iottie Easy One Touch Wireless Dash and Windshield Mount User Manual

iottie Easy One Touch Wireless Dash and Windshield Mount

Specifications

• Product Name: Easy One Touch Wireless 2
• Mount Type: Dash & Windshield Mount
• Compatibility: Qi-enabled smartphones including Google, Apple,& Samsung devices
• Wireless Charging Speed: Dependent on phone make and model
• Car Charger: Qualcomm Quick Charge 2.0 or above

Product Usage Instructions

Getting Started
For optimal mounting and charging, please follow the detailed instructions within this manual when using the Easy One Touch Wireless 2 Charging Mount. iOttie is not liable for possible damages due to product misuse.

Critical Information

• Compatibility: The Easy One Touch Wireless 2 is compatible with all Qi-enabled smartphones including Google, Apple, & Samsung devices. (Wireless charging speed is dependent on phone make and model.)
• Qi Wireless Charging in Vehicle: Use the included iOttie car charger and micro USB cable. If you use a third-party car charger, make sure that it is Qualcomm Quick Charge 2.0 or above.
• Interference: The Easy One Touch Wireless 2’s signal may interfere with your vehicle’s TPMS (tire pressure monitoring system). If you notice that your TPMS light turns on,reposition the mount to prevent the signals from interacting.

At a Glance

• Dual Car Charger with Micro USB Cable
• Qi Alignment Guide

Adjusting the Mount

Cradle knob: When switching between landscape and portrait mode, loosen the cradle knob to rotate the cradle.
Tighten the knob to lock the mount into your desired position.

Foot release button: The foot can be adjusted to 3 different height settings to accommodate different phone sizes. Once setup is chosen, the foot is designed to align with the center of the side arms for optimal Qi wireless charging.

Telescopic knob: Located on top of the telescopic arm, the knob can be loosened to extend the arm and tightened to secure the arm in place.

Pivot knob: Located on the side of the mount base, you can loosen the pivot knob to move the telescopic arm up or down. Tighten the knob to lock the arm into position.

Windshield or Curved Glass Installation
Choose a location on the windshield and wipe any dust or debris from the surface.

1. Attach the mount cradle to the ball joint.
2. Tighten the cradle knob.

Dashboard or Flat Surface Installation

Choose a flat location on the vehicle’s dashboard and wipe the surface clean.

1. Peel off the protective film on the suction cup and press firmly onto the windshield.
2. Push locking lever down to engage suction.

Note: When removing the dashboard pad, please use caution. We recommend removing slowly from the edge to avoid damage. We do not recommend using the dashboard pad for windshield mounting. To reuse the suction cup, simply rinse under warm water and let air dry to restore tacky suction.

Connecting to Power

1. Peel off the film on the dashboard pad & stick onto the desired installation location.
2. Peel off the protective film on the suction cup and press mount firmly onto the dashboard pad.
3. Push the locking lever down to engage suction.

FAQ

Q: Is the Easy One Touch Wireless 2 compatible with all smartphones?
A: The Easy One Touch Wireless 2 is compatible with all Qi-enabled smartphones including Google, Apple, & Samsung devices.

Q: Can I use a third-party car charger?
A: If you use a third-party car charger, make sure that it is Qualcomm Quick Charge 2.0 or above for optimal wireless charging.

Q: What should I do if my TPMS light turns on?
A: If you notice that your TPMS light turns on, reposition the mount to prevent the signals from interacting.

Easy One Touch Wireless 2
Dash & Windshield Mount ·

Getting Started

For optimal mounting and charging, please follow the detailed instructions within this manual when using the Easy One Touch Wireless 2 Charging Mount. iOttie is not liable for possible damages due to product misuse.

Critical Information

Compatibility
The Easy One Touch Wireless 2 is compatible with all Qi-enabled smartphones including Google, Apple, & Samsung devices.
(Wireless charging speed is dependent on phone make and model.)

Qi Wireless Charging in Vehicle
Use the included iOttie car charger and micro USB cable. If you use a third party car charger, make sure that it is Qualcomm Quick Charge 2.0 or above.
The Easy One Touch Wireless 2’s signal may interfere with your vehicle’s TPMS (tire pressure monitoring system). If you notice that your TPMS light turns on, reposition the mount to prevent the signals from interacting.

At a Glance

Qi Alignment Guide

The Qi receiver coil is usually located in the center area of the phone. Check with your phone’s manufacturer for Qi coil location. Below are some examples for commonly used phones.

For optimal wireless charging, please make sure your smartphone and mount’s Qi coils are aligned.

Adjusting the Mount

Cradle knob
When switching between landscape and portrait mode, loosen the cradle knob to rotate the cradle. Tighten the knob to lock the mount into your desired position.

Foot release button
The foot can be adjusted to 3 different height settings to accommodate different phone sizes. Once setup is chosen, the foot is designed to align with the center of the side arms for optimal Qi wireless charging.

Telescopic knob
Located on top of the telescopic arm, the knob can be loosened to extend the arm and tightened to secure the arm in place.

Pivot knob
Located on the side of the mount base, you can loosen the pivot knob to move the telescopic arm up or down. Tighten the knob to lock the arm into position.

Installation

Assembling the Mount

1. Attach the mount cradle to the ball joint.
2. Tighten the cradle knob.

Selecting a Location
Choose an installation method: Dashboard/Flat Surface (A) or Windshield/Curved Glass (B).

Option A
Dashboard or Flat Surface Installation
Choose a flat location on the vehicle’s dashboard and wipe the surface clean.

1. Peel off the film on the dashboard pad & stick onto the desired installation location.
2. Peel off the protective film on the suction cup and press mount firmly onto the dashboard pad.
3. Push the locking lever down to engage suction.

Option B
Windshield or Curved Glass Installation
Choose a location on the windshield and wipe any dust or debris from the surface.

1. Peel off the protective film on the suction cup and press firmly onto the windshield.
2. Push locking lever down to engage suction.
   • When removing the dashboard pad, please use caution. We recommend removing slowly from the edge to avoid damage.
   • We do not recommend using the dashboard pad for windshield mounting.
   • To reuse the suction cup, simply rinse under warm water and let air dry to restore tacky suction.

Connecting to Power

The Easy One Touch Wireless 2 is powered via a micro USB cable. There is no on/off switch on the mount. Once it is plugged in, the mount will remain on until the vehicle is turned off.

Using the Easy One Touch Mechanism

The Easy One Touch lock and release mechanism makes it simple to mount & retrieve smartphones in seconds.

Mounting

1. Squeeze the release bars on either side of the mount to open the locking side arms.
2. Press your device against the Easy One Touch trigger button. The mount’s arms will automatically close on contact for a secure hold.

Releasing
Press the release bars. The arms will open so you can retrieve your device.

Wireless Charger Specifications

INPUT

| DC 5V/3A DC 9V/2A DC 12V/1.5A
---|---
OUTPUT| 10W (ANDROID), 7.5W (APPLE)
CHARGING PORT| MICRO USB
LENGTH| 4.3″
WIDTH| 2.4″
HEIGHT| 4.5″
WEIGHT| 3.6 oz

Car Charger Specifications

OUTPUT

| DC 5V/3A

9V/2A

12V/1.5A

Charging Indicator

BLINKING RED LIGHT

| Smartphone is not charging.

Foreign object detected, or the smartphone or mount is overheating.

Declaration of Conformity (FCC)

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. You can refer to the following completed FCC warnings.
This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Operational Warnings

• During the charging process, the transfer of electricity gives off heat. Your device may become warm, but should not become exceedingly hot.
• If the device gets wet, please cease charging immediately. Remove all plugs and dry the product completely. Device is only to be operated in a dry, indoor environment.
• Please be careful of excessive drops, dents, punctures, or deformities on the device. If you are concerned, please unplug the device and contact the manufacturer.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• Operating this device in a hot environment or in direct sunlight for a long period of time may cause malfunctions. We recommend keeping the product in cooler temperatures.
• Please use included components for an optimal experience. To support Qi wireless charge when using a third party car charger or a USB Power Adapter use a minimum output of both “9.0V-1.67A or 5.0V-2.0A” and at least QC 2.0.
  • The product’s signal could possibly interfere with you TPMS (tire pressure monitoring system). If you notice that your TPMS light turns on, please try using your mount in different locations to avoid the signals from interfering with each other.
• California Proposition 65 this product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.

CAUTION
OLD ELECTRICAL APPLIANCES MUST NOT BE DISPOSED OF TOGETHER WITH THE RESIDUAL WASTE, BUT HAVE TO BE DISPOSED OF SEPARATELY.

IC Warning
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

EU Declaration
Hereby, iOttie declares that the radio equipment type HLCRIO142 is in compliance with Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the following web address: https://www.iottie.com/wp-content/uploads/2023/05/doc- hlcrio142_143_144.pdf

Request your warranty here
https://www.iottie.com/support/customerservice

If you love your iOttie product, let us know by leaving a review online, or connect with us on our social platforms.

www.iottie.com

cs@iottie.com

References

• iOttie - Best Selling Car Mounts and Mobile Accessories

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>