scandomestic WAH 3110 W Washing Machine User Manual

scandomestic WAH 3110 W Washing Machine User Manual

Safety Instructions

Warning!
Use all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the operation instructions handy for later use. If the application is sold or passed on then ensure that the new owner always receives those operation instructions.

Safety Instructions
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury or loss of life. Explanation of the symbols:

Warning!
This combination of symbol and signal word indicates a potentially dangerous situation which may result in death or serious injuries unless it is avoided.

Caution!
This combination of symbol and signal word indicates a potentially dangerous situation which may result in slight or minor injuries or damage to property and the environment.

Note!
This combination of symbol and signal word indicates a potentially dangerous situation which may result in slight or minor injuries.

Electric shock hazzard

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• The new hose-sets supplied with the appliance are to be used and that old hose-sets should not be reused.
• Before any maintenance the device, unplug the appliance from the mains.
• Always unplug the machine and turn off the water supply after use. The max. inlet water pressure, in pascals. The min. inlet water pressure, in pascals.
• To ensure your safety, power plug must be inserted into an earthed three-pole socket. Check carefully and make sure that your socket is properly and reliably earthed.
• Make sure that the water and electrical devices must be connected by a qualified technician in accordance with the manufacturer’s instructions and local safety regulations.

Risk to children!

• EN countries: the appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Children of less than 3years should be supervised to ensure that they do not play with appliance.
• Animals and children may climb into the machine. Check the machine before every operation.
• Kids should be supervised that they do not play with the appliance.
• Glass door may be very hot during the operation. Keep kids and pets far away from the machine during the operation very wet rooms as well as in the rooms with explosive or caustic gas.
• Remove all packages and transport bolts before using the appliance. Otherwise, serious damage may result.
• Plug must be accessible after installation.

Risk of explosion!

• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances( such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.) This may result in fire or explosion.
• Before hand thoroughly rinse items of washing by hand.
• Installing the product!
• This washing machine is for indoor use only.
• It isn’t intended to be built-in using.
• The openings must not be obstructed by a carpet.
• Washing machine shall not be installed in bath room or very wet rooms as well as in the rooms with explosive or caustic gases.
• The washing machine with single inlet valve only can be connected to the cold water supply. The product with double inlet valves should be correctly connected to the hot water and cold water supply.
• Plug must be accessible after installation.
• Remove all packages and transport bolts before using the appliance. Otherwise, serious damage  may result.

Risk of damaging appliance!

• Your product is only for home use and is only designed for the textiles suitable for machine washing.
• Do not climb up and sit on top cover of the machine.
• Do not lean against machine door.
• Cautions during Handling Machine:
  1. Transport bolts shall be reinstalled to the machine by a specialized person.
  2. The accumulated water shall be drained out of the machine.
  3. Handle the machine carefully. Never hold each protruded part on the machine while lifting. Machine door can not be used as the handle during the conveyance.
  4. This appliance is heavy. Transport with care.
• Please do not close the door with excessive forces. If it is found difficult to close the door, please check if the clothes are put in or distributed well.
• It is forbidden to wash carpets.

Operating the appliance!

• Before washing the clothes at first time, the product shall be operated in one round of the whole procedures without the clothes inside.
• Flammable and explosive or toxic solvents are forbidden. Gasoline and alcohol etc. Shall not be used as detergents. Please only select the detergents suitable for machine washing, especially for drum.
• Make sure that all pockets are emptied. Sharp and rigid items such as coin, brooch, nail, screw or stone etc. may cause serious damages to this machine.
• Please check whether the water inside the drum has been drained before opening its door. Please do not open the door if there is any water visible.
• Be careful of burning when the product drains hot washing water.
• Never refill the water by hand during washing.
• After the program is completed, Please wait for two minutes to open the door.

Packaging/Old appliance

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the collection systems or contact the retailer where the product was purchased. They return and can take this product for environmental safe recycling.

Warning!
This appliance is intended to be used in household.

Installation

Before installing the machine, the location characterized as follows shall be selected:

Installation area
Stability is important to prevent the product from wandering!

• Make sure that the product should not stand on the power cord.
• Rigid, dry, and level surface
• Avoid direct sunlight
• Sufficient ventilation
• Room temperature is above 0℃
• Keep far away from the heat resources such as coal or gas.
• Minimum 20 mm space from walls to appliance

Unpacking the washing machine

Warning!
Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk of suffocation! Keep all packaging well away from
children.

1. Remove the cardboard box and styrofoam packing.
2. Lift the washing machine and remove the base packing. Make sure the small triangle foam is removed with the bottom one together. If not, lay the unit down with side surface, then remove the small foam from the unit bottom manually.
3. Remove the tape securing the power supply cord and drain hose.
4. Remove the inlet hose from the drum.

Remove transport bolts

Warning!
You must remove the transport bolts from the backside before using the product. You will need the transport bolts again if you move the product, so make sure you keep them in a safe place.

Please take the following steps to remove the bolts:

1. Loosen 4 bolts with spanner and then remove them.
2. Stop the holes with transport hole plugs.
3. Keep the transport bolts properly for future use.

Levelling the washing machine

Warning!
The lock nuts on all four feet must be screwed tightly against the housing.

• Check if the legs are closely attached to the cabinet. If not, please turn them to their original positions tighten the nuts.
• Loosen the lock nut turn the feet until it closely contacts with the floor.
• Adjust the legs and lock them with a spanner, make sure the machine is steady.

Connect Water Supply Hose

Warning!

• To prevent leakage or water damage, follow the instructions in this chapter!
• Do not kink, crush, modify or sever water inlet hose.
• For the model equips hot valve, connect it to hot water tap with hot water supply hose. Energy consumption will decrease automatically for some program.

1. Connection between water supply and inlet hose.
   

2. Connect the other end of inlet pipe to the inlet valve at the backside of product and fasten the pipe tightly clockwise.

Drain Hose

Warning!

• Do not kink or protract the drain hose.
• Position drain hose properly, otherwise damage might result of water leakage.

There are two ways to place the end of drain hose:

1. Put it into the water trough.

2. Connect it to the branch drain pipe of the trough.
   

Note!
If the machine has drain hose support, please install it like the following.

Warning!

• When installing drain hose, fix it properly.
• If drain hose is too long, do not force it into washing machine as it will cause abnormal noises.

Before Each Washing

• The working condition of the washer should be (0-40)℃. If used under 0℃, the inlet valve and draining system may be damaged. If the machine is placed under condition of 0℃ or less, then it should be transferred to normal ambient temperature to ensure the water supply hose and drain hose are not frozen before use.
• Please check the labels and the explanation of using detergent before wash. Use non-foaming or less-foaming detergent suitable for machine washing properly.

Check before each wash

• Check the label
• Put small clothes into the pillow slip
• Take out the items out of the pockets
• Turn easy-pilling and long-pile fabric inside out
• Knot the long strips,zip or button
• Separate clothes with different textures

Warning!
When washing a single clothes, it may easily cause great eccentricity and give alarm due to great unbalance. Therefore it is suggested to add one or two more clothes to be washed together so that draining can be done smoothly.
Don’t washing the clothes touching with kerosene, gasoline, alcohol and other flammable materials.

Detergent Dispenser

Pre Wash detergent
II Main Wash detergent

• Softener

Caution!
Detergent only need to be added in “case I “after selecting pre-washing for machines with this function.

X = means must
O = means optional

Note!
As for the agglomerated or ropy detergent or additive, before they are poured into the detergent box, it is suggested to use some water for dilution to prevent the inlet of detergent box from being blocked and overflowing while filling water.

Please choose suitable type of detergent for the various washing temperature to get the best washing performance with less water and energy consumption.

Cleaning And Care

Warning: Before your maintenance starts, please unplug the machine and close the tap. Cleaning The Cabinet Proper maintenance on the washing machine can extend its working life.  The surface can be cleaned with diluted non- abrasive neutral detergents when necessary. If there is any water overflow, use the wet cloth to wipe it off immediately. No sharp items are allowed.

Note: Formic acid and its diluted solvents or equivalent are forbidden, such as alcohol, solvents or chemical products, etc.

Cleaning The Drum
The rusts left inside the drum by the metal articles shall be removed immediately with chlorine-free detergents. Never use steel wool.

Note: Don’t put laundry in the washing machine during the drum cleaning.

Cleaning The Door Seal And Glass

Wipe the glass and seal after each wash to remove lint and stains. If lint builds up it can cause leaks.
Remove any coins, buttons and other objects from the seal after each wash.

Cleaning The Inlet Filter

Note: Inlet filter must be cleaned if there is less water.

Washing the filter in the tap

1. Close the water supply
2. Remove the water supply hose from the tap.
3. Use an old tooth brush or similar small brush to clean the filter.
4. Reconnect the water supply hose.

Washing the filter in washing machine:

1. Screw off the inlet pipe from the backside of the machine.
2. Pull out the filter with long nose pliers and reinstall it back after being washed.
3. Use an old tooth brush or similar small brush to clean the filter.
4. Reconnect the inlet pipe.
   Note: It is possible to pull out the filter and wash it separately.

Clean The Detergent Dispenser

Press down the arrow location on softener cover inside the dispenser drawer. Lift the clip up and take out softener cover and wash all grooves with water.
Restore the softener cover and push the drawer into position.

1. Pull out the dispenser drawer with press the A

2. Clean the dispenser drawer under water

3. Clean inside the recess with an old toothbrush

4. Insert the dispenser drawer

Note!
Do not use alcohol, solvents or chemical products to clean the machine.

Cleaning The Drain Pump Filter

Warning: Be careful of the hot water!

• Allow detergent solution to cool down.
• Unplug the machine to avoid electrical shock before washing.
• Drain pump filter can filter the yarns and small foreign matters from the washing.
• Clean the filter periodically to ensure the normal operation of washing machine.

Open the lower cover cap

Rotate 90°C and pull out the emergency drain hose, and take off the hose cap

After water runs out,reset the drain hose

Open the filter by turning to the counter clockwise

Remove extraneous matter

Close the lower cover cap

Caution!

• Make sure that valve cap and emergency drain hose are reinstalled properly, cap plates should be inserted aligning to hole plates otherwise water may leak.
• Some machines don’t have emergency drain hose, so step 2 and step 3 can be skipped. Rotate lower cover cap directly to make water run into basin.
• When the appliance is in use and depending on the programme selected there can be hot water in the pump. Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty. When replacing the cover, ensure it is securely re-tightened.

Trouble Shooting

The start of the appliance does not work or it stops during operation. First try to find a solution to the problem, If not, contact the service centre

the door is closedCheck if the clothes is stuck
Door can opened| not be| Washer safety pro- tection design is working| Disconnect the power, restart the product
Water leakage| The connection be- tween inletpipe or outlet hose is not tight| Check and water pipesClean up hose| fasten
outlet
Detergent in the box| residue| Detergent is damp- ened or agglomer- ated| Clean and wipe de- tergent
Indicator or display does not light| Disconnect the powerPC board or harness has connection problem| Check if the power is shut down and the power plug is connected cor- rectly
Abnormal noise| | Check if the fixing (bolts) have been removed Check it’s installed on a solid and level floor

Error codes:

clothes is stuck
E10| Water injecting prob- lem while washing| Check if the water pres- sure is too lowStraighten the water pipeCheck if the inlet valve filter is blocked
E21| Overtime water drain- ing| Check if the drain hose is blocked
E12| Water overflow| Restart tehe washer
EXX| Other| Please try again first, call up the service line if there are still troubles.

Technical Specifications

Model ………………………………………………………………………….. WAH 3110
Washing capacity ……………………………………………………………….. 10.0 kg
Dimension (HxWxD mm)…………………………………… 850 x 595 x 565 mm
Net Weight…………………………………………………………………………… 72 kg
Rated power………………………………………………………………………. 1950W
Power Supply ……………………………………………………….. 220-240V~,50Hz
MAX.Current ………………………………………………………………………….. 10A
Standard Water presure…………………………………………..0.05MPa~1MPa

Product Description

A Water supply hose
B Detergent dispenser
C Door
D Top cover
E Control panel
F Power supply cord
E Drum
H Service filter
I Drain hose

Note: The product line chart is for reference only, please refer to real product as standard.

Accessories

• Transport hole plugs
• Supply hose cold water
• Supply hose warm water (optional)
• rain hose support (optional)
• User manual

Control Panel

1. Note: The chart is for reference only, Please refer to real product as
   standard.

2. On/Off
   Product is switched On/Off.

3. 2 Start/Pause
   Press the button to start or pause the washing cycle.

4. Option
   This allows you to select an additional function and will light when selected.

5. Programmes
   Available according to the laundry type.

6. Display
   The display shows the settings, estimated time remaining, options, and status messages for your washer. The display will remain on through the cycle.

Display

A Remain
B Delay
C Speed Wash
D My Cycle
E Extra Rinse
F Pre Wash
G Mute Buzzer
H Reload
I Child Lock
J Door Lock
K Spin Speed
L Temp.
M Rate Of Progress(Pre Wash- Wash -Rinse-Spin)
N Wash Time: 1,25, Delay Time: 2h, Error: E20, End: end

Operation

Delay
Set the Delay function:

1. Select a programme;
2. Press the Delay button to choose the time (the delaying time is 0- 24 H.);
3. Press [Start/Pause] to commence the delay operation Choose the Programme > Setting time >Start

Cancel the Delay function:
Press the [Delay] button until the display be 0H. It should be pressed before starting the programme. If the programme already started, should switch off programme to reset a new one. Caution: If there is any break in the power supply while the machine is operating, a special memory stores the selected programme and when the power is restarted, the program will continue.

Pre Wash
The Prewash function can get an extra wash before main wash, it is suitable for washing the dust rises to surface of the clothes; You need to put detergent into the Case (I) when select it.

Extra Rinse
The laundry will undergo extra rinse once after you select it.

Speed Wash
The function can decrease the washing time.

My Cycle
To memory the frequently used programme.  After choosing the programme and setting the options, press [Speed Wash] 3 sec. before start to wash. The default setting course is Cotton.

Reload
This operation can be executed during the washing progress. When the
drum is still rolling and there is large amount of water with high temperature in the drum. The state is unsafe and the door cannot be opened forcefully. To press [Start/Pause]3 sec. to reload, and start the clothes adding in the midway function. Please follow the steps as bellow:

1. Wait until the drum stops rotation.
2. The door lock is unlocked.
3. Close the door when the clothes are reloaded and press the [Start/Pause] button.

Press [Start/Pause] 3sec. > Reload the clothes > Start
Caution: Don’t use the Reload function when the water level over the edge of the inner tub or the temperature is higher.

Other Functions

Temp.
Press the button to regulate the temperature (Cold, 20℃, 30℃, 40℃, 60℃, 90℃) Spin
Press the button to change the speed. 1400: 0-600-800-1000-1200-1400 1500: 0-600-800-1000-1200-1500

Child Lock
To avoid mis operation by children. Press [Extra Rinse] and [Pre Wash] 3 sec. till buzzer beep.

Caution: When child lock is activated and program starts, child lock indicator will switch on, and the CL and remaining time on the display are alternately displayed in 0.5s. Press the other buttons will make child lock indicator flash for 3s. when program finish,CL and END alternate for 10s in 0.5s, then the child lock lights flash for 3s

Only press and hold the two button can release child lock, even power off, switch off and program end
The “Child Lock” will lock all buttons except Power button and Child Lock button
Please release child lock before selecting program and staring washing

Mute the buzzer
Press the [Temp.]and [Spin] for 3sec., the buzzer is mute. To act the buzzer function, press the button again for 3 seconds. The setting will be kept until the next reset.

Caution: After Muting the buzzer function, the sounds will not be activated any more.

ProgrammeS

Programmes are available according to the laundry type.

Cotton| Hard-wearing textiles, heat-resistant textiles made of cotton or linen.
Synthetic| Wash synthetic articles, for example: shirts, coats, blending.While washing the knitting textiles, detergent quantity shall be reduced due to its loose string construction and easily forming bub- bles.
Sterilization| Keep the washing temperature above 60 de- grees for more than30 minutes, effectively remove harmful bacte- ria.
Jeans| Specially for jeans.
Mix| Mixed load consisting of textiles made of cot- ton and synthetics.
20°C| 20°C default, can choose cold water.
Rinse&Spin| Extra rinse with spin.
Intensive| To increase the washing effects, washing time is increased.
ECO 40-60| This program is specially designed for washing duvet coats. Default 40°, not selectable, suitabale for laun- dry washing at about 40°-60°C.
Delicate| For delicate, washable textiles, e.g. made of silk, satin, synthetic fibres or blended fabrics.
Sport Wear| Washing the activewear.
Rapid 45’| This programme is suitable for washing not very dirty clothes, save more energy and washing.
Quick 15| Extra short programme approx, suitable for lightly soiled

Washing Programmes Table

Concerning to Regulation(EU) No 1061/2010, The EU energy efficiency class is: A+++
Energy test program: Intensive 60/40 ℃; Speed: The highest speed; Other as the default.
Half load for 7/8/9/10/12Kg machine: 3,5/4/4,5/5/6Kg.
Concerning to Regulation (EU) 2019/2023, The EU energy efficiency class  is: B
Energy test program: ECO 40-60. Other as the default.
Half load for 7/8/9/10/12Kg machine: 3,5/4/4,5/5/6Kg.
Quarter load for 7/8/9/10/12Kg machine: 2/2/2,5/2,5/3,5Kg.

Note: The parameters in this table are only for user’s reference. The actual parameters maybe different with the parameters in above mentioned tabl

References

• Scandomestic | scandomestic.dk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>