BARCO C3010S ClickShare Wireless Presentation Solution User Manual
- June 5, 2024
- BARCO
Table of Contents
C3010S ClickShare Wireless Presentation Solution
User Manual
Safety
About this chapter
Read this chapter attentively, it contains important information to prevent
personal injury while using ClickShare. It also includes several cautions to
prevent damage to the ClickShare product. Ensure that you understand and
follow all safety guidelines, safety instructions, and warnings in this
chapter before using your ClickShare.
Clarification of the term “C3010S” used in this document
When referring in this document to the term “C3010S” means that the content is
applicable for the following Barco products:
- CX-20
- CX-30
Model certification name C3010S
Covered ClickShare products
| Regional version | Contains | Accessories included |
|---|---|---|
| R9861612xxB11 | • R9861611 | |
| • 1 x R9861600D01C 2 | • DC adapter with AC clips type A, C, G, I |
• Printed safety manual
• Wall mount
R9861613xxB2 1
R9861600D01C 2| • R9861611
• 2 x R9861600D01C 2
1 x R9861600D01C 2| • DC adapter with AC clips type A, C, G, I
• Printed safety manual
• Wall mount
Contact your local sales representative for the correct regional variant necessary in your environment.
General safety
Safety warnings
The installation of the device must comply with the guidelines in the
ClickShare Installation Guide.
- Installation must be performed by qualified personnel only and must conform to all local codes.
- External power connections must be properly insulated.
- Do not connect directly to mains power for any reason.
- To prevent injuries and physical damage, always read this manual and all labels on the system before connecting to the wall outlet.
- The ClickShare product is intended to be used in office and indoor environments only.
- Only use the power adapter supplied with your device. While appearing to be similar, other power adapters have not been safety tested at the factory and may not be used to power the device. For a replacement power adapter, contact your dealer.
- This product is intended to be supplied by a UL Listed Power Unit marked “Class 2” or “LPS” or “Limited Power Source” input 100-240V, 50/60Hz 0.7A and with output rated 12 VDC 2A.
- Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect the cord, pull it out by the plug. Never pull the cord itself.
- If an extension cord is used with this product, make sure that the total of the Ampere ratings on the products plugged into the extension cord does not exceed the extension cord Ampere rating.
- Never spill liquid of any kind on the product. Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel before resuming operations.
- Lightning – For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC power-line surges.
- Only use attachments/accessories specified by the manufacturer.
Environment
Do not place this equipment on an unstable cart, stand, or table. The product
may fall, causing serious damage to it.
Risk of electric shock
Do not open. To reduce the risk of electric shock, do not remove the cover of
the unit or of the power supply unit. No user-serviceable parts inside. Refer
all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
- When the power cord or plug is damaged or frayed.
- If liquid has been spilled into the equipment.
- If the product has been exposed to rain or water.
If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions since improper adjustment of the other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.
- If the product has been dropped or the cabinet has been damaged.
- If the product exhibits a distinct change in performance, indicating a need for service.
- Replacement parts: When replacement parts are required, be sure the service technician has used original
Barco replacement parts or authorized replacement parts that have the same characteristics as the Barco original part. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock, or other hazards. Unauthorized substitutions may void the warranty.
- Safety check: Upon completion of any service or repairs to this device, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
Heat and Fire Hazard
Warning – the risk of fire: do not place flammable or combustible
materials near the device!
Barco products are designed and manufactured to meet the most stringent safety
regulations.
This device radiates heat on its external surfaces during normal operation,
which is both normal and safe.
Exposing flammable or combustible materials into close proximity of this
device could result in the spontaneous ignition of that material, resulting in
a fire. For this reason, it is absolutely necessary to leave an “exclusion
zone” around all external surfaces of the device where no flammable or
combustible materials are present. The exclusion zone must be not less than
40 cm (16”) for all Barco devices. Do not cover the device with any material
while it is in operation.
Mount the device in a well-ventilated area away from sources of ignition and
out of direct sunlight.
Slots and openings in this equipment are provided for ventilation. To ensure
the reliable operation of the device and to protect it from overheating, these
openings must not be blocked or covered. The openings should never be blocked
by placing the device too close to walls, or another similar surface. This
device should never be placed near or over a radiator or heat register. This
device should not be placed in a built-in installation or enclosure unless
proper ventilation is provided.
In the event of a fire, use sand, CO2, or dry powder fire extinguishers; never
use water on an electrical fire.
Fusing: Internal fuse for the Line is provided in the power supply. A blown
internal fuse is an indication of catastrophic failure of circuit
component(s). Repair must be performed by authorized personnel. Fuses must be
replaced with the same type and ratings.
Environmental Condition Check
Environment condition check
For installations in environments where the device is subject to excessive
dust, then it is highly advisable and desirable to have this dust removed
prior to it reaching the device’s clean air supply. Devices or structures to
extract or shield excessive dust well away from the device are a prerequisite;
if this is not a feasible solution then measures to relocate the device to a
clean air environment should be considered.
It is the client’s responsibility to ensure at all times that the device is
protected from the harmful effects of hostile airborne particles in the
environment of the device. The manufacturer reserves the right to refuse
repair if a device has been subject to negligence, abandonment, or improper
use.
Ambient temperature conditions
Max. ambient temperature: +40°C or 104°F at sea level, +35°C or 95°F at 3000m
Min. ambient temperature: 0°C or 32°F
Storage temperature: -10°C to +60°C (14°F to 140°F)
Humidity Conditions
Storage: 0 to 90% relative humidity, non-condensing
Operation: 0 to 85% relative humidity, non-condensing
Environment
The ClickShare product is intended to be used in office and indoor
environments only.
Do not install the device in a site near heat sources such as radiators or air
ducts, or in a place subject to direct sunlight, excessive dust, or humidity.
Be aware that room heat rises to the ceiling; check that temperature near the
installation site is not excessive.
Maximum allowed altitude to use the product: 3000m (9843Ft). Due to China
regulation, the maximum altitude is limited to 2000 meters (6561 feet) on
China’s mainland.
Compliance FCC
Federal Communication Commission Interference Statement
You are cautioned that changes or modifications not expressly approved by the
part responsible for compliance could void the user’s authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
You may also find helpful the following booklet, prepared by the FCC: “How to
Identify and Resolve Radio-TV Interference Problems.” This booklet is
available from the U.S. Government Printing Office, Washington D.C. 20402.
Changes and Modifications not expressly approved by the manufacturer or
registrant of this equipment can void your authority to operate this equipment
under Federal Communications Commissions rules.
In order to maintain compliance with FCC regulations shielded cables must be
used with this equipment.
Operation with non-approved equipment or unshielded cables is likely to result
in interference to radio & television reception.
This device complies with Part 15 of the FCC Rules. Operation is subject to
two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference
that may cause undesired operation.
FCC RF Radiation Exposure Statement: This device is capable of operating in
802.11a mode. For 802.11a devices operating in the frequency range of 5.15 –
5.25 GHz, they are restricted from indoor operations to reduce any potential
harmful interference for Mobile Satellite Services (MSS) in the US. WIFI
Access Points that are capable of allowing your device to operate in 802.11a
mode (5 .15 – 5.25 GHz band) are optimized for indoor use only. If your WIFI
network is capable of operating in this mode, please restrict your WIFI use
indoors to not violate federal regulations to protect Mobile Satellite
Services.
- This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20
cm between the radiator and your body.
Base Unit Contains FCC ID: PPQ-WCBN814A
Buttons FCC ID (model R9861600D01C): 2AAED-R9861600D01
Buttons FCC ID (model CSBTN004): 2AAED-CSBTN004
ClickShare Buttons 2AAED-R9861600D01 has been tested and meets the FCC RF
exposure guidelines. The maximum SAR value reported is 1.19 W/kg.
ClickShare Buttons 2AAED-CSBTN004 has been tested and meets the FCC RF
exposure guidelines. The maximum SAR value reported is 0.47 W/kg.
ClickShare Buttons 2AAED-R9861600D01 or 2AAED-CSBTN004 should be installed and
operated with a minimum distance of 5 mm between the radiator and your body.
FCC responsible: Barco Inc., 3059 Premiere Parkway Suite 400, 30097 Duluth GA,
United States, Tel: +1 678 475 8000
For country-code selection usage (WLAN devices) :
Note: The country code selection is for non-US models only and is not
available to all US models. Per FCC
regulation, all WiFi products marketed in the US must be fixed to US operation
channels only.
International Safety Standards
Standards overview
This equipment is built in accordance with the requirements of the
international safety standards IEC62368-1, EN62368-1, UL62368-1, and CAN/CSA
C22.2 No.62368-1, which are the safety standards of information technology
equipment including electrical business equipment. These safety standards
impose important requirements on the use of safety-critical components,
materials, and insulation, in order to protect the user or operator against
the risk of electric shock and energy hazards and having access to live parts.
Safety standards also impose limits on internal and external temperature
rises, radiation levels, mechanical stability and strength, enclosure
construction, and protection against the risk of fire. Simulated single fault
condition testing ensures the safety of the equipment to the user even when
the equipment’s normal operation fails.
Compliance IC
Canada, Industry Canada (IC) Notices
This device complies with Industry Canada licence-exempt RSS standard (s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Radio Frequency (RF) Exposure Information
The radiated output power of the Barco Wireless Device is below the Industry
Canada (IC) radio frequency exposure limits. The Barco Wireless Device should
be used in such a manner that the potential for human contact during normal
operation is minimized.
Caution: Exposure to Radio Frequency Radiation.
- To comply with the Canadian RF exposure compliance requirements, this device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
- To comply with RSS 102 RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons.
Base Unit Contains IC: 4491A-WCBN814A
Buttons IC (model R9861600D01C): 21559-R9861600D01
Buttons IC (model CSBTN004): 21559-CSBTN004
IC Antenna statement
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
This radio transmitter 4491A-WCBN814A has been approved by Industry Canada to
operate with the antenna types listed below with the maximum permissible gain
and required antenna impedance for each antenna type indicated. Antenna types
not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
Indoor use only warning
Operation in the band 5150-5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems.
Certification information (SAR)
This device is also designed to meet the requirements for exposure to radio
waves established by Industry Canada.
The SAR limit adopted by Canada is 1.6 W/kg averaged over one gram of tissue.
The highest SAR value reported to the IC for this device type complies with
this limit.
The highest SAR value reported to the IC for this device type when used in
portable exposure conditions is 1.15 W/kg.
International Type Approval
KCC certification
R-R-BVY-xxxxx
R-C-BVY-R9861600D01
Russian certificate
Mexican certificate
I FEEL ID: RCPBACxxx-xxxx
KCC Statement
KCC Statement
CE Certification
C3010S (R981605EU, R9861611EUB1, R9861612EUB1 and R9861613EUB2) are fit for
use in all European Union countries, EFTA and Turkey.
The C3010S is restricted to indoor use only when operating in the 5150 to 5250
Mhz frequency range.
Hereby, Barco NV declares that the radio equipment type C3010S is in
compliance with Directive 2014/53/
The full text of the EU declaration of conformity is available at the
following internet address:
www.barco.com/clickshare/ce/CE_R9861611.pdf
(Base Unit)
For 2.4 GHz band:
• 2402 MHz – 2482 MHz
• Max EIRP: 20 dBm| For 5 GHz band:
• 5150 MHz – 5350 MHz
• 5470 MHz – 5725 MHz
• Max EIRP: 23 dBm
---|---
www.barco.com/clickshare/ce/CE_R9861600D01C.pdf
(Buttons)
The ClickShare Buttons R9861600D01C has been tested and meets the EU RF
exposure standards. The maximum SAR value reported is 0.678 W/kg.
For 2.4 GHz band:
• 2402 MHz – 2482 MHz
• Max EIRP: 19.88 dBm| For 5 GHz band:
• 5150 MHz – 5350 MHz
• 5470 MHz – 5725 MHz
• Max EIRP: 20.28 dBm
---|---
www.barco.com/clickshare/ce/CE_CSBTN004.pdf
(Buttons)
The ClickShare Buttons CSBTN004 has been tested and meets the EU RF exposure
standards. The maximum SAR value reported is 0.164 W/kg.
For 2.4 GHz band:
• 2402 MHz – 2482 MHz
• Max EIRP: xx.xx dBm| For 5 GHz band:
• 5150 MHz – 5350 MHz
• 5470 MHz – 5725 MHz
• Max EIRP: xx.xx dBm
---|---
UK Compliance
C3010S (R981605EU, R9861611EUB1, R9861612EUB1 and R9861613EUB2) is fit for use
in the UK.
The C3010S is restricted to indoor use only when operating in the 5150 to 5350
Mhz frequency range.
Hereby, Barco NV declares that the radio equipment type C3010S is in
compliance with the Radio Equipment Regulations 2017: Great Britain. The full
text of the UK declaration of conformity is available at the following
internet address:
www.barco.com/clickshare/uk/UKCA_R9861611.pdf
(Base Unit)
For 2.4 GHz band:
• 2402 MHz – 2482 MHz
• Max EIRP: 20 dBm| For 5 GHz band:
• 5150 MHz – 5350 MHz
• 5470 MHz – 5725 MHz
• Max EIRP: 23 dBm
---|---
www.barco.com/clickshare/uk/UKCA_R9861600D01C.pdf (Buttons)
For 2.4 GHz band:
• 2402 MHz – 2482 MHz
• Max EIRP: 19.88 dBm| For 5 GHz band:
• 5150 MHz – 5350 MHz
• 5470 MHz – 5725 MHz
• Max EIRP: 20.28 dBm
---|---
www.barco.com/clickshare/uk/UKCA_CSBTN004.pdf (Buttons)
For 2.4 GHz band:
• 2402 MHz – 2482 MHz
• Max EIRP: xx.xx dBm| For 5 GHz band:
• 5150 MHz – 5350 MHz
• 5470 MHz – 5725 MHz
• Max EIRP: xx.xx dBm
---|---
Authorized Representative:| Barco UK Ltd
---|---
Address:| Building 329, Doncastle Road
Bracknell RG12 8PE, Berkshire, United Kingdom
Importer:| • Midwich Limited, Vinces Road, Diss, Norfolk, IP22 4YT UK
• TD Maverick UK, Redwood 2, Crockford Lane, Chineham Business Park
Basingstoke RG24 8WQ UK
Battery Information
European Union
Batteries, battery packs, and accumulators should not be disposed of as
unsorted household waste.
Please use the public collection system to return, recycle, or treat them in
compliance with the local regulations.
Avoid:
- high or low extreme temperatures that a battery can be subjected to during use, storage or transportation; and low air pressure at high altitude.
- leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
- a battery subjected to the extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
Taiwan
For better environmental protection, waste batteries should be collected
separately for recycling or special disposal.
California, USA
The button cell battery may contain perchlorate material and requires special
handling when recycled or disposed of in California.
For further information please visit:
https://www.dtsc.ca.gov/hazardouswaste/perchlorate/
References
- Anatel — Agência Nacional de Telecomunicações
- Inspired sight and sharing solutions - Barco
- Inspired sight and sharing solutions - Barco
- Support - Barco
- dtsc.ca.gov/hazardouswaste/perchlorate/
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>