infans BE10006 Pack and Play Baby Bedside Sleeper User Manual

infans BE10006 Pack and Play Baby Bedside Sleeper

Specifications

• Brand : Baby Playard
• Model : BE10006
• Includes : Bassinet, Mattress, Mattress support bars, Adjustable plastic connectors, Long rail lock button, Bottom fixed buckles, Legs, Short rail lock button, Wheels, Music and toys, Diaper changing table, Storage rack, Carry bag, Anchor plate and strap, Rocking bar

Product Usage Instructions

Assembly Instructions

How to set up the bassinet

WARNING: Please follow the instructions step by step. Do not push down the center bottom base until all top bars are locked and rigid.

1. Remove the product from the carry bag and undo the Velcro straps of the mattress.
2. While keeping the bassinet bottom base high, pull up the short bars in a quick upward motion to lock them into place. Note: There are two unlocking mechanisms on each bar, please try to pull it quickly and avoid grabbing the center unlocking mechanisms.
3. While keeping the bassinet bottom base high, pull up the long bars in a quick upward motion to lock into place. Note: If a top bar does not lock into place, pull the base higher and try again.
4. After the four top bars are locked and rigid, reach through the access hole on the sleeping nest bottom and gently push down the bottom base until it is locked.
5. Zip up the second sleeping layer, and install six mattress support bars into fabric tunnels on the second sleeping layer.
6. Lay the mattress on the second sleeping layer. If a gap is visible on either side of the mattress after installation, reposition the mattress. There is Velcro behind the mattress and a second sleeping layer that can be used to fix the mattress.
7. Insert two holding bars and connect two locker bars with holding bars.

How to use the rocking bar

1. Fix the plastic grip with the bottom tube. Rock the bars from the left and right sides.
2. When the rocking bar is pushed inside the way, the rocking function stops.
3. Connect the locker bars on the bassinet bars and push down to lock. Assemble straps as shown and adjust the length according to the baby’s size.

Operating Instructions

How to use as Co-sleeping bassinet 3-position height adjustment

Find the RED locking button 1 under the plastic connectors on the left and right sides. Press button 1 then pull up button 2 of both sides at the same time, then push down the top rail to a lower position. Note: The left and right side plastic connector pieces must be slid down at the same time for smooth lowering of the top rail.

When set to the lowest position, pull out buckles of mattress support straps from the pockets. Pull the strap up and over the lowering rail and connect to the front of the lowering rail. Note: The strap is only for the lowest position security.

Assemble the buckle as shown in the picture and adjust the length of the strap according to the size of the adult bed.

FAQ

• Q: How do I clean the Baby Playard BE10006?
  • A : Use a damp cloth with mild soap to wipe down surfaces. Allow to air dry completely before reassembling.
• Q: Can I use this product outdoors?
  • A : It is recommended for indoor use only to ensure safety and stability.

Parts List

Assembly instructions

How to set up the bassinet

WARNING : Please follow the instructions step by step. Do not push down the center bottom base until all top bars are locked and rigid.

STEP 1: Remove the product from the carry bag and undo the Velcro straps of the mattress.

STEP 2 : While keeping the bassinet bottom base high, pull up the short bars in a quick upward motion to lock into place.
Note : There are two unlocking mechanisms on each bar, please try to pull it quickly and avoid grabbing the center-unlocking mechanisms.

STEP 3 : While keeping the bassinet bottom base high, pull up the long bars in a quick upward motion to lock them into place.
STEP 4 : After the four top bars are locked and rigid, reach through the access hole on the sleeping nest bottom and gently push down the bottom base until it is locked.
STEP 5: Zip up the second sleeping layer, and install six mattress support bars into fabric tunnels on the second sleeping layer.
Note : If a top bar does not lock into place, pull the base higher and try again.

STEP 6 : Lay the mattress on the second sleeping layer. If a gap is visible on either side of the mattress after installation, reposition the mattress. There is Velcro behind the mattress and a second sleeping layer that can be used to fix the mattress.
STEP 7:
01: Insert two holding bars.
02: Connect two locker bars with holding bars.

How to use the rocking bar

STEP 8: Fix the plastic grip with the bottom tube, see pictures 1 and 2.

01 : Rocking the bars from the left and right sides.
02 : When the rocking bar is pushed inside way, the rocking function stops.

How to use the rocking bar

03 : Connect the locker bars on the bassinet bars and push down to lock. Please make sure that the buckle is installed when the baby is lying on the changing table.
Assemble the straps as shown, and adjust the length of the straps according to the size of the baby.

STEP 9 :

• Attach the shelf to the side of the long or short armrest position you like.
• Assemble five parts as a picture and place them on the bassinet.

WARNING

Possible entanglement or strangulation injury. Keep out of the baby’s reach. Remove the toy when the baby begins to push up on their hands and knees. Recommended use from birth to 5 months.
This toy is not intended to be “mouthed” by the baby and should be positioned clearly out of reach of the baby’s face and mouth. On cribs with adjustable mattress levels, the highest position may allow the toy to be too close to the baby. The second or lower position is more appropriate.
The drop side of the crib should never be lowered with the toy in place and the baby left unattended.
Always attach all provided fasteners (strings, straps, clamps, etc.) tightly to a crib or playpen according to the instructions. Check frequently. Do not add additional strings or straps to attach to a crib or playpen.

Operating Instructions

How to use as Co-sleeping bassinet
3-position height adjustment

Find the RED locking button 1 under the plastic connectors on the left and right sides, press the button 1 then pull up button 2 of the both sides at the same time, then push down the top rail to the lower position.
Note : The left and right side plastic connector pieces must be slid down at the same time so that the top rail can be lowered smoothly.

When set to the lowest position, you can pull out buckles of mattress support straps from the pockets. Pull the strap up and over the lowering rail and connect on the front of the lowering rail.

NOTE : The strap is only for lowest position security.

Assemble the buckle as shown in the picture and adjust the length of the strap according to the size of the adult bed.

WARNING

The attachment system must ALWAYS be used in bedside sleeper mode.

• ACCEPTABLE ADULT BED CONDITIONS FOR Co SL EEPING MODE (BEDFRAME IN-LINE)
• UNACCEPTABLE ADULT BED CONDITIONS FOR Co-SLEEPING MODE (BEDFRAME NOT IN-LINE)

Not suitable for use next to water beds or children’s beds.

How to use as Baby Playard

Take out the mattress, remove the mattress support bar and the second sleeping layer, and then place the mattress on the bottom layer.

How to fold the bassinet

STEP 1: Remove mattress support bars and mattress, and set aside. Reach through the hole of the sleeping nest floor to the red release strap, and pull up to collapse the bassinet.

STEP 2: Unlock the short top rails by raising the center base slightly, pushing on the button of rail locks 1 and lower top rails. Repeat the steps on top rails on the long sides.

STEP 3: Lift up the bassinet and adjust the corner posts together until the corner posts are straight up and down, and top corner brackets contact each other.

STEP 4: Wrap the mattress around the unit. There are Velcro straps that feed through plastic loops attached to the backside of the mattress. Pull taut.

STEP 5 :

• Put it into the carry bag.
• do as shown

WARNING

Failure to follow these warnings and instructions could result in serious injury or death.
Read all instructions before assembling and using the product.

SUFFOCATI ON HAZARD

Discard all packing materials immediately after opening. Plastic bags and ties may cause suffocation or choking.

Infants have suffocated

• In gaps between extra padding and the side of the bassinet, and
• On soft bedding
• Use only the pad provided by the manufacturer. NEVER add a pillow, comforter, or another mattress for padding.
• The side rails can only be lowered when the bassinet in bedside sleeper mode. Please keep the side rails on top position while in the bassinet and play yard mode.

WARNING

HORIZONTAL RAIL is installed in the uppermost position unless securely attached to the adult bed. Always check to be sure that the upper locking bars and the lower locking bars are in their “locked position” before placing the infant in the bedside bassinet.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep unless otherwise advised by their physician.

FALL HAZARD -Always check that the bassinet is securely locked on the base/stand pulling upwards on the bassinet bed.

Do not place any cord, strap or similar item in or near this accessory that could become wrapped around a child’s neck.

If a sheet is used with the pad, use only the one provided by the bassinet or cradle manufacturer or one specifically designed to fit the dimensions of the bassinet or cradle mattress.

• WARNING This beside sleeper is designed for use only with adult beds that are between 19 and 24 inches from floor to top of the adult mattress.
• WARNING To avoid death from the infant’s neck being caught on the top rail on the side that is next to the adult bed, the top rail must be no higher than the adult bed mattress.
• FALL HAZARD -To help prevent falls, do not use this product when the infant begins to push up on hands and knees or has reached the manufacturer’s recommended maximum weight of 19.8 lbs (9kg), whichever comes first. Strings can cause strangulation! Do not place items with a string around a child’s neck, such as hood strings or pacifier cords. Do not suspend strings over a bassinet or cradle, or attach strings to toys.
• WARNING
  Entrapment Hazard- To prevent death from entrapment, beside sleeper must be properly secured to the adult bed using the attachment system.

1. There must be no more than 0.5 in.(13mm) gap between beside sleeper and adult bed.
2. Check tightness before each use by pulling beside the sleeper in a direction away from the adult bed.
3. If the gap exceeds 0.5 in.(13mm), DO NOT use the product. Do not fill the gap with pillows, blankets or other items that are suffocation hazards.

• WARNING
  • Always use ALL required parts for each use mode. Check the instruction manual for a list of required parts. Periodically check the product for loose, damaged or missing parts.
• WARNING
  • Always read and follow assembly instructions for each product use mode (bedside sleeper, bassinet, playard).
• WARNING
  • DO NOT use a bedside sleeper if any parts are missing, damaged, or broken. Contact the manufacturer for replacement parts and instructional literature if needed. DO NOT substitute parts.
• WARNING
  • Keep instructions for future use.
• WARNING
  • Assemble the product according to the manufacturer’s instructions for ANY use mode-bedside sleeper as well as the bassinet or play yard modes, or both.
• WARNING
  • A bedside sleeper is designed to provide a sleeping area for an infant until he or she begins to push up on hands and knees or at approximately 5 months of age. Move your child to another sleeping product when your child reaches this stage.

WARNING

A WARNING-NEVER LEAVE INFANT IN PRODUCT WITH SIDES DOWN.

The infant may roll into space between the pad and the loose mesh side causing suffocation.

Failure to follow these warnings and instructions could result in serious injury or death. The product, including side rails, must be fully erected prior to use. Strings can cause strangulation! Never place items with a string around a child’s neck such as hood strings or pacifier cords. Never suspend strings over products or attach strings to toys. Discontinue use of the product when the child can climb out or reach the height of 35 in.(890mm). Children can become entrapped and die when improvised netting or covers are placed on top of the product. Never add such items to confine the child
in the product. When the child is able to pull to a standing position, remove bumper pads, large toys, and other objects that could serve as steps for climbing out. Never place the product near a window where cords from blinds or drapes can strangle a child. Use ONLY the mattress/pad provided by the manufacturer (which must be at least 46in. long by 22.8in. wide and not more than 0.59in.thick). Always provide the supervision necessary for the continued safety of your child. When used for playing, never leave the child unattended. To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back to sleep, unless otherwise advised by your physician.

• WARNING

  • Never leave the child in the product with the side lowered, be sure the side is in a raised and locked position whenever a child is in the product.
  • Never use plastic shipping bags or other plastic film as mattress covers are not sold and are intended for that purpose. They can cause suffocation.
  • Never use a water mattress with this product.

• WARNING

  • FALL HAZARD: Children have suffered serious injuries after falling from changing tables. Falls can happen quickly.

• STAY in arm’s reach of your child.

• ALWAYS secure this product to the support frame (manufacturer’s instructions for securing the changing table accessory).

• SUFFOCATION HAZARD: Babies have suffocated while sleeping in changing areas. Changing areas are not designed for safe sleeping.

• NEVER allow the baby to sleep in the changing area.
  Do not use a changing table for a child who has reached the height of 22in. (558mm), weight of 15lbs. (6.8kg) or 3 months old, whichever comes first.

• WARNING

  • Never use this product if there are any loose or missing fasteners, loose joints, broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact us for replacement parts. Never substitute parts.

• WARNING

  • A statement describing the hazard. Never leave the changing table in place when a child is in a non-full-size crib/play yard. A statement describing the hazard. Never leave the second layer in place when the child is in a non-full-size crib/play yard. Read all instructions before using the changing table. Do not use the changing table if it is damaged or broken.

Care & Cleaning

Spot clean with a soft clean damp cloth. Toy bar and music box: Wipe clean with a damp cloth and mild soap. Air dry. Don’t immerse in water.
Dolls : Hand wash, air dry.
Frame : Wipe the metal frame with a soft, clean cloth and mild soap.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>