Promethean TP-3165 ActivPanel 9 WiFi and Bluetooth Module Installation Guide

Promethean TP-3165 ActivPanel 9 WiFi and Bluetooth Module

USER SUPPORT

https://support.prometheanworld.com

WHAT’S IN THE BOX

INSTALLATION

INFORMATION

TP-3165-EN-V01 ©2022 Promethean Limited. All rights reserved. All software, resources, drivers, and documentation supplied in the Prometh an ActivInspire download are copyright Promethean Limited 2022. Promethean grants a license to install and use Promethean Activin spire software, including any resources, drivers, and documentation supplied in the download. Refer to the license agreement for information about the terms and conditions of this license. Promethean is the owner of a number of trademarks in several jurisdictions across the world. The Promethean products documented in this guide include aspects that are protected under their respective patent, copyright, design copyright, registered design, and trademark laws. The terms HDMI, HDMI High- Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.VESA is a registered mark of the Video Electronics Standards Association. Apple is a trademark or registered trademark of Apple, Inc. in the United States and other countries. Windows is a registered trademark or trademark of Microsoft Corporation in the United States and other countries. Linux is a registered trademark of Linus Torvalds in the United States and other countries. All other trademarks remain the property of their respective owners. This guide is distributed online. It may only be reproduced for use within the institution in which the product is used. For use outside of your institution, no part of this guide may be reproduced, transmitted, stored in a retrieval system, or translated into any other language without the prior permission of Promethean Limited. Please note that the content in this guide is protected under copyright law. Although every care has been taken in the compilation of this guide, Promethean Limited accepts no responsibility for errors or omissions, or for damages resulting from the use of the information contained within this guide.

Compliance

United States of America

FCC part 15.105

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC part 15.19
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC part 15.407
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

FCC Part 407
The device shall automatically discontinue use transmission in cases of absence of information to transmit, or operational failure. Then it will scan the available radio signals. If this signal is connected before, it will be automatically connected, otherwise manual connections will be necessary. Limited Modular Approval The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. The module must be installed in an Activ Panel. In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. This device complies with

FCC parts 15C:
15.247 and 15.407. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. The module should be installed at a minimum distance of 20 cm away from a person nearby. The host product manufacturer should state this information in the host instruction manual. Trace antenna designs- not applicable.

Model name: Activ Panel 9 Wi-Fi and Bluetooth Module
Product description: 2.4 GHz and 5 GHz Wi-Fi and Bluetooth Module Antenna type Antenna gain External Antenna
WLAN 2412 MHz to 2472 MHz: Max gain: 3.9 dBi WLAN 5150 MHz to 5250
MHz: Max gains: 5.3 dBi WLAN 5250 MHz to 5350 MHz: Max gain: 44 dBi WLAN 5470 MHz to 5725 MHz
Max gain: 3 dBi WLAN 5725 MHz to 5850 MHz Max gain 32 dBi
Frequency Bands and Power Frequency band Power (dBm)

• Bluetooth 2402 to 2480 MHz 20 WLAN 2412 MHz to 2472 MHz <20
• WLAN 5150 MHz to 5250 MHz <23
• WLAN 5250 MHz to 5350 MHz <20
• WLAN 5470 MHz to 5725 MHz <20
• WLAN 5725 MHz to 5850 MHz <14

Manufacturer’s name and address: Promethean Limited Promethean House, Whitebirk Industrial Estate, Lower Philips Rd, Blackburn BB1 STH. Promethean House, Whitebirk Industrial Estate, Lower Philips Rd, Blackburn BB1 5TH.

Canada

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

In device Tor operation in that band, s150-5250 MHZ IS only or indoor use to reduce the potential Tor harmful interference to co-channel mobile satellite systems. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Frequency Bands and Power

Frequency band Power (dBm)

• Bluetooth 2402 to 2480 MHz <20
• WLAN 2412 MHz to 2472 MHz 20
• WLAN 5150 MHz to 5250 MHz 23
• WLAN 5250 MHz to 5350 MHz 20
• WLAN 5470 MHz to 5725 MHz20
• WLAN 5725 MHz to 5850 MHz <14
• Bluetooth 2402 to 2480 MHz 20
• WLAN 2412 MHz to 2472 MHz 20
• WLAN 5150 MHz to 5250 MHz 23
• WLAN 5250 MHz to 5350 MHz 20
• WLAN 5470 MHz to 5725 MHz 20
• WLAN 5725 MHz to 5850 MHz 14

Manufacturer’s name and address: Promethean Limited Promethean House, Whitebirk Industrial Estate, Lower Philips Rd, Blackburn BB1 5TH.

Europe

We Promethean Limited declare under our sole responsibility that the ActivPanel 9 Wi-Fi and Bluetooth Module
Model No: AP9- WIFIBT-AB; conforms to the essential requirements of European Union Directive 2014/53/EU Radio Equipment Directive (RED) and 2011/65/EU Restriction of Hazardous Substances in Electrical and Electronic Equipment. The full text of the EU declaration of conformity is available at the following internet address: https://support.promethean-world.com

WARNING
AP9-WIFIBT-AB is a Class B product. In a domestic environment, they may cause interference in which case the user may be required to take adequate measures.

Frequency Bands and Power
Frequency band Power (dBm)

• Bluetooth 2402 to 2480 MHz <20
• WLAN 2412 MHz to 2472 MHz <20
• WLAN 5150 MHz to 5250 MHz <23
• WLAN 5250 MHz to 5350 MHz <20
• WLAN 5470 MHz to 5725 MHz 20
• WLAN 5725 MHz to 5850 MHz <14

Manufacturer’s name and address: Promethean Limited Promethean House, Whitebirk Industrial Estate, Lower Philips Rd, Blackburn BB1 5TH.

United Kingdom

We Promethean Limited, declare under our sole responsibility that this product conforms to the essential requirements of UK Legislation: RED Radio Equipment Regulation 2017 -the UK SI 2017 No. 1206, LVD The Electrical Equipment (Safety) Regulations 2016-UK SI 2016 No. 1101, RoHS Restriction of the use of certain Hazardous Substances in Electrical and Electronic Regulations 2012-UK SI 2012 No. 3032.

The full United Kingdom Declaration of Conformity can be found by searching for the model name at support.prometheanworld.com.

Frequency Bands and Power
Frequency band Power (dBm)

• Bluetooth 2402 to 2480 MHz 20
• WLAN 2412 MHz to 2472 MHz <20
• WLAN 5150 MHz to 5250 MHz23
• WLAN S250 MHz to 5350 MHz <20
• WLAN 5470 MHz to 5725 MHz 20
• WLAN 5725 MHz to 5850 MHz <14

Antenna type Antenna gain

External Antenna

• WLAN 2412 MHz to 2472 MHz: Max gain: 3.9 dBi
• WLAN 5150 MHz to 5250 MHz: Max gain: 5.3 dBi
• WLAN 5250 MHz to 5350 MHz: Max gain: 4.4 dBi
• WLAN 5470 MHz to 5725 MHz: Max gain: 3 dBi
• WLAN 5725 MHz to 5850 MHz: Max gain: 3.2 dBi

WARNING
AP9-WIFIBT-AB is a Class B product. In a domestic environment, they may cause interference in which case the user may be required to take adequate measures. AP9-WIFIBT-AB is for internal use only. The device complies with RF specifications when the device is used at 20 cm from your body. Manufacturer’s name and address: Promethean Limited Promethean House, Whitebirk Industrial Estate, Lower Philips Rd, Blackburn BB15TH.

Waste Electrical and Electronic Equipment (WEEE)
For more information concerning the correct disposal of these products, please contact our Promethean reseller.

Russian importer details LLC «STARTTEH»

Address: 125315, Moscow, 80KD, 3rd Floor, Apartment II, Room 32B. Registration No.:5137746235853.
INN/KPP: 7743911253/774301001 Rated power consumption: 12-19 V=60 W

KDB996369

D03 2.2 List of applicable FCC rules
List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT ist compliance with unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.10 below concerning the need to notify host manufacturers that further testing is required.

Explanation: This module meets all the requirements of FCC part 15-247&FCC Part 15, Subpart E (15.407) 2.3 Summarize the specific operational use conditions Describe use conditions that are applicable to the modular transmitter, including for example any limits on antennas, etc. For example, if point-to-point antennas are used that require reduction in power or compensation for cable loss, then this information must be in the instructions. If the use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual. In addition, certain information may also be needed, such as peak gain per frequency band and minimum gain, specifically for master devices in 5 GHz DFS bands.

Explanation: The EUT uses an External rubber antenna with a maximum gain of 5.3dBi. There is no restriction on the installation method. 2.4 Limited module procedures If a modular transmitter is approved as a “limited module,” then the module manufacturer is responsible for approving the host environment that the limited module is used. The manufacturer of a limited module must describe, both in the filing and in the installation instructions, the alternative means that the limited module manufacturer uses to verify that the host meets the necessary requirements to satisfy the module limiting conditions. A limited module manufacturer has the flexibility to define its alternative method to address the conditions

Explanation: This module is a limited module with 2.5 Trace antenna designs For a modular transmitter with trace antenna designs, see the guidance in Question 11 of KDB Publication 996369 D02 FAQ – Modules for Micro-Strip Antennas and traces. The integration information shall include for the TCB review the integration instructions for the following aspects: layout of trace design, parts list (BOM), antenna, connectors, and isolation requirements.

• Information that includes permitted variances (e.g, trace boundary limits, thickness, length, width, shape(s), dielectric constant, and impedance as applicable for each type of antenna);
• Each design shall be considered a different type (e.g., antenna length in multiple(s) of frequency, the wavelength, and antenna shape (traces in phase) can affect antenna gain and must be considered);
• The parameters shall be provided in a manner permitting host manufacturers to design the printed circuit (PC) board layout;
• Appropriate parts by manufacturer and specifications;
• Test procedures for design verification and) Production test procedures for ensuring compliance.

Explanation: YES. this module without trance antenna designs, use an External rubber antenna

RF exposure considerations
It is essential for module grantees to clearly and explicitly state the RF exposure conditions that permit a host product manufacturer to use the module. Two types of instructions are required for RF exposure information: (1) to the host product manufacturer, to define the application conditions (mobile, portable xX cm from a person’s body); and (2) additional text needed for the host product manufacturer to provide to end users in their end-product manuals. If RF exposure statements and use conditions are not provided, then the host product manufacturer is required to take responsibility for the module through a change in FCC D (new application).

Explanation: This module complies with FCC RF radiation exposure limits set forth for an uncontrolled environment The module is designed to comply with the FCC statement, TCC id IS: UAMOZ3 2.7 Antennas A ist of antennas included in the application for certification must be provided in the instructions. For modular transmitted approved as time modules, all applicable professional installer instructions must be included as part of the information to the host product manufacturer. The antenna list shall so identify the antenna types (monopole, A.dpole, etc (note that for example an omnidirectional For situations where the host product manufacturer is responsible for an external connector, for example with an RF Pin and antenna trace design, the integration instructions shall inform the installer hat unique antenna connector must be used on Part 15 authorized transmitters used in the host product. The module manufacturers shall provide a list of acceptable unique connectors.

• Entenna2 R ain for 2400MHz-250OMHz
• External Antenna, 5.3dBi Gain for 5180MHz 5240MHz
• External Antenna, 4.4d5i Gain tor S260MHZ~ 5320MHZ
• External Antenna, 3.0dBi Gain for 5500MHz ~ 5700MHz

Label and compliance information Grantees are responsible for the continued compliance of their modules to the FCC rules. This includes advising host product manufacturers that they need to provide a physical or e-label stating that Contains FCC ID with their finished product. See Guidelines for Labeling and User Information for RF Devices – KDB Publication 784748.

Explanation: on the metal shielding shell, there is space Tor printing basic information such as the name and model of the product, and the id QAMOZ3 IS Included. 2.9 Information on test modes and additional testing requirements5 Additional guidance for testing host products is given in KDB Publication 996369 D04 Module integration Guide. In a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product. no grantee snow provide information on how to configure cestodes Tor noO5t product Evaluation Tor internet transmitting modules or another transmitter “do, VeiSus simple, Simutaneousiy Grantees can increase the utility of their modular transmitters by providing special means, modes, or instructions hat simulates or characterizes a connection by enabling a transmitter. It can greatly simplify a host manufacturer s determination that a module is installed in the most complex with FC requirements.

Explanation: Data transfer module demo board can control the EUT work in RF test mode at 2.10 Additional testing. Part 15 Subpart disclaimer the grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule parts (1.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance with any other FGC rules that apply to the host not covered Subnart R compliant hen unintentional. radiator digital circuity then the guarantee shall provide a notice stating that the final host product still requires Part 15 SUbpart B compliance testing with the modular transmitter installed.

This radio transmitter [IC:5459A-023] has been approved by Innovation, Science, and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited from use with this device.

ANTENNA TYPE

• 2.4G WLAN:
• ANTO: External Antenna, with 2.9dBi gain
• ANT1: External Antenna, with 2.9dBi gain 2.4G
• BT-LE/EDR: External Antenna, with 2.9dBi gain
• ANTO:
• External Antenna, 5.3dBi Gain for 5180MHz 5240MHz
• External Antenna, 4.4dBi Gain for 5260MHz ~ 5320MHz
• External Antenna, 3.0dBi Gain for 5500MHz ~5700MHz ANT1:
• External Antenna, 5.3dBi Gain for 5180MHz ~ 5240MHz
• External Antenna, 4.4dBi Gain for 5260MHz ~ 5320MHz
• External Antenna, 3.OdBi Gain for 5500MHz 5700MHz

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>