Megatel Industrial Hardened Gigabit 95W POE Injector User Manual

June 7, 2024
Megatel

Megatel Industrial Hardened Gigabit 95W POE Injector User Manual

INJ-IG01-95W

This quick start guide describes how to install and use the Gigabit PoE Injector. The PoE Injector supports LTPoE++ 95W high power and it is a perfect choice for no power source of Ethernet environments.

Overview

INJ-IG01-95W is a Hardened PoE Injector which provides two 10/100/1000Base-TX ports and one port for PoE++ 95W PSE (Power Sourcing Equipment) and compliant with IEEE 802.3bt.

General

To ensure trouble free transportation and storage, all products must be thoroughly inspected, tested and properly packed before delivery. Check the product upon receipt for any visible damages which may have been caused during shipment.

Package Content

  • INJ-IG01-95W, Industrial 95W PoE Injector x 1 PCS
  • User Manual x 1 PCS

Physical Description

  • Front Panel
    Megatel Industrial Hardened Gigabit 95W POE Injector

  • Rear Panel
    Megatel Industrial Hardened Gigabit 95W POE Injector

Installation

DIN Rail Installation
This injector can be installed on a DIN rail. Installation steps are as follows:

  1. Tighten the screws to fix the DIN Rail plate

  2. Lock the upper part of the DIN rail clip on the upper side of the track. Press it until the metal part move downward and a “click sound is heard”.
    Inductions

Wall Mount Installation
It also can be installed on a Wall Mount. Installation steps are as follows:

  1. Tighten the screws to fix the DIN Rail plate
    Inductions

  2. Mount the switch on the wall or on a flat surface with 2 screws piercing through the mounting holes to secure it in position.

Setup

  1. Connect the Injector with the DC power supply. Ensure the power supply in connection with a power source and the PWR indicator is ON. If not, please ensure that the power cable is properly connected and the power supply is functioning normally.
  2. Connect the Ethernet Port to the network equipment (Switch or Hub), Connect the PoE Out Port to the Power Device (PoE IP-CAM).
  3. After all cables are correctly connected, the indicators will be lit as per port status LED Indicators.

Interface

RJ-45 Pin Assignment

Pin

| Signal Name
---|---

1

| TP0+ Positive (VCC+)

2

| TP0- Positive (VCC+)

3

| TP1+ Negative (VCC-)

4

| TP2+ Positive (VCC+)

5

| TP2- Positive (VCC+)

6

| TP1- Negative (VCC-)

7

| TP3+ Negative (VCC-)

8

| TP3- Negative (VCC-)

Power Connection

Pin/ Descriptio

|

V –

|

V +

|

---|---|---|---

Power Input

|

GND

|

+52~56VDC

Cable Connections

Signal Type Cable Type Connector
Ethernet Cat. 5 or above RJ45
Power supply Power cable 2-pin Terminal Block

LED Indicators

Indicator Color Status Description
PWR Green ON Powered ON

PoE

|

Green

| ON| PoE is activated.
Blinking| A Power Device (PD) is being detected.
OFF| No device is connected or the connected device is not a PD.

Dimensions of this Injector (Unit: mm)

injector

Functional Descriptions

  • 1 RJ45 Gigabit data input port to 1 RJ45 Gigabit PSE output port (Data + Power)
  • Support PoE++ (95W)
  •  Compatible IEEE802.3bt PoE++
  •  Support 10/100/1000Base-TX
  •  Extensive LED indicators for PoE diagnostics
  •  52~56VDC Terminal Block Power inputs
  •  Support DIN-Rail or Wall-mount installation
  •  -40°C to 75°C ( -40°F to 167°F) operating temperature range

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals