scandomestic OFC 191 E Impulse Cooler User Manual

June 4, 2024
scandomestic

scandomestic logo OFC 191 E/OFC 222 E
OFC 231 E/OFC 381 E
User manual

Thank you for choosing and purchasing our product.
Please carefully read the operation instructions before use for a correct application and satisfactory effect.

General

This product is a type of chilling cabinet, which is our new development of refrigeration combining the advanced technologies from both and abroad on the basis of food cabinet standards and corporate criteria. Its main kits and key components are all good brands, either and with streamlined design, the product integrates the actual market demand in structural design, which better caters to the ergonomics requirements of consumers. This series applies mainly to displaying and selling drinks, dairy products, vegetables, and fruits.

Structure and Parts

scandomestic OFC 191 E Impulse Cooler -

Handle and Erection

Handle with care
Unplug the wall socket first. Never tilt it over 45 degrees during handling.| Dry place
Always locates the refrigerator in a dry place.
---|---
|
Sufficient space
The distance from both sides and back of the refrigerator to the wall or other substance must not be less than 10cm. The refrigeration capability might be decreased if its surrounding space is too small to circulate air.| Well, ventilation
Always locates the refrigerator in a place with fine ventilation. For the first time use, wait for 2 hours after handling and then plug the wall socket and start it.
|
Far from a heat source
Never place the refrigerator directly under the sunshine. Never locate it nearby any heat source or heater to prevent it from reducing refrigeration capability.| No heavy load
Never put any heavy load on the top of the refrigerator.
|
No hole making
Never make a hole in the refrigerator. Never install other matter on the refrigerator.| Stable location
Unpacking and locating the refrigerator in a flat and solid place.
|

Preparation and Power Supply

Exclusive power socket
Normally, the power supply should be 187-242V, 50Hz single phase AC with exclusive single phase three pin receptacle (250V, 10A) and fuse (6A). The power receptacle must have a reliable earth connection.| No share on socket
Never let the refrigerator share the common socket with other appliances, otherwise, the cable becomes hot and fire might result
---|---
|
Protect cables
Never break or damage the cables otherwise current leakage and fire might result.| No water flushing
Never give the refrigerator surface a flush otherwise current leakage might result.
|
Prevent flammables and explosive
Never put any flammable or explosive inside the refrigerator such as ether, gasoline, alcohol, adhesive or explosive. Never put dangerous products nearby the refrigerator.| No spray
Spraying the flammables such as paint or coating nearby the refrigerator is not allowed, otherwise, a fire might result.
|
After power break
After a power break or unplugging the refrigerator, always wait at least 5 minutes and then you may plug the refrigerator and start it again.| No medicine
No medicine is allowed to keep inside the refrigerator.
|

Use and Caution

  1. Before use: Plug the refrigerator into 230V~ exclusive socket. After the refrigerator runs, put your hand on the air suction to confirm it is sufficiently cold. Then you may put food inside the cold box.
  2. Digital Temperature controller:

Features Of Function

  • It is a mini-sized and integrated intelligent controller and applicable to the compressor of one Hp.
  • The main functions are: Temperature Display/ Temperature control/Manual, automatic defrost by burning off/Illumination Control/Value Storing/self Testing/parameter Locking.

Front Panel Operation

  1. Set temperature
    Press button and the set temperature is displayed.
    Press or buttons to modify and store the displayed value, and
    Press the button to exit the adjustment and display the cold-room temperature.

  2. If no more button is pressed within 10 seconds, the cold-room temperature will be displayed.

  3. Illumination: Presabufton, it lights; Press  again, and it stops. Manual start/stop defrost:
    Press the button and hold for 6 seconds to defrost or stop defrosting.

  4. Refrigerant LED: During refrigeration,the LED is on; When the cold room temp.is constant, the LED is off; During the delay start, the LED flashes.

  5. Defrost LED: during defrosting, the LED is on; When it stops defrosting, the LED is off, During the delayed display of defrosting, the LED flashes.

  6. Digital controller reset
    When the display shows “Disorder”, press the ” ” button for 2s until the buzzer rings and quickly press the ” ” button for 6s until the buzzer rings again, the display will flash for 3s and it restores the factory setting.

Maintenance

  1. Cabinet cleaning. The product should be cleaned once a week with the power supply disconnected. In cleaning please use mild rinsing water or non-corrosive cleanser essence. Do not wash it directly with a water faucet.
  2. De-dusting for the condenser. The condenser should be cleaned every Three months with the power supply disconnected. Clean the condenser, at the bottom panel for air suction, and remove the dust on the cooling fin of the condenser with a wire brush or high-pressure air gun.
  3. Leaking check. Observe all connectors and welding joints for oil stains, which indicates a must for patching measures or call for professionals.
  4. Frequently observe the operation of the product. Lu case of any abnormal noise, smell, or smog, cut off the power supply immediately and call for professionals for help. Do not restart the product before trouble is cleared.
  5. We will not be responsible for any accident incurred by the failure of following the notices.

Trouble Shooting

Number Troubles Causes Solutions
1 Strange noise under the bottom shelf The fan blade broke. Power off and

fix the blade.
2| Non-refrigerating in spite of the normal operation| 1. Unit off.
2. Melting process
3. Refrigerant leaking
4. Unit failure.| 1. Power on.
2. Stop melting.
3. Patch the leak and refill refrigerant
4. Call for professionals.
3| Weak air from air curtain, and higher cabinet temperature| 1. Evaporator blocked by frost.
2. Inside fan is damaged.
3. Too low set point of temperature controller.
4. Vent blocked by storage| I increase the melting frequency.
2. Replace the fan.
3. Adjust the set point.
4. Remove the storage.
4| Normal air curtain, but higher cabinet temperature| lInsufficient refrigerant.
2. Too high a set point of temperature controllers.
3. The wind curtain is disturbed by strong airflow. 4. Ambient temperature or humidity beyond standards.| 1. Refill the refrigerant.
2. Adjust the set point for the temperature controller.
3. Removing the disturbing factors.
4. Improve the conditions.
5| Melting water overflown| 1. Heating pipe for melting water damaged 2 .Water-level controller failure.
3. Ambient temperature or humidity beyond standards.| 1. Replace the heating pipe.
2. Replace the water-level controller.
3. Improve the conditions.
6| Normal air curtain, but Periodical fluctuation of cabinet temperature| 1. Condenser contaminated.
2. Poor venting of the unit.
3. Heat protection from compressor failure
4. Capillary is blocked by ice
5. Temperature controller failure.| 1. Clean the condenser.
2. Improve the venting conditions.
3. Replace the heat protection.
4. Replace the drying filter.
5. Replace the temperature controller

Note
The following phenomena are not trouble: The murmur of water is heard when the refrigerator is working. It is a normal phenomenon as the coolant is circulating in the system. In the wet season, condensation might be found on the outside of the refrigerator. It is not a trouble, which is caused by high humidity. Simply use a cloth to wipe it.

Principle of Refriger action system

The principle of compression refrigeration consists of “compression”, “condensation”, “throttling”and”vaporization”. The compression is undertaken by the compressor, the condensation is completed by the condenser, The throttling is executed by the capillary, and the vaporization is implemented by the evaporator. When the coolant is circulating in the closed refrigeration system, the compressor sucks coolant, which absorbs heat in the evaporator, and the coolant becomes a high-pressure and high-temperature gas. In the condenser, it dissipates heat in the air, while the coolant is reliquefied and throttled in the capillary and then enters into the evaporator with low pressure. the liquefied coolant quickly boils and vaporizes into gas when the pressure suddenly drops. Meanwhile, it absorbs heat inside the refrigerator. And the compressor sucks the low pressure and low-temperature gaseous coolant, It is circulating in this way up to the realization of intended refrigeration.

scandomestic OFC 191 E Impulse Cooler - fig01

Circuit Diagram

scandomestic OFC 191 E Impulse Cooler - Diagram

Major Parameters

| OFF 191 E| OFC 222 E| OFC 231 E| OFC 381 E
---|---|---|---|---
Coolant and injection quantity (g)| R290(130)| R290(143)| R290(143)| R290(148)
General Rated input power (W)| 810| 1300| 1300| 1300
The power running of the electrical heating element (W)| /| 490| 490| 490
Max. ambient temp./RH| <27°C/70%| <27°C/70%| <27°C/70%| <27°C/70%
Refrigeration temperature (°C)| 2-10| 2-10| 2-10| 2-10
Kind of climate| 6| 6| 6| 6
Lamp Power (W)| 2,52(LED)| 2,54(LED)| 2,52(LED)| 2,52(LED)
Rated Current (A)| 5| 6,7| 6,7| 6,7
Total effective volume (L)| 190| 220| 230| 380
Net weight (kg)| 100| 96| 82| 107
Rated voltage (V)| 230| 230| 230| 230
Rated Frequency (Hz)| 50| 50| 50| 50
Foaming agent| Cyclopentane| Cyclopentane| Cyclopentane| Cyclopentane
Overall dimension (mm) (LxWxH)| 700x780x1473| 494x674x1742| 600x890x1520| 1000x890x1520

Note

  1. The electric circuit diagram and parameters on the product nameplate are final ones if they have been changed.

  2. The design might be proved without notice.

  3. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
    Children should be supervised to ensure that they do not play with the appliance.

  4. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.

WARNING: Refrigerant is facility burning of R290, please protect against fire.

Meaning of crossed-out wheeled dustbin:
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact your local government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.
When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposal at least free of charge.

The light source in this product is replaceable only by a professional
Lamp type: LED-light. Energy efficiency level: G

Access to professional repairs, such as internet webpages, addresses, and contact details.
Model no: OFC 231 E

Aftersales service station list:

Address Scandomestic A/S
Contact Number 72425571
Website Scandomestic.dk
QR code 997307

Relevant information for ordering spare parts, directly or through other channels provided by the manufacturer, importer, or authorized representative;| Scandomestic A/S
The minimum period during which spare parts, necessary for the repair of the appliance, are available;| 8 years
Instruction on how to find the model information in the product database, as defined in Regulation (EU) 2019/2019 by means of a web link that links to the model information as stored in the product database or a link to the product database and information on how to find the model identifier on the product.)| www.scandomestic.dk

Note: The address or contact phone number of the service site is subject to change without prior notice. Please confirm whether the service station is directly affiliated with one of our companies when requiring services.

DECLARATION OF CONFORMITY

Ref. Ares In accordance with EN ISO 17050-1:2004

Model number (unique identification of the product): OFC 191 E
Name and address of the manufacturer or his authorized representative:

Scandomestic A/S
Linåvej 20
8600 Silkeborg
Denmark
This declaration of conformity is issued under the sole responsibility of the manufacturer (or installer):| Scandomestic A/S
Linåvej 20
8600 Silkeborg
Denmark
The object of the declaration (identification of product allowing traceability. It may include a color image of sufficient clarity to enable the identification of the product, where appropriate.)
Product: Commercial Cooler
Brand: Scancool
Colour: Silver
Model name: OFC 191 E|
The object of the declaration described in point 4 is in conformity with the relevant Union harmonization legislation:| EN 61000-3-2
References to the relevant harmonized standards used, or references to the specifications in relation to which conformity is declared:| EU 2019/2018, 2017/1369, 2019/2024, 2009/125/EC, ISO 23953-1:2015, ISO 239532:2015, GB/T 19001-2016/ISO9001:2015,
EN 60335-2-89:2010+A1:2016+A2:2017,
EN 603351:2012+A11:2014+A13:2017+A1:2019+A14:2019+A2:2019,
EN 62233:2008, MD 2006/42/EC, IEC 60335-2-89:2019,
IEC 603351:2010, COR1:2010, COR2:2010, AMD1:2013, COR1:2014, AMD2:2016, COR1:2016,
EN 610006-3:2007+A1:2011,
EN 61000-6-1:2007, 2014/30/EU, 2015/863, 2011/65/EU
Where applicable: the notified body … (name, number)… performed … (description of intervention)… and issued the certificate:| RoHS 2011/65/EU + (EU) 2015/863
Additional information:| The appliance is intended exclusively for storing beverages
Model number (unique identification of the product):| OFC 222 E
---|---
Name and address of the manufacturer or his authorized representative:| Scandomestic A/S
Linåvej 20
8600 Silkeborg
Denmark
This declaration of conformity is issued under the sole responsibility of the manufacturer (or installer):| Scandomestic A/S
Linåvej 20
8600 Silkeborg
Denmark
The object of the declaration (identification of product allowing traceability. It may include a color image of sufficient clarity to enable the identification of the product, where appropriate.)
Product: Commercial Cooler
Brand: Scancool
Colour: Silver
Model name: OFC 222 E|
The object of the declaration described in point 4 is in conformity with the relevant Union harmonization legislation:| EN 61000-3-2
References to the relevant harmonized standards used, or references to the specifications in relation to which conformity is declared:| EU 2019/2018, 2017/1369, 2019/2024,
2009/125/EC, ISO 23953-1:2015, ISO 239532:2015,
GB/T 19001-2016/ISO9001:2015,
EN 60335-2-89:2010+A1:2016+A2:2017,
EN 603351:2012+A11:2014+A13:2017+A1:2019+ A14:2019+A2:2019,
EN 62233:2008, MD  2006/42/EC, IEC 60335-2-89:2019, IEC 603351:2010, COR1:2010,
COR2:2010, AMD1:2013, COR1:2014, AMD2:2016, COR1:2016,
EN 610006-3:2007+A1:2011,
EN 61000-6-1:2007, 2014/30/EU,  2015/863, 2011/65/EU
Where applicable: the notified body … (name, number)… performed …
(description of intervention)… and issued the certificate:| RoHS 2011/65/EU + (EU) 2015/863
Additional information:| The appliance is intended exclusively for storing beverages

Ref. Ares In accordance with EN ISO 17050-1:2004

Model number (unique identification of the product): OFC 231 E
Name and address of the manufacturer or his authorized representative:

Scandomestic A/S
Linåvej 20
8600 Silkeborg
Denmark
This declaration of conformity is issued under the sole responsibility of the manufacturer (or installer):| Scandomestic A/S
Linåvej 20
8600 Silkeborg
Denmark
The object of the declaration (identification of product allowing traceability. It may include a color image of sufficient clarity to enable the identification of the product, where appropriate.)
Product: Commercial Cooler
Brand: Scancool
Colour: Silver
Model name: OFC 231 E|
The object of the declaration described in point 4 is in conformity with relevant Union harmonization legislation:| EN 61000-3-2
References to the relevant harmonized standards used, or references to the specifications in relation to which conformity is declared:| EU 2019/2018, 2017/1369, 2019/2024,
2009/125/EC, ISO 23953-1:2015, ISO 239532:2015, GB/T 19001-2016/ISO9001:2015,
EN 60335-2-89:2010+A1:2016+A2:2017,
EN 603351:2012+A11:2014+A13:2017+A1:2019+ A14:2019+A2:2019,
EN 62233:2008, MD  2006/42/EC, IEC 60335-2-89:2019, IEC 603351:2010, COR1:2010, COR2:2010, AMD1:2013, COR1:2014, AMD2:2016, COR1:2016,
EN 610006-3:2007+A1:2011,
EN 61000-6-1:2007, 2014/30/EU, 2015/863, 2011/65/EU
Where applicable: the notified body … (name, number)… performed …
(description of intervention)… and issued the certificate:| RoHS 2011/65/EU + (EU) 2015/863
Additional information:| The appliance is intended exclusively for storing beverages

Ref. Ares In accordance with EN ISO 17050-1:2004

Model number (unique identification of the product): OFC 381 E
Name and address of the manufacturer or his authorized representative:

Scandomestic A/S
Linåvej 20
8600 Silkeborg
Denmark
This declaration of conformity is issued under the sole responsibility of the manufacturer (or installer):| Scandomestic A/S
Linåvej 20
8600 Silkeborg
Denmark
The object of the declaration (identification of product allowing traceability. It may include a color image of sufficient clarity to enable the identification of the product, where appropriate.)
Product: Commercial Cooler
Brand: Scancool
Colour: Silver
Model name: OFC 381 E|
The object of the declaration described in point 4 is in conformity with the relevant Union harmonization legislation:| EN 61000-3-2
References to the relevant harmonized standards used, or references to the specifications in relation to which conformity is declared:| EU 2019/2018, 2017/1369, 2019/2024, 2009/125/EC, ISO 23953-1:2015, ISO 239532:2015, GB/T 19001-2016/ISO9001:2015,
EN 60335-2-89:2010+A1:2016+A2:2017,
EN 603351:2012+A11:2014+A13:2017+A1:2019+ A14:2019+A2:2019,
EN 62233:2008, MD 2006/42/EC, IEC 60335-2-89:2019, IEC 603351:2010, COR1:2010,
COR2:2010, AMD1:2013, COR1:2014, AMD2:2016, COR1:2016,
EN 610006-3:2007+A1:2011,
EN 61000-6-1:2007,2014/30/EU,2015/863,2011/65/EU
Where applicable: the notified body … (name, number)… performed …
(description of intervention)… and issued the certificate:| RoHS 2011/65/EU + (EU) 2015/863
Additional information:| The appliance is intended exclusively for storing beverages

scandomestic logoScandomestic A/S
DK-8600 Silkeborg
CVR No.: 29774242
Tel.: + 45 7242 5571
www.scandomestic.dk

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals