DREMEL 910 Glue Gun Instruction Manual
- June 3, 2024
- DREMEL
Table of Contents
DREMEL 910 Glue Gun
ORIGINAL INSTRUCTIONS
USED SYMBOLS
READ THESE INSTRUCTIONS
CLASS II CONSTRUCTED
DO NOT DISPOSE OF ELECTRIC TOOLS, ACCESSORIES AND PACKAGING TOGETHER WITH HOUSEHOLD WASTE MATERIAL
WORKING SAFELY WITH THIS UNIT IS POSSIBLE ONLY WHEN THE OPERATING AND SAFETY INFORMATION ARE READ COMPLETELY AND THE INSTRUCTIONS CONTAINED THEREIN ARE STRICTLY FOLLOWED.
- If the cable is damaged or cut through while working, do not touch the cable but immediately pull the mains plug. Never use the unit with a damaged cable.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
- The unit must not be damp and must also not be operated in damp surroundings.
- For indoor use only.
- Connect units that are used outdoors by means of a fault current protection switch (FI) with a maximum triggering current of 30 mA. Use only an extension cable that is approved for outdoor use.
- Always direct the cable to the rear away from the unit.
- For pauses in the work of more than 30 minutes, pull the mains plug.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
- Children shall not play with the appliance.
- Cleaning and user maintenance shall not be made by children without supervision.
- Dremel is able to ensure flawless functioning of the unit only if the original accessories intended for it are used.
- Do not work materials containing asbestos (asbestos is considered carcinogenic).
- Take protective measures when during work dust can develop that is harmful to one’s health, combustible or explosive (some dusts are considered carcinogenic); wear a dust mask and work with dust/ chip extraction when connectable.
- Do not change nozzles while glue gun is in “on” position, plugged in, or warm to the touch. Before changing nozzles, make sure glue gun is cool to the touch, unplugged, and the switch is in the “off” position.
ENVIRONMENT
DISPOSAL
The unit, accessories and packaging should be sorted for environment-friendly
recycling.
ONLY FOR EUROPEAN COUNTRIES
Do not dispose of power tools into household waste! According to the European
Guideline 2012/19/EC for Waste Electrical and Electronic
Equipment and its implementation into national right, power tools that are no
longer usable must be collected separately and disposed of in an
environmentally correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
EXTENSION CORDS
Use completely unrolled and safe extension cords with a capacity of at least 5
Amps.
ASSEMBLY
GENERAL
The glue gun is intended for the quick gluing of clean, dry and grease-free
materials with glue heated to its melting point.
PICTURE 1a/1b
-
Nozzle
-
Glue stick
-
Feed trigger
-
Stand
-
Temperature switch
PICTURE 1c -
On/off switch with indicator light
-
Detachable cord
-
Stand release button
-
Exchangeable nozzle
USE
SWITCHING ON/OFF
SWITCHING ON:
Plug Dremel Glue Gun into a standard 230 V electrical outlet.
Models 910, 920 and 930:
- Once the glue gun is plugged in, it is on and heating.
Dual Temperature Glue Gun Model 930:
- Adjust switch (5) to low or high temperature setting to turn the Glue Gun on. Consult with glue stick package to determine appropriate temperature.
Model 940:
- Connect the power cord to the glue gun.
- Switch the glue gun on with the main switch. Indicator light (6) will let you know the glue gun is on and heating.
SWITCHING OFF:
- Pull the mains plug (models 910, 920 and 930).
- Switch the unit ON/OFF with switch (6; model 940). Pull the mains plug.
Allow the unit to cool completely before storing.
The hot nozzle can cause damage.
GETTING STARTED
PREPARATIONS FOR GLUING
The surfaces to be glued must be clean, dry and free of grease. Roughen smooth surfaces before gluing. DO NOT USE INFLAMMABLE SOLVENTS FOR CLEANING! The ambient temperature and the work piece to be glued must not be colder than +5 °C or warmer than +50 °C. Warm rapidly cooling materials (e.g., steel) for better adhesion.
GLUING
DANGER OF BURNING! The glue and the nozzle tip (1) become very hot. Do
not allow the nozzle tip or hot glue to come into contact with persons or
animals. If hot glue touches the skin, immediately hold the spot for some
minutes under a stream of cold water. Do not try to remove the glue from the
skin.
Models 910, 920 and 930:
- Allow glue gun to reach operating temperature before using (±5mins).
Insert the glue stick (2). Press the feed trigger (3).
Model 940:
-
Once the cord is detached, the glue gun remains operable for 5mins, before it needs to heat up.
NOTE: For your first use, you may need to load up to two full glue sticks before glue begins to flow. -
Squeeze trigger (3) to apply glue onto desired surface.
-
Apply parts together.
-
Allow glue to cool before handling object or surface.
TIP: Dremel also supplies glitter and colour sticks for decorative purposes. These sticks have been specially developed for creative projects and low temperature (105 °C).
The colour sticks can also be used for sealing decorations. To be able to quickly change colours, it is recommended to cut the sticks into 3 cm pieces before inserting into the Glue Gun.
GLUESTICKS
DRIP-CONTROL FUNCTION
When heated up, the glue gun has a drip-control function. This prevents the
glue from dripping when the glue gun is at operating temperature.
NOTES: During heating-up the glue gun may release a few drops of glue.
Do not use glitter or colour sticks at high temperature. The drip-control
function will not work properly.
Model 940: EXCHANGE NOZZLE
- Use a spanner and turn the nozzle from the housing.
- Mount a new nozzle on the housing.
CHANGING GLUE STICKS
Do not attempt to remove the unused portion of the glue stick from your glue
gun. If you need to switch glue stick formulas, empty the melting chamber by
squeezing the trigger and insert new formula.
STAND / KICK STAND
When glue gun is hot, do not lay on its side.
Always use stand.
- Push stand (4) into “down” position when temporarily not in use (models 910, 920 and 930).
- Push the stand release button (8) to release the stand (model 940).
When re-using or storing, push stand back into “up” position.
MAINTENANCE
CLEANING
BEFORE ANY WORK ON THE UNIT ITSELF, PULL THE MAINS PLUG.
Always keep the unit clean so that it functions properly and accurately.
SERVICE AND WARRANTY
This DREMEL product is guaranteed in accordance with statutory/country
specific regulations; damage due to normal wear and tear, overload or improper
handling will be excluded from the guarantee. If the unit should fail despite
the care taken in manufacturing and testing, send it undismantled together
with proof of purchase to your dealer.
CONTACT DREMEL
For more information on the Dremel assortment, support and hotline, go to
www.dremel.com
Dremel, Konijnenberg 60, 4825 BD Breda, The Netherlands
2610Z06195 01/2016
www.dremel.com
All Rights Reserved