saunalife E8 Sconce Indoor and Outdoor Sauna Light Set Installation Guide

June 16, 2024
saunalife

saunalife E8 Sconce Indoor and Outdoor Sauna Light Set

saunalife-E8-Sconce-Indoor-and-Outdoor-Sauna-Light-Set-
FIG-1

Product Information

Specifications

  • Sconce Light Specifications:
    • Kelvin: 3500k
    • IP Rating: IP67
    • Certification: CE / FCC
    • Operating Voltage (VDC): 24V DC
    • Max Wattage: 6.4W
    • Lumens: 703
    • Dimensions: 15-3/4 x 12-1/4 x 3-1/4
  • Led Light Bar Specifications:
    • IP Rating: IP67
    • Certification: CE / FCC
    • Operating Voltage (VDC): 24V DC
    • Max Wattage:
    • E6 BP031085 LED White: 11.32W
    • E7 BP031086 LED White: 14.27W
    • E8 BP031158 LED White: 18.69W
    • Lumens:
    • E6 BP031085 LED White: 1,246
    • E7 BP031086 LED White: 1,571
    • E8 BP031158 LED White: 2,059
    • Dimensions (with flush clips):
    • E6 BP031085 LED White: 3/4W x 9/16H x 3/4W x 1-1/4H
    • E7 BP031086 LED White: 3/4W x 9/16H x 3/4W x 1-1/4H
    • E8 BP031158 LED White: 3/4W x 9/16H x 3/4W x 1-1/4H
    • Dimensions (with adjustable clips):
    • E6 BP031085 LED White: 48L x 48L
    • E7 BP031086 LED White : 60L x 60L
    • E8 BP031158 LED White: 76L x 76L

Product Usage Instructions

  • Step 1. Installation of Sconce Lights
    • Locate the provided mounting template and mount it at the desired light location to determine the mounting screw locations and light cable access.
    • Recommended light installation height is 5ft from the base and 16in from the side wall.
    • Repeat this step for the second light.
  • Step 2. Run Light Cable
    • Running the light cable will depend on your installation.
    • If the cable can be routed outside to the driver location, proceed accordingly.
    • If going through the barrel, use a 3/4 drill bit for the cable to pass through.
    • Repeat this step for the second light.
  • Step 3. Install Mounting Brackets & LED Light Bar
    • Determine the location where the LED light bar will be installed.
    • Screw the Mounting Clips to the surface, ensuring even coverage of the light fixture.
    • Carefully snap the LED light bar into each clip.
  • Step 4. Connect 2-Pin 30′ Cable to Light Bar
    • Connect the light cable end to the lead of the light bar.
    • At the Driver, connect it to one of the 4 leads on the 2-Pin 4-Way cable.
  • Step 5. Install Power Supply
    • Connect the AC power cord cable to the power supply block.
    • Place the power supply near the RF driver.
    • Connect the DC cable end from the power supply and connect it into the RF driver DC IN port.

FAQ

  • Can the RF Driver and Power Supply be installed outdoors?
    Yes, they can be installed outdoors but must be protected from rain and snow. They should be installed in a waterproof electrical enclosure.

  • What should be the minimum distance between the RF Driver and Power Supply and the heat source inside the sauna?
    The minimum distance should be 20 inches from the heat source, and the maximum height should be 20 inches off the floor or in the fan’s path.

  • How should I place the Sconce Lights to avoid direct contact with bathers’ eyes?
    Each fixture should be carefully placed to avoid direct contact with the bathers’ eyes.

  • Are there any specific requirements for the installation tools?
    The required tools for installation are a cordless drill and a 3/4 wood drill bit (installation dependent). A level should also be used for accurate installation.

LED Lightbar Package Contents

saunalife-E8-Sconce-Indoor-and-Outdoor-Sauna-Light-Set-
FIG-2

Installation Recommendations

Please read this manual in its entirety prior to installation and keep it in a safe place after for future reference. ****

  • IMPORTANT The RF Driver and Power Supply may be installed outdoors but must be protected from rain and snow. RF Driver and Power Supply should be installed in a waterproof electrical enclosure.
  • IMPORTANT When installing the RF Driver and Power Supply inside the sauna, maintain a minimum distance of 20” from heat source and a maximum height of 20” off floor or in fan’s path.
  • IMPORTANT If installed inside the sauna, the RF Control must not exceed 131°F. Control should be no more than 3′ off the floor and away from heater. Test temperature reading of location before mounting.
  • IMPORTANT Consider light placement carefully. Each fixture should be placed to avoid direct contact with the bathers eyes.
  • IMPORTANT LED Light Bar max operating temperature is 195°F, installing LED light bar in location where temperature will exceed 195°F may cause light failure

Electrical Requirements

  • A 120V AC electrical outlet is needed to power the lighting system.
  • Your electrician will determine the type of electrical outlet, box, and piping to be used.
  • All wiring must be done in accordance with national elec-tric code and local building codes by a certified electrician.
  • Improper voltage or connections will damage the compo-nents and void warranty.

Required Tools

Specifications

saunalife-E8-Sconce-Indoor-and-Outdoor-Sauna-Light-Set-
FIG-4

INSTALLATION INSTRUCTION

  • STEP 1.

    • Installation of Sconce Lights
      Locate provided mounting template and mount at light location to locate mounting screw locations and light cable access. Recommended light installation height 5ft from base and 16in from side wall.

    • Repeat this step for second light.

  • STEP 2.

    • Run Light Cable
      Running the light cable will be dependent on your installation. Cable can be routed outside to driver location or through the barrel. If going through the barrel use a 3/4” drill bit for cable to pass-through.

    • Repeat this step for second light

  • STEP 3.
    Install Mounting Brackets & LED Light Bar
    Determine the location where LED light bar will be installed. Screw Mount-ing Clips to surface ensuring even coverage of light fixture. Carefully snap LED light bar into each clip.

  • STEP 4.
    Connect 2-Pin 30’ Cable to Light Bar
    Connect the light cable end to lead of the light bar. At Driver, connect to one of the 4 leads on the 2-Pin 4-Way cable

  • STEP 5.
    Install Power Supply
    Connect AC power cord cable to power supply block. Place power supply near RF driver. Connect DC cable end from power supply and connect into RF driver DC IN port.

saunalife-E8-Sconce-Indoor-and-Outdoor-Sauna-Light-Set-
FIG-7

Wi-Fi Setup

On IOS or Android down-load the Tuya Smart App
To set up Wi-Fi operation follow the steps below
Note: Wi-Fi Driver supports 802.11 b / g / n 2.4 GHz Wi-Fi standard. The Wi-Fi Driver

  • Step 1 Open Tuya app and press Sign
  • Step 2  Up to create an account
  • Step 3  Enter an email address to register an account
  • Step 4  Check email and enter verification code
  • Step 5  Create a password

saunalife-E8-Sconce-Indoor-and-Outdoor-Sauna-Light-Set-
FIG-8

  • Step 5 Main screen press Add Device
  • Step 6 Press Add next to Discovering Devices
  • Step 7 Select your Wi-Fi network
  • Step 9 Device added success- fully, press done to complete setup

saunalife-E8-Sconce-Indoor-and-Outdoor-Sauna-Light-Set-
FIG-9

Troubleshooting

  • No Power

    • Verify that the electrical outlet has voltage.
    • Check that connections on the Power Supply are secure.
    • Check that the DC barrel plug on the Power Supply is securely connected.
  • Power but light’s not turning on

    • Check that the Pigtail cable from the Driver is securely connected and that wiring is correct.

    • Check that 4-way light cable is secure and connected.

    • Check that all 30’ cables to lights are securely connected.

    • Verify each light functions by testing them directly to the Driver independently.
      Note: To test individual light, disconnect 4-way light cable and connect 30’ cable directly to Pigtail lead off Driver, or connect light directly to Pigtail.

    • Verify that RF Remote is paired with Driver.

  • Lights on but no function from Control

    • Verify battery is inserted correctly.
    • Low battery, replace with new battery.
    • Check that DC power cable from Driver to Control is securely connected.
    • Ensure that the distance from the Remote to the Driver is not more than 98 feet. If so, relocate Driver closer to room.

Replacement Parts

saunalife-E8-Sconce-Indoor-and-Outdoor-Sauna-Light-Set-
FIG-10

Technical Support224-253-5909

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals