3.2 Evaluation with I2 C control
Any setting of S6SAP412A/S6SAP413A can be evaluated with Windows PC connected to USB port by I2 C communication GUI.

3.2.1 PC Setup

1. Unpack the driver file to a folder of PC running Windows 7 or later version OS, and run install.bat file.

2. Connect S6SATU01A to PC using USB cable.

3. After installed a device, open the device manager and confirm the new COM port.
   Start menu → Control panel → Device manager

4. Run “S6AP412A_413A_I2C.exe”

5. Click “PORT SEARCH” at “COM PORT SELECT” field and select “SIL Virtual Communications Port (COMxx) ”

6. Please unplug the USB cable after setup.

3.2.2 Operation check

1. Connect the S6SATU01A and S6SAP412A/S6SAP413A.

2. 3.3V is applied to VIN terminal of S6SAP412A/S6SAP413A.

3. USB cable is connected.

4. Run I2 C communication software and click the box of ON/OFF field.
   

5. Vo1, Vo2, Vo3 or Vo4 are output by software settings Figure 3-1. For I2C control evaluation
   

3.2.3 How to use I2 C communication GUI

Component and Wiring Layout

4.1 Component layout
Figure 4-1. Component Layout (Layer 1)

Figure 4-2. Component Layout (Layer 2)

4.2 Wiring layout
Figure 4-3. Wiring Layout (Layer 1)

Figure 4-4. Wiring Layout (Layer 2)

Circuit Schematic

Figure 5-1. Circuit Schematic

Component List

Table 6-1. Component List

No.| Component| Item| Parts number| Vendor| Value|

Remarks

---|---|---|---|---|---|---
1| IC101| MCU| MB9AF312K| Cypress| –| –
2| IC102| –| –| –| –| NMT
3| IC103| PMIC| TCR5SB33| TOSHIBA| –| –
4| IC104| –| –| –| –| NMT
5| Q101| Tr| BC857BLT1G| ROHM| –| PNP
6| X101| –| –| –| –| NMT
7| X102| Crystal| CX1255GB04000 H0PESZ1| KYOCERA| 4MHz| –
8| LED101| LED| OSHR1608C1A| OptoSupply| –| RED
9| SW101| Push-SW| SKHRAHA010| ALPS| –| –
10| C101| Ceramic Capacitor| C1608JB1H106M| TDK| 10µF| 50V
11| C109| Ceramic Capacitor| C1608JB1H106M| TDK| 10µF| 50V
12| C110| Ceramic Capacitor| C1608JB1H106M| TDK| 10µF| 50V
13| C102| –| –| –| –| NMT
14| C104| –| –| –| –| NMT
15| C105| –| –| –| –| NMT
16| C107| Ceramic Capacitor| C1608JB1V475K| TDK| 4.7µF| 35V
17| C103| Ceramic Capacitor| C1608JB1H104K| TDK|

0.1µF

| 50V
18| C105| –| –| –| –| NMT
19| C106| Ceramic Capacitor| C1608JB1H104K| TDK| 0.1µF| 50V
20| C108| Ceramic Capacitor| C1608JB1H104K| TDK| 0.1µF| 50V
21| C111| Ceramic Capacitor| C1608JB1H104K| TDK| 0.1µF| 50V
22| C114| Ceramic Capacitor| C1608JB1H104K| TDK| 0.1µF| 50V
23| C115| –| –| –| –| NMT
---|---|---|---|---|---|---
24| C116| Ceramic Capacitor| C1608JB1H104K| TDK| 0.1µF| 50V
25| C120| Ceramic Capacitor| C1608JB1H104K| TDK| 0.1µF| 50V
26| C112| Ceramic Capacitor| C1608C0G1H12 0J|

TDK

| 12pF| 50V
27| C113| Ceramic Capacitor| C1608C0G1H12 0J|

TDK

| 12pF| 50V
28| C118| –| –| –| –| NMT
29| C119| –| –| –| –| NMT
30| R137| Chip Resistor| RK73H1JTTD4R 70F| KOA| 4.7Ω|
31| R106| Chip Resistor| RR0816P-152-D| SUSUMU| 1.5kΩ|
32| R108| –| –| –| –| NMT
33| R109| –| –| –| –| NMT
34| R110| –| –| –| –| NMT
35| R117| –| –| –| –| NMT
36| R113| Chip Resistor| RR0816P-563-D| SUSUMU| 56kΩ|
37| R138| Chip Resistor| RR0816P-102-D| SUSUMU| 1kΩ|
38| R111| Chip Resistor| RR0816P-103-D| SUSUMU| 10kΩ| 1/16W, 0.5%
39| R112| Chip Resistor| RR0816P-103-D| SUSUMU| 10kΩ| 1/16W, 0.5%
40| R101| Chip Resistor| RR0816P-103-D| SUSUMU| 10kΩ| 1/16W, 0.5%
41| R104| Chip Resistor| RR0816P-103-D| SUSUMU| 10kΩ| 1/16W, 0.5%
42| R114| –| –| –| –| NMT
43| R115| –| –| –| –| NMT
44| R116| –| –| –| –| NMT
45| R123| Chip Resistor| RR0816P-202-D| SUSUMU| 2kΩ| 1/16W, 0.5%
46| R124| Chip Resistor| RR0816P-202-D| SUSUMU| 2kΩ| 1/16W, 0.5%
47| R125| Chip Resistor| RR0816P-202-D| SUSUMU| 2kΩ| 1/16W, 0.5%
48| R126| Chip Resistor| RR0816P-103-D| SUSUMU| 10kΩ| 1/16W, 0.5%
49| R127| –| –| –| –| NMT
50| R128| –| –| –| –| NMT
51| R129| –| –| –| –| NMT
52| R130| Chip Resistor| RR0816P-103-D| SUSUMU| 10kΩ| 1/16W, 0.5%
53| R131| Chip Resistor| RR0816P102D| SUSUMU| 1kΩ| 1/16W, 0.5%
54| R132| Chip Resistor| RR0816P-103-D| SUSUMU| 10kΩ| 1/16W, 0.5%
55| R133| Chip Resistor| RR0816P-220-D| SUSUMU| 22Ω| 1/16W, 0.5%
56| R134| Chip Resistor| RR0816P-220-D| SUSUMU| 22Ω| 1/16W, 0.5%
57| R135| –| –| –| –| NMT
58| R136| Chip Resistor| RR0816P-103-D| SUSUMU| 10kΩ| 1/16W, 0.5%
59| R137| –| –| –| –| NMT
60| R138| –| –| –| –| NMT
61| R139| Chip Resistor| RR0816P-103-D| SUSUMU| 10kΩ| 1/16W, 0.5%
62| R140| Chip Resistor| RR0816P-103-D| SUSUMU| 10kΩ| 1/16W, 0.5%
---|---|---|---|---|---|---
63| R141| Chip Resistor| RR0816P-103-D| SUSUMU| 10kΩ| 1/16W, 0.5%
64| R102| Chip Resistor| RR0816P-202-D| SUSUMU| 2kΩ| 1/16W, 0.5%
65| R103| –| –| –| –| NMT
66| R105| Chip Resistor| RR0816P-222-D| SUSUMU| 2.2kΩ| 1/16W, 0.5%
67| R118| –| –| –| –| NMT
68| R119| –| –| –| –| NMT
69| R120| –| –| –| –| NMT
70| R121| –| –| –| –| NMT
71| R122| –| –| –| –| NMT
72| CN101| Connector| UX60SC-MB-5ST| HIROSE| –| mini USB
73| CN102| –| –| –| –| NMT
74| CN103| –| –| –| –| NMT
75| CN104| Connector| 90122-0770| MOLEX| –| 2×10 L-angle pin header

76

|

CN105

|

Connector

|

90122-0770

|

MOLEX

|

–

| 2×10 L-angle pin header, Cut 90122-0770
77| JP110| JMP| JPPAD| –| –| Pattern Short
78| JP111| JMP| JPPAD| –| –| Pattern Short
79| JP112| JMP| JPPAD| –| –| Pattern Short
80| JP114| JMP| JPPAD| –| –| Pattern Short
81| JP115| JMP| JPPAD| –| –| Pattern Short
82| JP116| JMP| JPPAD| –| –| Pattern Short
83| JP117| JMP| JPPAD| –| –| Pattern Short
84| JP101| Solder JMP| JPPAD| –| –| Solder Short
85| JP102| Solder JMP| JPPAD| –| –| Solder Short
86| JP108| JMP| JPPAD| –| –| Pattern Short
87| JP131| –| –| –| –| NMT
88| JP132| JMP| JPPAD| –| –| Pattern Short
89| JP133| JMP| JPPAD| –| –| Pattern Short
90| JP104| Solder JMP| JPPAD| –| –| Solder Short
91| JP105| Solder JMP| JPPAD| –| –| Solder Short

Evaluation Board Picture

Figure 7-1. Picture (top)

Figure 7-2. Picture (back)

Ordering Information

Table 8-1. Ordering Information

Revision History

Document Revision History

Document Title: S6SATU01A I2 C Interface for PMIC Communication Tool Operation Guide
Document Number: 002-08680

Revision| Issue Date| Origin of
Change| Description of Change
---|---|---|---
*| 7/22/2014| MITK| Initial release.
A| 2/4/2016| MITK| Migrated Spansion Guide from S6SATUO1A_SS901-00027-1v0-E to Cypress format.
13| 11/30/2017| MASG| Updated Cypress new logo and copyright.
C| 8/22/2022| ATTS| Obsolete document. Completing Sunset Review.

S6SATU01A I2 C Interface for PMIC Communication Tool Operation Guide, Doc. No. 002-08680 Rev. *C

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>