scandomestic EMV 104 Cooker Hoods User Manual
- October 30, 2023
- scandomestic
Table of Contents
scandomestic EMV 104 Cooker Hoods
Product Information
The product is a household cooker hood that comes with two methods of ventilation – horizontal and vertical. It has an energy-efficient lighting system and a motor that operates at low, medium, and high speeds. The product has metal filters that can be cleaned and changed. It is made of different types of plastics, including PE, PS, PO M, PP, and AB S. The product has an annual energy consumption of 30.6 kWh/a and a sound power level of 68 dB.
Product Usage Instructions
Installation
There are two methods for ventilation – horizontal and vertical. Please pay attention to the ventilation method when installing. For horizontal ventilation, use the cover to seal the outlet on the top, and for vertical ventilation, use the cover to seal the outlet on the back. Turn the adjuster to either an outdoor or indoor position for air ventilation accordingly. Method A involves using screws to tighten the hood to the cupboard, while Method B involves putting a one-way valve on the cooker hood.
Operation
The switch is operated as below: Press 0 to turn off the motor. Press the button to low, middle, and high to turn on the motor at low, medium, and high speeds respectively. Press light to turn on and off the lighting system.
Maintenance
To change or clean the metal filters, please do not use any corrosive detergent and unplug them before cleaning. To change the light bulb, refer to the product data sheet for more information.
Warning
- Children should be supervised to ensure that they do not play with the appliance.
- This appliance is designed for domestic use only.
- Any installation work must be carried out by a qualified electrician or competent person
- There is a fire risk if cleaning is not carried out in accordance with the instructions. Details concerning the method and frequency of cleaning are stated in the section “INSTALLATION AND MAINTENANCE”.
- Do not pull on the connection cord, but rather on the plug, to separate the appliance from the mains
- When cleaning an appliance, it must be off the power first.
INSTALLATION AND MAINTENANCE
Method A
- The cooker hoods should be placed at a distance of 500-650mm from the cooking surface for best effect.Electricity = Min. 500 mm. Gas Min. 650 mm.
- To install onto the wall, drill 4 holes of 08mm on a suit- able place according with the centre distance of hole in the back of the cooker hood.
- Insert the nut into the holes.
- Insert the screws into the nuts and tight.
- Put up the cooker hood onto the fixed screws.
- Then use the attached ac- accessories enclosed to turn the screws into the two holes inside the hood, and then fix the screws to tighten the hood onto the wall.
- Put the one-way valve onto the cooker hood.
Method B
- Drill 6 holes of 04mm at the bottom of the hanging cupboard.
- Put the one way valve on the cooker hood, then install the cooker hood on the bottom of the cupboard, tighten the hood with enclosed 6 screws.
- Install the adjusted board on the bottom of the hood in order to keep out the gap between hood back and cupboard.
Notice
- There are 2 methods for ventilation, including horizontal ventilation and ver-tical ventilation. Please pay attention to the ventilation method when installation.
- Horizontal ventilation: As pic.A shown, please use the cover to seal the outlet on the top, then the air can be vented from the back.
- Vertical ventilation: As pic B shown, please use the cover to seal the outlet on the back, then the air can be vented from top.
Air ventilation setting
Outdoor air ventilation: Turn the adjuster to outdoor position (pic.5A),
install the outlet, turn on the cooker hood, then the air will be vented from
the outside outlet. Indoor air ventilation: Turn the adjuster to indoor
position (pic.5B), install the outlet cover, turn on the cooker hood, then the
air can be vented from the inside outlet.
Operation:
The switch is operated as below:
- Press “0”, the motor will be off.
- Press the button to “low”, “middle” and “high”, the motor will be turned on at “low”, “middle” and “high” speed respectively.
- Press “light”, the light will be on. Press it again, the light will be off.
Maintenance
Changing and cleaning the filter. The methods are as below:
- Put the filter into the water of 40-50°C,Put some deter-gent in, and leave it for 2-3 minutes. Then use the soft brush to clean it with proper strength, in order not to damage the filter.
- 2 The filter can be cleaned by dish washer. Put the filter into the dish washer and put some detergent in, then turn the temperature to 60°C.
All the filters are made of metal. Please do not use any corrosive detergent
when cleaning.
Notice: Please unplug before cleaning.
Changing the light bulb
- Before changing the lights, make sure that the appliance is plugged off.
- Open the filter , see be- side picture.
- Change the Max. 2W LED by electrician
- Replace the filter to the original position.
Product data sheet
For household cooker hoods accordingly to regulation (EU). No. 65/2014 and 66/2014
| Symbol | Value | Unit | |
|---|---|---|---|
| Model | EMV 104 |
EMV 105
| |
Annual Energy Consumption| AEChood| 30,6| kWh/a
Time increase factor| f| 1,7|
Fluid Dynamic Efficiency| FDEhood| 8,8|
Energy Efficiency Index| EEIhood| 72,3|
Measured airflow rate at the best efficiency| QBEP| 74,4| m3/h
Measured air pressure at best efficiency point| PBEP| 201| Pa
Maximum airflow| Qmax| 138,1| m3/h
Measured electric power input at best efficiency point| WBEP| 47| W
Nominal power of the lighting system| WL| 2| W
Average illumination of the lighting system on the cooking surface| Emiddle|
74| lux
Measured power consumption on standby mode| PS| —| W
Measured power consumption on off mode| PO| —| W
Sound power level| LWA| 68| dB
- Scandomestic A/S
- Thrigesvej 2
- DK-8600 Silkeborg
- T + 45 7242 5571
- F + 45 8622 5571
- scandomestic.dk.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>