SW-MOTECH HTA.18.768.10001 Legend Gear Side Carrier SLC Instruction Manual
- June 16, 2024
- SW-MOTECH
Table of Contents
mounting instructions
BC.HTA.18.768.20000 * contains
HTA.18.768.10001
HTA.18.768.11001
BC.HTA.00.402.10100L
BC.HTA.00.401.10100R
Mounting instructions
Revision: 00 – Datum / Date: 02-2017
Art.-Nr. / tem No.: HTA.18.768.10001 & HTA.18.768.11001
Legend Gear Side Carrier SLC
Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application
charts and PDF mounting instructions, Any other documents that may be required
(e.g. ABE certifications), are also available for download at our webshop.
Installation and / or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and / or servicing carried out by a specialist workshop!
SW-MOTECH assumes no liability for damage caused by improper installation and
/ or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver!
These mounting instructions are written based on our current state of
knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts [e.g. the chain) are in the original state of
maintenance.
Installed accessories can change the driving behaviour and / or stability of
your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration
/operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority.
PREPARATION: Read the mounting instructions carefully and make sure that
all items of the parts list are included. Make sure that your vehicle is
parked safely and cannot fall over. Turn off the engine and remove the
ignition key. Let the motor / exhaust cool off if necessary. Disconnect the
vehicle battery when working on the electrical system, Use appropriate tools,
Have another person to help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturers’ specifications or
replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise
specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTECH must be obtained from the
vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and
connections previously removed are properly replaced. Also make sure that no
moving parts are obstructed and no function of the vehicle is hindered in any
way. Cables and hoses must not rub and / or be pinched. Before starting to
ride, perform a comprehensive check of all functions. After the first 50 km
and then at regular intervals, check the tightening torque of all screw
connections and the proper fit of the product.
Packed by:………………………………..
Date of packaging:……………………….
SW-MOTECH GmbH & Co. KG
Ernteweg 8/10
35282 Rauschenberg
Germany
Tel. / phone + 49 (0]6425 / 8168 – 050
Fax / fax + 49 (0)6425 / 8168 – 10
info@sw-motech.com
www.sw-motech.com
Step| No| Item No. / Description| Part| Quantity**|
**Nm
---|---|---|---|---|---
| | HTA.18.768.10001| Legend Gear Side Carrier SLC left| |
1| 1| HTA.18.768.901.02| Side Carrier (left side)| 1/1|
2| -HTA.00.152.080| Guide Bolt| 3/3|
3| _HTA00,152,081| Lock Bolt| 1/1|
4| “M6 x 20; DIN 6912| Hexagon Socket Screw, short head| 1/1| 7
5| M6 x 20; DIN 7991| Countersunk Screw; black| 2/2| 7
3| 6| UNC %” x 3%”| Hexagon Socket Screw with Inch Thread| 1/1|
7| “4-13; DIN 125| Washer| 1/1|
8| “UNC Sa” x 3”| Hexagon Socket Screw with Inch Thread| 1/1|
9| Ø 20/085/h10| Spacer| 1/1|
10| Ø 15/084/h5| Spacer| 1/1|
| | “HTA.18.768.11001| Legend Gear Side Carrier SLC Right| |
1| 1| “HTA.18.768.902.02| Side Carrier (right side]| 1/1|
2| HTA,00,152,080| Guide Bolt| 3/3|
3| -HTA.00.152.081| Lock Bolt| 1/1|
4| M6 x 20; DIN 6912| Hexagon Socket Screw, short head| 1/1| 7
5| M6 x 20; DIN 7991| Countersunk Screw; black| 2/2| 7
3| 6| UNC 4″ x 3%”| Hexagon Socket Screw with Inch Thread| 1/1|
7| d 13; DIN 125| Washer| 1/1|
8| UNC Su” x 3| Hexagon Socket Screw with Inch Thread| 1/1|
9| Ø 20/08,5/h10| Spacer| 1/1|
10| Ø 15/08,4/h5| Spacer| 1/1|
- All measurements In millimeters. – ** The second number indicates the total quantity of the part in the delivery.
*** No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
MOUNTING
NOTE: This mounting step shows the mounting on the left side carrier.
Repeat the same procedure on the right side with the parts of the right side
carrier.
Attach the parts (2) to (5) to the side carrier [1], as shown in the drawing.
ATTENTION: Use liquid thread locker!
Tighten the screws as specified in the parts list.
NOTE: The mounting steps [2] and [3] show the mounting of the left side
carrier to the vehicle. Repeat the same procedure on the right side with the
parts of the right side carrier.
ATTENTION: Before starting the mounting, unload the spring struts with a
suitable jack, as shown in the detail drawing!
Remove the original screws from the spring strut and vehicle frame.
ATTENTION: Pay attention to the vehicle-specific or spring-leg-spe- cific
assignment of the mounting parts [shown in the detail drawings).
Attach the side carrier (1] to the vehicle, as shown in the drawing. Use the
original nut (Orig.).
ATTENTION: Use liquid thread locker!
Tighten the screws with the manufacturer’s specified torque.
MOUNTING INSTRUCTIONS
Legend Gear Side Bag LC1 / LC2
– Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application
charts and PDF mounting instructions. Any other documents that may be required
le.g. ABE certifications), are also available for download at our webshop. >>
www.sw-motech.com
Carefully follow all the directions given in the mounting instructions. Also
pay attention to all relevant information in the vehicle manual during
assembly. Nonconformance can lead to vehicle damage or even endanger the
driver! Please keep the mounting instructions as reference. SW-MOTECH assumes
no liability for damages caused by improper fixation and handling.
This product was developed for vehicles in their original condition.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Installed accessories can change driving behaviour
and/or stability of your vehicle,
GENERAL INFORMATION
Please observe any country-specific regulations concerning vehicle
registration,
PREPARATION: Read the mounting instructions carefully and make sure that all
parts are included. Make sure that your vehicle is parked safely and cannot
fall over. Turn off the engine and remove the ignition key. Let the
motor/exhaust cool off if necessary. Make sure to use only the appropriate
tools. During installation have another person help you.
FUNCTION CHECK: This is a universal product. For this reason make sure
BEFORE the first use, that the product can be fixed properly and used without
problems with your vehicle type.
ATTENTION: All components of the product must not contact any hot or
moving parts of the vehicle. All parts should also remain 5 cm away from hot
parts of the vehicle and remain clear of the exhaust stream. After mounting,
make sure there are no clearance issues while the suspension is both
compressed and extended.
ATTENTION: Before riding and at each stop (every 200 km) check proper
fixation of the product!
After fixation also make sure that no moving parts are obstructed and the
function of the vehicle is not hindered in any way, Lamps as taillight and
turn signals must not be limited in their function. Cables and hoses must not
rub and/or be pinched. Before starting to ride, perform a comprehensive check
of all functions.
LOADING INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving
and braking performance! Make sure weight is evenly distributed!
ATTENTION: Depending on the location of fixation, cornering and ground
clearance can be reduced by using this product!
Never store pointy or sharp-edged objects in the product, which could cause
injury to persons or damage to the vehicle/product.
Use a waterproof inner bag/raincover to protect your luggage from moisture,
Additionally protect sensitive luggage [e.g., electronic equipment) from
moisture with a plastic bag.
ATTENTION: Maximum load: 5 kg / 11 lbs! The maximum vehicle load
specified by the manufacturer must not be exceeded!
ATTENTION: Maximum speed with this product: 130 km/h!
SW-MOTECH GmbH & Co. KG
Ernteweg 8/10 – 35282 Rauschenberg – Germany
Tel. / phone + 49 (0)6425 / 8168 – 050
Fax / fax + 49 (0)6425 / 8168 – 10
info@sw-motech.com –
www.sw=motech.com
PARTS LIST & CARF
CARE
Clean the product periodically or after each trip, as dust and dirt have a
wear-effect and permanent stains can be prevented. Clean the product after
riding in salty conditions, to avoid damage from salt.
First remove dust and encrustations with a soft dry brush. Remove stubborn
deposits with a soft cloth and warm soapy water. Do NOT use strong cleaning
agents, rough cleaning tools or high pressure washer! Then rinse with clear
water,
Before re-use dry the product for at least 24 hours in the air [not in direct
sunlight).
We recommend to impregnate the cotton textile surface of the product in
regular intervals or after intensive cleaning with a commercial wax
impregnation (e.g. from Fjallraven).
ATTENTION: Because the textile surfaces material is a natural fiber, it
will experience color changes or fading when exposed to direct sunlight for
extended periods of time and by environmental factors [e.g., SMOG, acid rain,
etc.)! SW-MOTECH assumes no Liability for this!
ATTENTION: Dirt on the product and vehicle has an abrasive effect and can
damage surfaces, such as the paint. Make sure that all areas of the vehicle,
which have contact with the product or parts of the product as straps, are
protected with an adhesive protection film from scratches and abrasions.
SW-MOTECH assumes no liability for paint damage and abrasions.
FIXATION
Fasten the Velcro closure of the side bag [1a/1b).
Revert the reinforced opening of the side bag [1a/1b) twice completely.
Fix the shown loops with the side-mounted hook buckles,
Tighten the straps of the hook buckle.
Secure the opening of the side bag (1a/1b) with the shown strap.
Place the three openings of the quick release fastening system onto the locating bolts of the mounted SLC side carrier,
Press the side bag [1a/1b] slightly downward, until it properly rests on SLC
side carrier.
ATTENTION: Make sure that all three locating bolts engage at the same
time!
Pay attention to the clearly audible snap sound of the locking mechanism!
To release the side bag [1a/1b) simply press the shown slider of the locking mechanism downward.
Errors and omissions excepted. Technical and design modifications are subject to change.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>